Aerpro CAVW01 Volkswagen Scirocco Instruction Manual

Aerpro CAVW01 Volkswagen Scirocco

Product Information

Specifications

• Compatible with select Volkswagen vehicles:
  • Volkswagen EOS (2009 – 2016)
  • Volkswagen Golf (2008 – 2013)
  • Volkswagen Multivan (2010 – 2015)
  • Volkswagen Passat* (2010 – 2015)
  • Volkswagen Polo (2009 – 2014)
  • Volkswagen Scirocco (2011 – 2015)
  • Volkswagen Sharan (2010 – 2015)
  • Volkswagen Tiguan (2011 – 2015)
  • Volkswagen Touran (2010 – 2015)
• Compatible only with models with White MFD
• Compatible with Fender OEM Amplified System

About

The Connects2 Infodapter for VW vehicles allows vehicle information such as climate control, parking sensors, and heated seats to be displayed on any aftermarket head unit with rear camera input. The Infodapter also allows the use of the steering wheel controls with almost every steering wheel control compatible head unit on the market.

Dip Switch Settings

1. Reverse Camera output to the head unit and reverse camera input from optional camera
2. Power Harness
3. Steering Wheel Remote control connector to head unit
4. Dip Switches Not Used

Steering Wheel Controls

B/C Track Up/Down

Configuration Menu

To access the menu, push and hold the speech button for 2 seconds (Fig. 3). This will enable the configuration menu. To navigate through the menu options, use the Track Up/Track Down buttons. To select a menu option, push the speech button once.

Screen Size/Position

• Horizontal Size
• Horizontal Position
• Vertical Size
• Vertical Position

Picture Settings

• Brightness
• Contrast
• Saturation

Vehicle Settings

• Driver Position – Select Left or Right depending upon vehicle configuration.

Amplifier Settings

Product Usage Instructions

Step 1: Vehicle Compatibility Check

Ensure that your Volkswagen vehicle is compatible with the CAVW01 Infodapter. Refer to the specifications section above for   the list of compatible models.

Step 2: Installation

1. Disconnect the negative terminal of your vehicle’s battery to prevent any electrical mishaps during installation.
2. Locate the Infodapter and connect the reverse camera output to the head unit and the reverse camera input from an optional camera.
3. Connect the power harness to the appropriate port.
4. Connect the steering wheel remote control connector to the head unit.
5. Ensure that all connections are secure and properly fitted.
6. Reconnect the negative terminal of your vehicle’s battery.

Step 3: Configuration

1. Push and hold the speech button for 2 seconds to access the configuration menu.
2. Use the Track Up/Track Down buttons to navigate through the menu options.
3. Push the speech button once to select a menu option.
4. Configure the screen size/position, picture settings, vehicle settings, and preferences according to your preferences.

FAQ

Q: Which Volkswagen models are compatible with the CAVW01 Infodapter?

A: The CAVW01 Infodapter is compatible with the following

• Volkswagen models: Volkswagen EOS (2009 – 2016), Volkswagen Golf
• (2008 – 2013), Volkswagen Multivan (2010 – 2015), Volkswagen Passat
• (2010 – 2015), Volkswagen Polo (2009 – 2014), Volkswagen Scirocco
• (2011 – 2015), Volkswagen Sharan (2010 – 2015), Volkswagen Tiguan
• (2011 – 2015), Volkswagen Touran (2010 – 2015). Please note that it is only compatible with models with White MFD and Fender OEM Amplified System.

Q: Can I use the steering wheel controls with any aftermarket head unit?

A: Yes, the Infodapter allows the use of the steering wheel controls with almost every steering wheel control compatible head unit on the market.

ABOUT

The Connects2 Infodapter for VW vehicles allows vehicle information such as climate control, parking sensors, and heated seats to be displayed on any aftermarket head unit with a rear camera input. The Infodapter also allows the use of the steering wheel controls with almost every steering wheel control compatible head unit on the market.

DIP SWITCH SETTINGS

See Fig 1. Up = Off, Down = On

1. On = Pioneer head units. Off = All other head units
2. Setting for reverse camera. On = PAL, Off = NTSC. The default setting is Off (NTSC).
3.  Resetsthe display settingsback to default. If the display settings have been manipulated in a way that it is no longer possible to make adjustments, change the DIP switch #3 from Off to On and back. This will reset the screen settings to the factory defaults. During this procedure, the screen background will change to red. While the background isred, no settings can be made.
4. Not applicable

INTERFACE CONNECTIONS

STEERING WHEEL CONTROLS

• À Speech Button
• B/CTrack Up/Down

CONFIGURATION MENU

To access the menu, push and hold the speech button for 2 seconds (Fig. 3). This will enable the configuration menu. To navigate through the menu optionsuse the Track Up/Track Down buttons. To select a menu option, push the speech button once.

• Screen Size/Position
  Make sure all 4 corner markers are touching the corner of the aftermarket head unit display.

• Picture Settings
  Adjust brightness, contrast, and color saturation.

CONFIGURATION MENU

Vehicle Settings

• Driver Position – Select Left or Right depending upon vehicle configuration.

• Amplifier Settings This setting can be used to adjust the gain of the aftermarket head unit, to match the OEM amplifier volume. (*Note this option is only available when an OEM amplifier is detected in the vehicle)

• Preferences
  Park Assist Version – Select according to the color configuration of the park assist fitted to the vehicle. Camera Connected – Select Yesif an optional camera is disconnected.
  Reverse Priority** – Select which image (Camera or Park Assist) will be shown by default when reversing. The driver can select the desired image by pushing the Speech button (Fig.3) while reversing. (Note this option is only available when Camera Connected is set to Yes) Park Brake Source – Set to one of the following: Brake – Park brake output active when park brake is on. Speed – Park brake output active when speed is less than 3KMH
  AlwaysOn – Park brake output is always active.
  Restore factory settings** – Reverts all Infodapter settings to factory defaults.(This does not restore vehicle settings)

Technical Support

If you need assistance setting up or using your Aerpro product now or in the future, call Aerpro Support Australia
TEL: 03 – 8587 8898 FAX: 03 – 8587 8866 Mon-Fri 9 am – 5 pm AEST. If you would like to download a digital copy of this manual, or other Aerpro manuals/software, please visit the http://aerpro.com website.

References

• Home | Aerpro
• Home | Aerpro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>