KICHLER 82414 Jaylen 3 Light Pendant Instructions

: June 15, 2024
: KICHLER

Table of Contents

KICHLER 82414 Jaylen 3 Light Pendant
PACKAGE CONTENTS
HARDWARE CONTENTS
SAFETY INFORMATION
PREPARATION
ASSEMBLY INSTRUCTIONS
CARE AND MAINTENANCE
TROUBLESHOOTING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KICHLER 82414 Jaylen 3 Light Pendant

Product Information

Item Number: 5336451, 5336452
Product Name: JAYLEN 3-LIGHT PENDANT
Model Number: 82414, 82415

Specifications

Canopy: Quantity: 1
Mounting Bracket: Quantity: 1
Socket Ring: Quantity: 3
Glass Shade: Quantity: 3
Cord (preassembled to Canopy): Quantity:3
Socket (preassembled to Cord): Quantity: 3
Compression Fitting (preassembled to Canopy): Quantity: 3
Socket Base Cup: Quantity: 3

Safety Information

Please read and understand this entire manual before attempting to assemble, operate, or install the product. This product contains chemicals, including lead, which is known to the State of
California to cause cancer, birth defects, or other reproductive harm. For more information, visit http://www.P65Warnings.ca.gov.
Do not leave out any parts or use worn-out or broken parts as it may invalidate ETL listing and/or C.S.A. certification of this fixture.

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

A| Canopy| 1
B| Mounting Bracket| 1
C| Socket Ring| 3
D| Glass Shade| 3
E| Cord (preassembled to Canopy (A))| 3
F| Socket (preassembled to Cord (E))| 3
G| Compression Fitting (preassembled to Canopy (A))| 3
H| Socket Base Cup| 3

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.
WARNING

This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
Do not use bulbs with wattage greater than specified on this fixture.

California Proposition 65
WARNING : This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm.
For more information, go to http://www.P65Warnings.ca.gov

CAUTION

If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate ETL listing and/or C.S.A. certification of this fixture.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated assembly time: 30 minutes to 1 hour
Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses.

ASSEMBLY INSTRUCTIONS

The hanging length of each cord (E) for this fixture is adjustable. Hold the canopy (A) up against the ceiling and determine the desired length for each cord (E) before the fixture is assembled.
Loosen the compression fitting (G) to release the cord (E) as needed to achieve the desired height. Then, screw the compression fitting (G) back into place to secure cord (E).
Set fixture aside for now.
Insert long machine screws (DD) through mounting bracket (B) so the long machine screws (DD) protrude outward. Orient the mounting bracket (B) so the raised center portion protrudes into the outlet box (not included). Connect the mounting bracket (B) to the outlet box with short machine screws (BB).
Hardware Used
Wire connection guide:
Ground wire
- For installation in the United States: Wrap ground wire from outlet box around ground screw preassembled on mounting bracket
  (B) no less than 2 in. from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA).
- For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around ground screw on mounting bracket (B). Tighten ground screw. Connect fixture ground wire to outlet ground wire with a wire connector (AA).
  Supply wires:
- Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord “D” shaped and ribbed).
- Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth).
  Hardware Used
4a. Pass canopy (A) over the long machine screws protruding from mounting bracket (B) and secure with lock washers (EE) and threaded knobs (CC).
NOTE : Make sure all wires are inside of canopy (A) and do not get pinched between canopy (A) and mounting bracket (B), or canopy (A) and ceiling.

4b.NOTE: The bottom edge of an outlet box should be flush with the bottom surface of a ceiling. However, many boxes are recessed into the ceiling. The long machine screws (DD) are designed to have extra length to accommodate to various box depths.

1. The long machine screws (DD) may, at first, protrude too far past the surface of the canopy (A).
2. Screw the threaded knobs (CC) onto the long machine screws (DD). The screws will back thread into the mounting bracket (B) until the canopy (A) is tight against the ceiling.

Carefully slip small opening in glass shade (D) up over socket (F) until it is seated in socket base cup (H). While holding glass shade (D) in place, thread socket ring (C) onto threads of socket (F). Tighten socket ring (C) to secure glass shade (D) in place. DO NOT
OVER-TIGHTEN.
Repeat for remaining glass shades (D).
Insert 60-watt max. medium base bulb or LED equivalent (not included) into socket (F). Repeat for remaining sockets (F).

CARE AND MAINTENANCE

Always be certain that electric current is turned off before cleaning this item.
Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish.
All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher.