KICHLER 82412 Birk 4 Light Matte Black Rustic Led Dry Instruction Manual

KICHLER 82412 Birk 4 Light Matte Black Rustic Led Dry

Product Information

Specifications

• Item number: 5336448
• Model: 82412

Package Contents

• Canopy (Qty: 1)
• Mounting Bracket (Qty: 1)
• Canopy Loop (preassembled) (Qty: 1)
• Chain (Qty: 2)
• Socket Fixture Loop (Qty: 2)
• Threaded Pipe (Qty: 2)
• Coupling (Qty: 2)
• Glass Shade Socket  Ring (Qty: 4)
• Socket Base (Qty: 4)

Hardware Contents

• Wire Connector (Qty: 3)
• Short Machine Screw (Qty : 2)
• Threaded Knob (Qty : 2)
• Long Machine Screw (Qty : 2)
• Lock Washer (Qty: 2)

Safety Information

Please read and understand this entire manual before attempting to assemble, operate, or install the product. This product contains chemicals, including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit www.P65Warnings.ca.gov. Do not leave out parts or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL listing and/or C.S.A. certification of this fixture.

Product Usage Instructions

Preparation

• Before beginning assembly of the product, make sure all parts are present. Compare the parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
• Estimated assembly time: 30 minutes to 1 hour

Tools Required for Assembly (not included):

• Phillips screwdriver
• Flathead screwdriver
• Wire strippers
• Electrical tape
• Ladder
• Safety glasses
• Pliers (2)

Assembly Instructions

Step 1: Threaded Pipe and Fixture Loop

1. Screw threaded pipe (G) into coupling (H).
2. Screw fixture loop (F) into threaded pipe (G).

Step 2: Opening Chain Links

1. Locate the split in the chain link (D).
2. Put one pair of pliers on each side of the split and rotate the pliers in opposite directions to open the link’s split. The open link should be shaped like the letter C.
3. Do not twist the ends of the link sideways so that the open link cannot lay flat.

Step 3: Connecting Canopy Loops, Fixture Loops, and Chain

• Connect the canopy loops (C) to the fixture loops (F) using chain (D). Be sure to weave the electrical cable through the chain for the best appearance.
• Add or remove chain links once the desired length is established.
• Ensure that the open chain links are fully closed to avoid damage from falling.

Step 4: Mounting Bracket and Outlet Box

1. Orient the mounting bracket (B) so the raised center portion protrudes into the outlet box (not included).
2. Insert long machine screws (DD) through the mounting bracket (B) so that they protrude downward.
3. Connect the mounting bracket (B) to the outlet box with short machine screws (BB).

Electrical Wiring

• Bare copper or green ground supply wire
• Black supply wire

FAQ

Q: What should I do if I am missing parts or if any part is damaged?

• A: If you are missing parts or if any part is damaged, do not attempt to assemble the product. Please contact our customer service department at 1-800-554-6504, 8 a.m. – 4:30 p.m., EST, Monday – Friday for assistance.

Q: Can I adjust the length of the chain?

• A: Yes, you can add or remove chain links once the desired length is established. However, ensure that the open chain links are fully closed to avoid damage from falling.

Q: What tools do I need for assembly?

• A: The tools required for assembly (not included) are a Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses, and pliers (2).

Q: Is this product safe to use?

• A: Yes, this product is safe to use. However, please read and understand the entire manual before attempting to assemble, operate, or install the product. Follow all safety instructions provided.

PACKAGE CONTENTS

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

WARNING

• CAUTION – RISK OF SHOCK
• Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING:

• This fixture is intended for installation by the National Electrical Code (NEC) and all local code specifications.
• If you are not familiar with code requirements, installation by a certified electrician is recommended.
• Do not use bulbs with wattage greater than specified on this fixture.

California Proposition 65

• WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm.
• For more information, go to http://www.P65Warnings.ca.gov

CAUTION

• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate ETL listing and/or C.S.A. certification of this fixture.

PREPARATION

• Before beginning assembly of a product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated assembly time: 30 minutes to 1 hour

• Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses, and pliers (2).

ASSEMBLY INSTRUCTIONS

1. Screw threaded pipe (G) into coupling (H). Next, screw the fixture loop (F) into threaded pipe (G).
   • NOTE: The electrical cable will need to get pulled through the individual parts as they are installed on this and later steps.
2. To open chain links:
   • Locate the split in the chain link (D). Put one pair of pliers (not included) on each side of the split and rotate the pliers in opposite directions to open the link’s split. The open link should be shaped like the letter “C”.
   • Do not twist the ends of the link sideways so that the open link cannot lay flat.
3. Connect the canopy loops (C) to the fixture loops (F) using chain (D)
   • NOTE: For best appearance be sure to weave the electrical cable through chain.
   • NOTE: Add or remove chain links once the desired length is established.
   • CAUTION: To avoid damage from falling, make sure the open chain links are fully closed once assembled.
4. Orient the mounting bracket (B) so the raised center portion protrudes into the outlet box (not included). Insert long machine screws (DD) through mounting brackets (B) so the long machine screws (DD) protrude downward. Connect the mounting bracket (B) to the outlet box with short machine screws (BB).
   • Hardware Used
5. Wire connection guide:
   • Ground wire
   • For installation in the United States: Wrap ground wire from outlet box around ground screw preassembled on mounting bracket (B) no less than 2 in. from wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect to the outlet ground wire with a wire connector (AA).
   • For installation in Canada: If the fixture is supplied with ground wire, wrap ground wire around the ground screw on the mounting bracket (B). Tighten ground screw. Connect fixture ground wire to outlet ground wire with a wire connector (AA).
   • Supply wires:
   • Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord “D” shaped and ribbed).
   • Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth).
   • Hardware Used
   • AA Wire Connector
   • NOTE: Fixture wires will either be
   • Black and White.
6. Parallel Cord SPT-1 lamp wire with one round smooth wire and one “D” shaped ribbed wire.
   • a. Pass canopy (A) over the long machine screws protruding from the mounting bracket (B) and secure with lock washers (EE) and threaded knobs (CC).
   • NOTE: Make sure all wires are inside of canopy (A) and do not get pinched between canopy (A) and mounting bracket (B), or canopy (A) and ceiling.
   • Hardware Used
   • b.NOTE : The bottom edge of an outlet box should be flush with the bottom surface of a ceiling. However, many boxes are recessed into the ceiling. The long machine screws (DD) are designed to have extra length to accommodate various box depths.
   • The long machine screws (DD) may, at first, protrude too far past the surface of the canopy (A).
   • Screw the threaded knobs (CC) onto the long machine screws (DD). The screws will back thread into the mounting bracket (B) until the canopy (A) is tight against the ceiling.
7. Carefully pass a small opening in glass shade (I) over a socket (E), and seat glass shade (I) on socket base (K). While holding glass shade (I) in place, thread socket ring (J) onto threads of socket (E). Tighten socket ring (J) to secure glass shade (I) in place.
   • DO NOT OVER-TIGHTEN.
   • Repeat for remaining glass shades (I).
8. Insert 60-watt max. medium-base bulb or LED equivalent (not included) into the socket (E). Repeat for remaining sockets (E).

CARE AND MAINTENANCE

• Always be certain that the electric current is turned off before cleaning this item.
• Use a soft, moist cloth with mild non-abrasive soap to clean the fixture. Never use glass cleaner on fixtures, as it will damage the metal finish.
• All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher.

TROUBLESHOOTING

2.  Worn or broken bulb.

| 1.  Check wiring.

2.  Replace bulb.

• Distributed by: Kichler Lighting LLC 30455 Solon Rd Solon, OH 44139 Printed in China
• Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-554-6504, 8 a.m. – 4:30 p.m, EST, Monday – Friday. kichler.com/customer-care/contact-us
• ATTACH YOUR RECEIPT HERE Serial Number————————-
• Purchase Date———————–

References

• Our Locations | Kichler Lighting
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>