iottie Auto Sense CD Slot Air Vent Mount User Manual

June 16, 2024
iOttie

iottie Auto Sense CD Slot Air Vent Mount

Getting Started

For optimal mounting and charging. please follow the detailed instructions within this manual when using the Auto Sense Wireless Charging Mount. IOttie is not liable for possible damages due to product misuse.

Critical Information

  • Mounting at a perpendicular angle to the mount works best with the proximity sensor,
  • If mounting at an angle, the phone will need to be very close to the sensor for rms to open.

At a Glance

Qi Alignment Guide
The Qi receiver coil is usually located in the center area of the phone. Check with your phone’s manufacturer for Qi coil location. Below are some examples of commonly used phones.

For optimal wireless charging, please make sure your smartphone and mount’s Qi coils are aligned.

Adjusting the Mount

  1. Foot Knob
    The bottom foot is set to fit standard-sized smartphones. If you have a larger phone or use a thicker case, you can adjust the foot to accommodate your phone.

  2. To adjust the foot, simply move the knob down until it aligns with the appropriate size marking as shown in the line drawing.

Connecting to Power

  1. Plug the micro-USB cable into the USB port on the back of the mounting head.
  2. Insert the car charger into your vehicle’s power port.

Installation

CD Slot Mount

  1. Attach the CD mount to the cradle. Tighten using the adjustment knob
  2.  Put the mount into the CD slot and pull the lever to lock it into place
  3. Test to make sure the mount is secure. Insert bracket only if needed.
  4. If using the bracket, make sure the arrow is pointing inward
  5. Align your smartphone in the center of the cradle. The indicator light will turn on when the phone is successfully charging

To avoid possible damage to the product and your vehicle, remember to remove all CDs from the CD slot before using your  Auto Sense Mount. iOttie is not liable for damage due to misuse

Air Vent Mount

  1. Attach the air vent mount to the cradle. Tighten using the adjustment knob.
  2. Loosen the twist lock and push the mount completely onto the air vent blade
  3.  Slowly tighten the twist lock to ensure a secure connection to the air vent blade
  4.  Align the smartphone in the center of the cradle. The indicator light will turn on when the phone is successfully charging

Please use caution when adjusting the twist lock on the air vent blade.

Using the Auto Sense Mechanism

Once it is unplugged or the car is turned off, the Auto Sense’s internal battery keeps a charge for up to one hour.

Mounting and Charging

  1. The side arms will automatically open via a silent servo motor when a phone is detected by the proximity sensor.
  2. Once the phone is placed inside the mount, the arms will automatically close for a secure hold. Qi wireless charging will start immediately

Wireless Charger Specification

INPUT

| DC 9.0V-1.67A DC 5.0V-2.0A
---|---
CHARGING PORT| MICRO USB
LENGTH| 4.8″
WIDTH| 3″
HEIGHT| 4″
WEIGHT| 133 g

Car Charger Specifications

Charging Indicator

Solid Green Light

|

My smartphone is charging.

---|---

Blinking Red Light

| The smartphone is not charging.

Foreign objects are detected or the smartphone is overheating.

FCC Part 18 Compliance

This device complies with Part 18 of the FCC Rules.
CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the product.
NOTE: This equipment has been tested and found to comply with the limits for a wireless power transfer, pursuant to Part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Hereby, iOttie, Inc declares that the radio equipment type HLCRIO164 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.iottie.com.
Declaration for EU Compliance: Operation Freq: 118.59-151.12 kHz, Max.  RF power transmitted: H-Field 20.35dBμA/m @3m distance.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Operational Warnings

  • During the charging process, the transfer of electricity gives off heat. Your device may become warm, but should not become exceedingly hot.

  • If the device gets wet, please cease charging immediately. Remove all plugs and dry the product completely. The device is only to be operated in a dry, indoor environment.

  • Please be careful of excessive drops, dents, punctures, or deformities on the device. If you are concerned, please unplug the device and contact the manufacturer.

  • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
    the equipment.

  • Operating this device in a hot environment or in direct sunlight for a long period of time may cause malfunctions. We recommend keeping the product in cooler temperatures.

  • Please use the included components for an optimal experience. To support

  • Qi wireless charge when using a third-party car charger or a USB Power Adapter use a minimum output of both “DC 9.0V-1.67A or DC z5.0V-2.0A” and at least QC 2.0.

  • The product’s signal could possibly interfere with your TPMS (tire pressure monitoring system). If you notice that your TPMS light turns on, please try using your mount in different locations to avoid the signals from interfering with each other.

  • California Proposition 65 this product contains chemicals known to
    the state of California to cause cancer and birth defects or other reproductive harm.

CAUTION

OLD ELECTRICAL APPLIANCES MUST NOT BE DISPOSED OF TOGETHER  WITH THE RESIDUAL WASTE, BUT HAVE TO BE DISPOSED OF SEPARATELY.

IC Warning

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

The device has been evaluated to meet general RF exposure requirements.
To maintain compliance with RSS-102 – Radio Frequency (RF) Exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

THE RECOMMENDED DISTANCE BETWEEN YOU AND THE WIRELESS CHARGING DEVICE SHOULD BE AT LEAST:

DRIVER SEAT

Knee| 40cm
Leg| 60cm
Body| 70cm
Hands| 30cm
Arms| 70cm
Head| 80cm
FRONT PASSENGER SEAT

Knee| 43cm
Leg| 59cm
Body| 62cm
Hands| 46cm
Arms| 55cm
Head| 80cm

measurements are based on FCAR Car Models as described by the ACRISS Class Clode system.
EU Declaration
Hereby, iOttie declares that the radio equipment type HLCRIO164 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following web address:

https://www.iottie.com/wp-content/uploads/2023/05/doc-hlcrio161_164_165.pdf

If you love your iOttie product, let us know by leaving a review online, or connect with us on our social platforms.

Request your warranty here

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals