XO 6300 Scandomestic Built In Oven User Manual
- June 16, 2024
- scandomestic
Table of Contents
- XO 6300 Scandomestic Built In Oven
- Product Information
- Product Usage Instructions
- Product Introduction
- Functions
- Function Description
- FAQ
- IMPORTANT SAFETY INSTRUCTIONS
- DECLARATION OF COMPLIANCE
- PRODUCT INSTALLATION
- Door handle installation
- Knob installation
- Cupboard Diagram (Standing Cupboard)
- Installation Important Instructions
- Installation steps
- PRODUCT INTRODUCTION
- Accessories
- Control Panel
- Regular operation
- Cleaning and maintenance
- TROUBLESHOOTING
- SPECIFICATIONS
- PRODUCT RECYCLING
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
XO 6300 Scandomestic Built In Oven
Product Information
Specifications
- Brugbar volumen: 65L
- Nominel frekvens: 50Hz-60Hz
- Eleffekt: 3,2 kW
Product Usage Instructions
Product Installation
If there are differences between the illustration and the actual product,
refer to the actual product.
Knob Installation
(Only for some models) Mount the knob to the control panel.
Cabinet Diagram (Ground Cabinet)
Minimum bottom ventilation area: 250 mm2
- Reserve 5 mm for the door panel at the top and bottom respectively.
- Reserve 20 mm for the door panel on the left and right respectively.
- Reserve 20 mm for the door panel in thickness.
If the appliance is installed under the hob, the minimum thickness of countertop A is shown below:
Type of hob | Countertop A |
---|---|
Induction hob | 37 mm |
Full surface induction hob | 47 mm |
Gas hob | 30 mm |
Electric hob | 27 mm |
Product Introduction
- Oven
- Grill stand
- Grill food or place heat-resistant cooking containers
- Prepare large portions of food or catch leftovers
- Cut Remove the grill plate and grill grate
- Only for some models
- Small grill rack Prepare smaller portions of food
- Only for some models
Control panel
- A start
- B Remember
- C Time setting
- D Display
- E Stop
- K1: For selecting oven functions.
- K2: For setting the time.
- K3: For setting the temperature.
Functions
- Lamp Defrosting
- Double grill with fan
- Double grill Single grill
- Conventional + fan
- Conventional
- Bottom heating
Function Description
The cooking process can be observed under illuminated conditions. Except for the Pyrolytic function and ECO function.
Temperature and Time Settings
Conventional – 250°C, 0.5-1 hour
Turn knob K2 to adjust the time.
Lamp Replacement
Troubleshooting
Problem: Cannot Start
Contact after-sales service.
Problem : Food is not cooked
- The temperature is too low
- The food portion is too large
Adjust the cooking temperature or time.
Problem: The fan did not stop working after the heating stopped
Contact after-sales service.
FAQ
-
Q: How do I dispose of the product’s packaging?
A: Dispose of the product’s packaging correctly. Contact your dealer or manufacturer for details. -
Q: What materials are used in the product?
A: The product uses various materials including PE – polyethylen, PS – polystyren, PO M – polyoxymethylen, PP – polypropylen, and ABS – acrylonitril- butadien-styren. Contact your dealer or manufacturer for more details. -
Q: Can I use non-original spare parts?
A: To maintain the effectiveness and safety of the appliance, it is recommended to always use original spare parts and avoid using unauthorized personnel for repairs.
Warning notices: Before using this product, please read this manual
carefully and keep it for future reference. The design and specifications are
subject to change without prior notice for product improvement.
Consult with your dealer or manufacturer for details.
The illustration is for reference only, please refer to the actual product
appearance.
IMPORTANT SAFETY INSTRUCTIONS
THESE WARNINGS ARE PROVIDED IN THE INTEREST OF SAFETY. PLEASE READ THEM
CAREFULLY BEFORE INSTALLING OR USING THE APPLIANCE.
To maintain the EFFICIENCY and SAFETY of this appliance, we recommend
Call only the Service Centers authorized by store where you buy the cooker
Always use original Spare Parts
- When the oven is first switched on, it may give of an unpleasant smell. This is due to the bonding agent used for the insulating panels within the oven. Please run the new empty product with the conventional cooking function, 250°C, 90 minutes to clean oil impurities inside the cavity.
- During the first use, it is completely normal that there will be slight smoke and door. If it does occur, you should wait for the smell to be cleared before putting food into the oven.
- Please use the product under an open environment.
- The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised.
- If the surface is cracked, switch of the appliance to avoid the possibility of electric shock.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- During use, the appliance becomes very hot. Care should be taken to avoid touching heating elements inside the oven.
- Do not allow children to go near the oven when it is operating, especially when the grill is on.
- Ensure that the appliance is switched of before replacing the oven lamp to avoid the possibility of electric shock.
- The means for disconnection must be incorporated in the fixed wiring in accordance with the wiring specifications.
- Children should be supervised to ensure that they do not play with the appliance.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by person responsible for their safety.
- Accessible parts may become hot during use. Young children should be kept away.
- An all-pole disconnection means must be incorporated in the fixed wiring in accordance with the wiring rules.
- If the supply cord is damaged, it must be replaced by the manufactory, its service agent or similarly qualified persons in order to avoid a hazard.
- Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.
- Only use the temperature probe recommended for this oven.
- A steam cleaner is not to be used.
- The appliance is not intended to be operated by means of an external timer or a separate remote control system.
- Do not use the oven unless you are wearing something on your feet. Do not touch the oven with wet or damp hands or feet.
- For oven: Oven door should not be opened often during the cooking period.
- The appliance must be installed by an authorized technician and put into use. The producer is not responsible for any damage that might be caused by defective placement, and installation by unauthorized personnel.
- When the door or drawer of oven is open do not leave anything on it, or you may unbalance your appliance or break the door.
- Some parts of appliance may keep its heat for a long time; it is required to wait for it to cool down before touching onto the points that are exposed to the heat directly.
- If you will not use the appliance for a long time, it is advised to plug it of.
- Before activating the pyrolytic cleaning function, remove any excessive spillage and make sure that oven is empty. Do not leave anything inside it (e.g. pans, baking tray, dripping pan, slider bracket etc.) as this could heavily damage them.
DECLARATION OF COMPLIANCE
- When you have unpacked the oven, make sure that it has not been damaged in any way. If you have any doubts at all, do not use it: contact a professionally qualified person. Keep packing materials such as plastic bags, polystyrene, or nails out of the reach of children because these are dangerous to children.
PRODUCT INSTALLATION
If there is any differences between the illustration and the actual product, please refer to the actual product.
Door handle installation
Snap both ends of the door handle onto the two metal rings on the door glass.
Move the door handle parallel to the right so that the door handle is fully
seated on the oven door glass.
After installation, the handle will be centered with the door glass left and
right.
Knob installation
(Only for some models ) Mount the knob to the control panel.
Cupboard Diagram (Standing Cupboard)
A Air vents
B Minimum bottom ventilation area: 250 mm2
1 Reserve 5 mm for the door panel at the top and bottom respectively. 2
Reserve 20 mm for the door panel on the left and right respectively. Reserve
20 mm for the door panel in thickness.
- The thickness of the cupboard board is 20 mm.
- If the power socket is installed on the back of the appliance, the depth of the cupboard opening shall be increased from a minimum of 590 mm to 620 mm.
- The dimensions in the figures are in mm.
Cupboard Diagram (Ground Cupboard)
If the appliance is installed under the hob, the minimum thickness of worktop A is shown below:
Hob type | Worktop A |
---|---|
Induction hob | 37 mm |
Full-surface induction hob | 47 mm |
Gas hob | 30 mm |
Electric hob | 27 mm |
- Minimum bottom ventilation area: 250 mm2
- Reserve 5 mm for the door panel at the top and bottom respectively.
- Reserve 20 mm for the door panel on the left and right respectively.
- Reserve 20 mm for the door panel in thickness.
- The thickness of the cupboard board is 20 mm.
- If the power socket is installed on the back of the appliance, the depth of the cupboard opening shall be increased from a minimum of 590 mm to 620 mm.
- The dimensions in the figures are in mm.
Installation Important Instructions
Content that means [mandatory]
-
The safe operation of this appliance can only be guaranteed if it has been installed to a professional standard in accordance with these installation instructions. The installer shall be liable for any damage resulting from incorrect installation.
-
The entire installation process requires two professional installers. Wear dry protective gloves during installation to avoid scratch or electric shock.
-
Fitted units must be heat-resistant up to 90°C, and adjacent unit fronts up to 70°C.
-
Please use a 16A socket.
Content that means [prohibit] -
Do not install the appliance behind a decorative door or the door of a kitchen unit, as this may cause the appliance to overheat.
-
Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transit.
-
Do not block the vent of the appliance and the gap between the cupboard and the appliance.
-
Use extreme caution when moving or installing the appliance. It is very heavy, do not lift the appliance by the door handle.
-
If the power cord or power plug is damaged, stop using the appliance immediately, to avoid fire, electric shock or other injuries.
Content that means [note] -
Be very careful when moving or installing the appliance to avoid damage to the appliance or damage to the cupboards.
-
Before starting up the appliance, remove all packaging materials and accessories from the cavity.
-
The power socket shall be accessible to users (such as next to the cupboard) for easy power-of.
-
After installation is complete, make sure that the power plug is firmly inserted into the socket.
-
Please refer to the “Cupboard Diagram” for the requirements of net depth of the cupboard. The clearance between the cupboard bottom board and the rear board (or wall) shall not be less than 50 mm.
Installation steps
- Please customize the cupboard according to the “Cupboard Diagram”.
- Before installation, please check for normal power socket and appropriate grounding, and check whether the cupboard dimension meets the installation requirements.
- Place the appliance in designated locations in the kitchen, install it in a vertical cupboard, and connect the power supply.
- To locate the mounting fixing holes, open the appliance door and look at the side frame of the appliance (position shown above).
- Fix the appliance to the cupboard with two rubber plugs A and screws B provided with the appliance.
PRODUCT INTRODUCTION
Oven
When removing food, please wear heat insulating gloves to prevent burns!
At the moment of opening the door of the furnace, pay attention to the steam.
Please open the door at a small Angle to avoid the steam on your face.
- A Control panel
- B Mounting fixing hole
- C Handle
- D Ventilating openings
- E Mounting fixing hole
- F Glass door
Accessories
Grill rack
Grill food or place heat-resistant cooking containers
|
Cook large portions of food or catch food scraps
---|---
Clips
Remove the grill tray and grill rack Only for some models
| ****
Small grill rack
Cook smaller portions of food Only for some models
Grill rack
Accessories use(Only for some models)
For the oven to work properly, the grill rack and Grill tray should only be placed between the first and fifth levels. When used together, place the Grill tray under the grill rack.
Control Panel
- A Start
- B Remind
- C Time setting
- D Display
- E Stop
K1: For selecting oven functions. K2: For setting the time.
K3: For setting the temperature.
Function | Function Description |
---|
Lamp
| The cooking process can be observed under illuminated conditions. Except Pyrolytic function and ECO function.
Defrost
| The circulation of air at room temperature enables quicker thawing of frozen food (without the use of any heat).
Double grill with fan
| The radiant heating element and top heating element are working with fan.
Double grill
| The radiant heating element and top heating element are working. You can choose to use a rotating grill rack.
Single grill
| The inner grill element switches on and of to maintain temperature. Can be
used to grill a small number of food.
You can choose to use a rotating grill rack.
Conventional + fan
| The combination of fan and the top and bottom heating elements provides more even heat penetration and coloration, primarily for cooking meat.
Conventional
| The top and bottom heating elements work together to provide convectional cooking.
You can choose to use a rotating grill rack.
Bottom heating
| Heating is provided by heating pipes at the bottom of the oven. Mainly used for keeping warm and the coloring of the food.
Convection
| In convection mode, the fan turns on automatically to provide even heat for single or multi-layer baking. This is particularly suitable for baking foods that require even coloring.
ECO
| For energy-saving cooking. Cooking the selected ingredients in a gentle manner, and the heat comes from the top and the bottom.
Before using for the first time
- The oven must not be operated until it has been correctly installed.
- To avoid fire, remove all transport protection materials and ensure that the oven is free of residual packaging items and accessories (e.g. foam, cardboard, grill tray, grill rack, etc.).
- Clean the oven cavity and accessories with soapy water and a soft cloth.
- Open kitchen windows and cooker hoods to maintain high ventilation.
- Do not let children or pets into the kitchen and close the doors of adjacent rooms.
- After connecting the power, activate the oven mode, time, and temperature in the table below to remove odors in the cavity.
- After the first use, please open the oven door at a small angle and wait for the cooling to complete.
Function | Temperature | Time |
---|---|---|
Conventional |
250℃
|
0.5-1 Hour
Regular operation
Turn knob K1 to select the oven functions.
Turn knob K2 to adjust the time.
Turn knob K3 to adjust the temperature.
When cooking is finished, turn all knobs to the “O” position.
Cleaning and maintenance
Cleaning
Disconnect the power supply before cleaning and maintenance.
In order to ensure the life of the oven, it should be thoroughly cleaned
frequently. Cleaning steps are as follows:
- After cooking, wait for the oven to cool completely.
- Remove oven accessories, rinse with warm water and dry.
- Clean up food debris from the oven chamber.
- Wipe the oven with a soft cloth stained with detergent, then dry with a dry soft cloth.
Notes
- Do not use sharp cleaning tools, hard brush and corrosive cleaning products, so as not to damage the oven and its accessories.
- Do not use rough scrubbing agent or sharp metal spatula to clean the door glass.
Lamp Replacement
-
Switch of and disconnect the power from the oven. Ensure that the internal parts are cool before touching internal parts.
-
Remove the lamp cover by turning it counter-clockwise (note, it
may be stif), replace the bulb with a new one of the same type. -
Insert the new bulb, which should be resistant to 300°C. For replacement bulbs contact your local service center.
-
If in any doubt, consult a qualified electrician for help.
Warning
To avoid electric shocks-please ensure that the electricity supply to the
appliance is switched of and the appliance is fully cold. before removing the
lamp lens.
TROUBLESHOOTING
Problem | Possible reason | Solution |
---|---|---|
Unable to start | Power is not connected | connect power supply |
The main power switch is not turned on | Turn on the power switch | |
Oven door not closed | Close the oven door | |
lamp does not come on | It’s broken | Contact after-sales service |
Has a pungent odor or smoke | first use | No processing required |
Food is not cooked | Temperature is too low | Use a higher temperature |
Food portion is too large | Cook food in smaller pieces or extend the cooking |
time.
Burnt or uneven food| The temperature is set too high or the heating time is
too long| Adjust the cooking temperature or time
The food is too close to the heating tube| Adjust the placement layers of
accessories
The fan did not stop working after stopping the heating| Fan delays blowing
for heat dissipation| No processing required
If the problem cannot be solved or other problems occur, please contact the after- sales service.
SPECIFICATIONS
- Usable Volume:
- 65L
- Rated voltage:
- 220-240V~
- Rated frequency:
- 50Hz-60Hz
- Electric power:
- 3.2 kW
PRODUCT RECYCLING
This appliance is marked according to the European directive 2012/19/EU on
Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed correctly, you will help prevent
potential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product. The
symbol on the product indicates that this product may not be treated as
household waste. Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. Disposal must
be carried out in accordance with local environmental regulations for waste
disposal. For more detailed information about treatment, recovery and
recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the product.
This symbol on the product or instruction manual indicates that your device
should be disposed of separately from your household waste at the end of its
useful life.
There is a separate recycling system locally for recycling. For more
information, please contact the local authority or retailer where you
purchased the product.
When you have unpacked the oven, make sure that it has not been damaged in any way. If you have any doubts at all, do not use it: contact a professionally qualified person. Keep packing materials such as plastic bags, polystyren, or nails out of the reach of children because these are dangerous to children.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>