saunalife E8 Barrel Sauna Installation Guide

June 16, 2024
saunalife

saunalife E8 Barrel Sauna

Product Information

Specifications

  • Product Name : Ergo-Series E8 Barrel Sauna
  • Dimensions: 87D x 81H
  • Revision: 4/2023

Product Usage Instructions

To install the wooden front wall, follow these steps:

  1. Fix the wall diagonally to make it more rigid during installation. Use the provided brackets inside.
  2. Pre-drill holes with a 5/32 drill bit before inserting screws.
  3. Position cradles inside the grooves of stave 2 and center stave 2 on cradle 1.
  4. Use a water level to ensure proper alignment.
  5. Leave a 1/4 inch gap when tightening screws to allow for adjustment when installing the outer bands (B).

Wooden Back Wall Installation

To install the wooden back wall, follow these steps:

  1. Fix the wall diagonally to support it during installation. Use temporary braces and remove them later.
  2. Pre-drill holes with a 5/32 drill bit before inserting screws.

Outer Bands Installation

To install the outer bands, follow these steps:

  1. Place the bands around the barrel on the outer side of the cradle.
  2. Remove any temporary braces that were previously used.

Board Installation

To install the boards, follow these steps:

  1. Join two boards together to bridge the width of the gap. The combined boards should be approximately 1/4 inch wider than the gap.
  2. Raise the boards slightly before installing them.
  3. If needed, trim the flat edge of the board to create the desired width.
  4. Fasten the two halves using screws.

Benches Installation

To install the benches, follow these steps:

  1. Use a level for proper installation.
  2. Pre-drill holes with a 1/8 drill bit before inserting screws.

FAQ

  • Q: What tools are needed for installation?
    • A: The following tools are needed for installation: measuring tape, marker pen, circular saw, water level, hammer, ratchet strap, extra hands, silicone gun (only for glass-wall models), drill, crescent wrench, utility knife, and rubber mallet.
  • Q: How many screws and bits are included?
    • A: The package includes approximately 2 lbs. of screws and the following Torx bits: T10, T15, T20, T25.
  • Q: How many cradles are included?
    • A : The package includes cradles for center stave 2.
  • Q: Can I adjust the boards after installation?
    • A : Yes, leave a 1/4 inch gap when tightening screws to allow for adjustment when installing the outer bands.

Note : Please read manual before construction

Front & Back Walls

saunalife-E8-Sauna-FIG1

E8 Barrel Sauna 87D” x 81H”

saunalife-E8-Sauna-FIG2

Tools needed

saunalife-E8-Sauna-FIG3

installation

saunalife-E8-Sauna-FIG4

saunalife-E8-Sauna-FIG17

E8 Barrel Sauna 87D” x 81H”

saunalife-E8-Sauna-FIG5 saunalife-E8-Sauna-
FIG6

saunalife-E8-Sauna-FIG16

saunalife-E8-Sauna-FIG6

saunalife-E8-Sauna-FIG7 saunalife-E8-Sauna-
FIG8

saunalife-E8-Sauna-FIG18

saunalife-E8-Sauna-FIG11 saunalife-E8-Sauna-
FIG12 saunalife-E8-Sauna-FIG13saunalife-E8-Sauna-
FIG19

saunalife-E8-Sauna-FIG14

saunalife-E8-Sauna-FIG20 saunalife-E8-Sauna-
FIG15

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals