KICHLER 82413 Birk Mini Pendant Installation Guide

KICHLER 82413 Birk Mini Pendant

Product Information

• Item Number: 5336449
• Product Name: Birk Mini Pendant
• Model Number: 82413

Specifications

• Canopy: 1 piece
• Mounting Bracket: 1 piece
• Threaded Nipple: 1 piece
• Hex Nut: 3 pieces
• Socket Base: 1 piece
• Coupling: 1 piece
• Threaded Pipe: 1 piece
• Screw Collar Ring: 1 piece
• Screw Collar Loop: 1 piece
• Loop: 1 piece
• Chain: 1 piece
• Glass Shade: 1 piece
• Socket Ring: 1 piece
• Socket: 1 piece
• Wire Connector: 3 pieces
• Short Machine Screw: 2 pieces

Safety Information
Please read and understand this entire manual before attempting to assemble, operate, or install the product. This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to http://www.P65Warnings.ca.gov. Do not modify the product, take any parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate ETL listing and/or CSA certification of this fixture.

Product Usage Instructions

Preparation
Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

• Estimated assembly time: 30 minutes to 1 hour

Tools Required for Assembly (not included):

• Phillips screwdriver
• Flathead screwdriver
• Wire strippers
• Electrical tape
• Ladder
• Safety glasses
• Pliers (2)

Assembly Instructions

• Step 1:
  Screw threaded pipe (G) (with loop (J) preinstalled) into coupling (F). NOTE: The electrical cable will need to get pulled through the individual parts as they are installed on this and later steps.

• Step 2:
  Position threaded nipple (C) in mounting bracket (B) so that, when mounted:
  NOTE: A canopy is only needed to determine the position of the threaded nipple and screw collar loop. It will be installed later.

• Step 3:
  Once the proper position of the threaded nipple (C) and mounting bracket (B) has been determined, secure with hex nuts (D) as follows:

• Step 4:
  Connect mounting bracket (B) to the outlet box (not included) with short machine screws (BB).

• Step 5a:

• To open chain links:
  Locate the split in the chain link (K) you’re removing. Put one pair of pliers (not included) on each side of the split and rotate the pliers in opposite directions to open the link’s split. The open link should be shaped like the letter C.

• Step 5b:
  Do not twist the ends of the link sideways so that the open link cannot lay flat.

• Step 6:
  Thread chain (K) through screw collar ring (H) and canopy (A). Using the open chain links on chain (K), attach one end to the screw collar loop (I) and the other loop end (J). Weave the electrical fixture and ground wires through every other chain link and pass through threaded nipple (C) into the outlet box. Lower the screw collar ring (H) and canopy (A) over the chain (K).

NOTE:
Add or remove chain links once the desired length is established. Trim extra cabling, leaving six inches of extra wire protruding from the screw collar loop and threaded nipple.

FAQs

• Q: What should I do if any parts are missing or damaged?
  A: If any part is missing or damaged, do not attempt to assemble the product. Please contact our customer service department at 1-800-554-6504, 8 am – 4:30 pm, EST, Monday – Friday.

• Q: Can I modify or use worn-out/broken parts of the product?
  A: No, modifying the product or using worn-out/broken parts could invalidate the ETL listing and/or CSA certification of this fixture. Do not modify the product, take any parts out, or use any parts that are worn out or broken.

• Q: How long is the estimated assembly time?
  A: The estimated assembly time is between 30 minutes to 1 hour.

PACKAGE CONTENTS

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

WARNING

• CAUTION – RISK OF SHOCK –
  Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

• WARNING:
  This fixture is intended for installation by the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.

• Do not use bulbs with wattage greater than specified on this fixture.

• California Proposition 65
  WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to http://www.P65Warnings.ca.gov.

CAUTION

• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate the ETL listing and/or C.S.A. certification of this fixture.

PREPARATION

Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated assembly time: 30 minutes to 1 hour
Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses, and pliers (2).

ASSEMBLY INSTRUCTIONS

• 1. Screw-threaded pipe (G) (with loop (J) preinstalled) into coupling (F).
  NOTE: The electrical cable will need to get pulled through the individual parts as they are installed on this and later steps.

• 2. Position threaded nipple (C) in mounting bracket (B) so that, when mounted:

  • The threaded nipple (C) will protrude a minimum of 1/4 inch beyond the raised center portion of the bracket (B).
  • The threaded nipple (C) height should be positioned so that 1/2 the exterior threads of the screw collar loop (I) will extend past the canopy (A) when it is mounted.
    NOTE: A canopy is only needed to determine the position of the threaded nipple and screw collar loop. It will be installed later.

• 3. Once the proper position of the threaded nipple (C) and mounting bracket (B) has been determined, secure with hex nuts (D) as follows:

  • Screw one hex nut (D) onto the threaded nipple (C) and tighten against the raised portion of the mounting bracket (B).
  • Screw another hex nut (D) onto the threaded nipple (C) and tighten it against the flat portion of the mounting bracket (B).
  • Screw the remaining hex nut (D) onto the threaded nipple (C) and tighten it against the screw collar loop (I).

• 4. Connect mounting bracket (B) to the outlet box (not included) with short machine screws (BB).
  Hardware Used

• 5a. To open chain links:
  Locate the split in the chain link (K) you’re removing. Put one pair of pliers (not included) on each side of the split and rotate the pliers in opposite directions to open the link’s split. The open link should be shaped like the letter “C”.

• 5b. Do not twist the ends of the link sideways so that the open link cannot lay flat.

• 6. Thread chain (K) through screw collar ring (H) and canopy (A). Using the open chain links on chain (K), attach one end to the screw collar loop (I) and the other loop end (J). Weave the fixture electrical and ground wires through every other chain link and pass through threaded nipple (C) into the outlet box. Lower the screw collar ring (H) and canopy (A) over the chain (K).
  NOTE: Add or remove chain links once the desired length is established. Trim extra cabling leaving six inches of extra wire protruding from the screw collar loop and threaded nipple.
  CAUTION: To avoid damage from falling, make sure the open chain links are fully closed once assembled.

• 7. Wire connection guide:
  Ground wire:

  • For installation in the United States: Wrap ground wire from outlet box around ground screw preassembled on mounting bracket (B) no less than 2 in. from wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect to the outlet ground wire with a wire connector (AA).

  • For installation in Canada: If the fixture is supplied with ground wire, wrap ground wire around the ground screw on the mounting bracket (B). Tighten the ground screw. Connect fixture ground wire to outlet ground wire with a wire connector (AA).
    Supply wires:

  • Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord “D” shaped and ribbed).

  • Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth). NOTE:
    Fixture wires will either be:

  • Black and White.

  • Parallel Cord SPT-1 lamp wire with one round smooth wire and one “D” shaped ribbed wire.
    Hardware Used

• 8. Pass canopy (A) over the screw collar loop (I).

  • Attach screw collar ring (H) to screw collar loop (I) to secure canopy (A).
  • NOTE: Make sure all wires are inside of canopy (A) and do not get pinched between canopy (A) and mounting bracket (B), or canopy (A) and ceiling.

• 9. Carefully pass the small opening in the glass shade (L) over socket (N), and seat glass shade (L) on socket base (E). While holding glass shade (L) in place, thread socket ring (M) onto threads of socket (N). Tighten socket ring (M) to secure glass shade (L) in place. DO NOT OVER-TIGHTEN.

• 10. Insert 60-watt max. medium-base bulb or LED equivalent (not included) into the socket (N).

CARE AND MAINTENANCE

• Always be certain that the electric current is turned off before cleaning this item.
• Use a soft, moist cloth with mild non-abrasive soap to clean the fixture. Never use glass cleaner on fixtures, as it will damage the metal finish.
• All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher.

TROUBLESHOOTING

2.   Worn or broken bulb.

| 1.  Check wiring.

2.   Replace bulb.

Distributed by:
Kichler Lighting LLC 30455 Solon Rd Solon, OH 44139 Printed in China.

Questions, problems, missing parts

Before returning to your retailer, call our customer service department at 1-800-554-6504, 8 a.m. – 4:30 p.m., EST, Monday – Friday. kichler.com/customer-care/contact- us.

References

• Our Locations | Kichler Lighting
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>