KICHLER 38272 Jaylen 3 Light Flush Mount Ceiling Fixture Instruction Manual
- June 15, 2024
- KICHLER
Table of Contents
KICHLER 38272 Jaylen 3 Light Flush Mount Ceiling Fixture
Product Information
Specifications
- Item Number: 5336453
- Model Number: 38272
- Fixture Type: Flush Mount Ceiling Fixture
- Number of Lights: 3
Safety Information
Please read and understand this entire manual before attempting to assemble,
operate, or install the product. Failure to follow these instructions may
result in damage or injury.
WARNING:
This product can expose you to chemicals including lead, which is known to the
State of California to cause cancer, birth defects, or other reproductive
harm. For more information, go to http://www.P65Warnings.ca.gov
Preparation
Before beginning assembly of the product, make sure all parts are present.
Compare the parts with the package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
- Estimated Assembly Time: 30 minutes to 1 hour
Tools Required for Assembly (not included):
- Phillips screwdriver
- Flathead screwdriver
- Wire strippers
- Electrical tape
- Ladder
- Safety glasses
Assembly Instructions
Step 1: Mounting Bracket Installation
- Insert the long machine screws (DD) through the mounting bracket (B) so that the screws protrude outward.
- Orient the mounting bracket (B) so that the raised center portion protrudes into the outlet box (not included).
- Connect the mounting bracket (B) to the outlet box using the short machine screws (BB).
Step 2: Wiring
Refer to the provided diagram for wiring instructions.
Supply Wire Connections:
- Black Supply Wire – Connect to Black Fixture Wire or Parallel Fixture Cord (Round and Smooth)
- White Supply Wire – Connect to White Fixture Wire or Parallel Fixture Cord (D Shaped and Ridged)
- Bare Copper or Green Ground Supply Wire – Connect to Bare Copper or Green Ground Fixture Wire
Step 3: Canopy Installation
- Pass the canopy (A) over the long machine screws (DD) protruding from the mounting bracket (B).
- Secure the canopy (A) in place with the lock washers (EE) and threaded knobs (CC).
- Make sure all wires are inside the canopy (A) and do not get pinched between the canopy (A) and mounting bracket (B), or canopy (A) and ceiling.
Note:
The bottom edge of an outlet box should be flush with the bottom surface of a
ceiling. However, many boxes are recessed into the ceiling. The long machine
screws (DD) are designed to have extra length to accommodate various box
depths.
- The long machine screws (DD) may initially protrude too far past the surface of the canopy (A).
- Screw the threaded knobs (CC) onto the long machine screws (DD). The screws will back thread into the mounting bracket (B) until the canopy (A) is tight against the ceiling.
FAQ
-
Q: What should I do if a part is missing or damaged?
A: If any part is missing or damaged, do not attempt to assemble the product. Please contact our customer service department at 1-800-554-6504 for assistance. -
Q: Can I use this product with a recessed outlet box?
A: Yes, the long machine screws (DD) are designed to accommodate various box depths, including recessed outlet boxes. -
Q: Can I install this product myself?
A: Yes, this product can be installed by following the provided assembly instructions. However, if you are unsure or uncomfortable with the installation process, we recommend consulting a professional electrician.
PACKAGE CONTENTS
| PART | DESCRIPTION | QTY. |
|---|---|---|
| A | Canopy | 1 |
| B | Mounting Bracket | 1 |
| C | Socket | 3 |
| D | Socket Base Cup | 3 |
| --- | --- | --- |
| E | Socket Ring | 3 |
| F | Glass Shade | 3 |
HARDWARE CONTENTS
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before
starting and during the installation.
WARNING:
This fixture is intended for installation in accordance with the National
Electrical Code (NEC) and all local code specifications. If you are not
familiar with code requirements, installation by a certified electrician is
recommended.
- Do not use bulbs with wattage greater than specified on this fixture.
- California Proposition 65
WARNING:
This product can expose you to chemicals including lead, which is known to the
State of California to cause cancer, birth defects, or other reproductive
harm. For more information, go to http://www.P65Warnings.ca.gov.
CAUTION
- If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate ETL listing and/or C.S.A. certification of this fixture.
PREPARATION
Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated assembly time: 30 minutes to 1 hour
Tools Required for Assembly (not included): Phillips screwdriver, flathead
screwdriver, wire strippers, electrical tape, ladder, and safety glasses.
ASSEMBLY INSTRUCTIONS
-
1. Insert long machine screws (DD) through mounting brackets (B) so the long machine screws (DD) protrude outward. Orient the mounting bracket (B) so the raised center portion protrudes into the outlet box (not included). Connect the mounting bracket (B) to the outlet box with short machine screws (BB).
Hardware Used -
2. Wire connection guide:
Ground wire:-
For installation in the United States: Wrap ground wire from outlet box around ground screw preassembled on mounting bracket (B) no less than 2 in. from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA).
-
For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around ground screw on mounting bracket (B). Tighten ground screw. Connect fixture ground wire to outlet ground wire with a wire connector (AA).
Supply wires: -
Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord “D” shaped and ribbed).
-
Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth).
Hardware Used NOTE:
Fixture wires will either be: -
Black and White.
-
Parallel Cord SPT-1 lamp wire with one round smooth wire and one “D” shaped ribbed wire.
-
-
3a. Pass canopy (A) over the long machine screws (DD) protruding from the mounting bracket (B) and secure in place with lock washers (EE) and threaded knobs (CC).
NOTE: Make sure all wires are inside of canopy (A) and do not get pinched between canopy (A) and mounting bracket (B), or canopy (A) and ceiling.
Hardware Used -
3b. NOTE: The bottom edge of an outlet box should be flush with the bottom surface of a ceiling. However, many boxes are recessed into the ceiling. The long machine screws (DD) are designed to have extra length to accommodate to various box depths.
- The long machine screws (DD) may, at first, protrude too far past the surface of the canopy (A).
- Screw the threaded knobs (CC) onto the long machine screws (DD). The screws will back thread into the mounting bracket (B) until the canopy (A) is tight against the ceiling.
-
4. Carefully slip small opening in glass shade (F) up over socket (C) until it is seated in the socket base cup (D). While holding glass shade (F) in place, thread socket ring (E) onto threads of socket (C). Tighten socket ring (E) to secure glass shade (F) in place. DO NOT OVER-TIGHTEN. Repeat for remaining glass shades (F).
-
5. Insert 60-watt max. medium base bulb or LED equivalent (not included) into the socket (C). Repeat for remaining sockets (C).
CARE AND MAINTENANCE
- Always be certain that the electric current is turned off before cleaning this item.
- Use a soft, moist cloth with mild non-abrasive soap to clean the fixture. Never use glass cleaner on fixtures, as it will damage the metal finish.
- All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher.
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| The fixture does not light. | 1. Fixture may be wired incorrectly. |
2. Worn or broken bulb.
| 1. Check wiring.
2. Replace bulb.
Distributed by:
Kichler Lighting LLC 30455 Solon Rd Solon, OH 44139 Printed in India.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>