KICHLER 82408 Clove 4 Light Black Vintage Led Dry Rated Chandelier Instruction Manual

KICHLER 82408 Clove 4 Light Black Vintage Led Dry Rated Chandelier

Product Information

Specifications :

• Item #: 5336436
• Model #: 82408
• Number of Lights: 4
• Type: Linear Chandelier

Package Contents:

Hardware Contents:

• Wire Connector – Qty: 3
• Short Machine Screw – Qty: 2
• Threaded Knob – Qty: 2
• Long Machine Screw – Qty: 2
• Lock Washer – Qty: 2

Safety Information:

• Please read and understand this entire manual before attempting to assemble, operate, or install the product. This product contains chemicals, including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit http://www.P65Warnings.ca.gov.
• Do not leave out any parts or use any worn-out or broken parts, as it may invalidate the ETL listing and/or C.S.A. certification of this fixture.

Product Usage Instructions

Preparation:
Before beginning assembly of the product, ensure that all parts are present. Compare the parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated assembly time: 30 minutes to 1 hour

Tools Required for Assembly (not included):

• Phillips screwdriver
• Flathead screwdriver
• Wire strippers
• Electrical tape
• Ladder
• Safety glasses
• Pliers (2)

Assembly Instructions:

1. Step 1:
   Screw the 12-inch threaded pipe (G) into the coupling (H). Next, screw the 6-inch threaded pipe (F) into the 12-inch threaded pipe (G). Finally, screw the fixture loop (D) into the 6-inch threaded pipe (F). Repeat this step on the other side of the fixture.

2. _ Note: The electrical cable will need to be pulled through _the individual parts as they are installed in this and later steps.

3. Step 2:
   Using the open chain links (C), connect the fixture loops (D) to the loops on the canopy (A).

4. Caution: To avoid damage from falling, make sure the open chain links are fully closed once assembled.

5. Step 3:
   Orient the mounting bracket (B) so that the raised center portion protrudes into the outlet box (not included). Insert the long machine screws (DD) through the mounting bracket (B) so that the long machine screws (DD) protrude downward. Connect the mounting bracket (B) to the outlet box with the short machine screws (BB).

Step 4:
Connect the supply wires and fixture wires according to the following diagram:

BARE COPPER, OR GREEN GROUND SUPPLY WIRE
BLACK SUPPLY WIRE
WHITE SUPPLY WIRE
BLACK SUPPLY WIRE
WHITE SUPPLY WIRE
BARE COPPER, OR GREEN GROUND FIXTURE WIRE
BLACK FIXTURE WIRE
WHITE FIXTURE WIRE
OR PARALLEL FIXTURE CORD (ROUND AND SMOOTH)
PARALLEL FIXTURE CORD (D SHAPED AND RIDGED)

FAQ:

• Q: What do I do if a part is missing or damaged?
  A: If any part is missing or damaged, do not attempt to assemble the product. Contact our customer service department at 1-800-554-6504 for assistance.

• Q: What are the safety precautions for this product?
  A: Please read and understand the entire manual before attempting to assemble, operate, or install the product. Ensure that you do not leave out any parts or use any worn-out or broken parts, as it may invalidate the ETL listing and/or C.S.A. certification of this fixture.

• Q: How do I adjust the hanging height of the chandelier?
  A: The hanging height of this fixture is adjustable. You can add or subtract threaded pipes (G) to achieve the desired height.

CLOVE 4-LIGHT LINEAR CHANDELIER
MODEL #82408

ATTACH YOUR RECEIPT HERE

• Serial Number__
• Purchase Date__

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-554-6504, 8 a.m. – 4:30 p.m, EST, Monday – Friday. kichler.com/customer-care/contact-us

PACKAGE CONTENTS

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

• CAUTION – RISK OF SHOCK –
  Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

• WARNING :
  This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.

• Do not use bulbs with wattage greater than specified on this fixture.

• California Proposition 65

• WARNING : This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm.

• For more information, go to http://www.P65Warnings.ca.gov

CAUTION

• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate ETL listing and/or C.S.A. certification of this fixture.

PREPARATION

• Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
• Estimated assembly time: 30 minutes to 1 hour
• Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses, pliers (2).

ASSEMBLY INSTRUCTIONS

1. Screw 12 inch threaded pipe (G) into coupling (H). Next, screw 6 inch threaded pipe (F) into 12 inch threaded pipe (G). Finally, screw fixture loop (D) into 6 inch threaded pipe (F).
   Repeat on other side of fixture.

2. NOTE: The electrical cable will need to get pulled through the individual parts as they are installed on this and later steps.

3. NOTE: The hanging height for this fixture is adjustable. Add or subtract threaded pipes to achieve the desired height.

4. Using the open chain links (C), connect fixture loops (D) to loops on canopy (A).
   CAUTION: To avoid damage from falling, make sure the open chain links are fully closed once assembled.

5. Orient the mounting bracket (B) so the raised center portion protrudes into the outlet box (not included). Insert long machine screws (DD) through mounting bracket (B) so the long machine screws (DD) protrude downward. Connect the mounting bracket (B) to the outlet box with short machine screws (BB). Hardware Used

6. Wire connection guide:
   Ground wire:

   • For installation in the United States: Wrap ground wire from outlet box around ground screw preassembled on mounting bracket (B) no less than 2 in. from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA).

   • For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around ground screw on mounting bracket (B). Tighten ground screw. Connect fixture ground wire to outlet ground wire with a wire connector (AA).
     Supply wires:

   • Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord “D” shaped and ribbed).

   • Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth).

   • Hardware Used

   • NOTE:

   • Fixture wires will either be:

   • Black and White.

   • Parallel Cord SPT-1 lamp wire with one round smooth wire and one “D” shaped ribbed wire.

7. Pass canopy (A) over the long machine screws protruding from mounting bracket (B) and secure with lock washers (EE) and threaded knobs (CC).
   NOTE: Make sure all wires are inside of canopy (A) and do not get pinched between canopy (A) and mounting bracket (B), or canopy (A) and ceiling.

   • Hardware Used
   • NOTE : The bottom edge of an outlet box should be flush with the bottom surface of a ceiling. However, many boxes are recessed into the ceiling. The long machine screws (DD) are designed to have extra length to accommodate to various box depths.
   1. The long machine screws (DD) may, at first, protrude too far past the surface of the canopy (A).
   2. Screw the threaded knobs (CC) onto the long machine screws (DD). The screws will back thread into the mounting bracket (B) until the canopy (A) is tight against the ceiling.

8. Carefully pass small opening in glass shade (I) over socket (E), and seat glass shade (I) on socket base (K). While holding glass shade (I) in place, thread socket ring (J) onto threads of socket (E). Tighten socket ring (J) to secure glass shade (I) in place. DO NOT OVER-TIGHTEN. Repeat for remaining glass shades (I).

9. Insert 60-watt max. medium-base bulb or LED equivalent (not included) into socket (E). Repeat for remaining sockets (E).

CARE AND MAINTENANCE

• Always be certain that electric current is turned off before cleaning this item.
• Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish.
• All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher.

TROUBLESHOOTING

1. Fixture may be wired incorrectly.
2. Worn or broken bulb.

|

1. Check wiring.
2. Replace bulb.

References

• Our Locations | Kichler Lighting
• p65warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>