Kichler 82410 Barrington 5 Light Distressed Black Farmhouse LED Chandelier Instruction Manual

Kichler 82410 Barrington 5 Light Distressed Black Farmhouse LED

Chandelier

Product Information

Specifications

• Item Number: 5336456
• Model Number: 82410

Frequently Asked Questions

• Q: What should I do if I have missing parts?
  • A: If you have missing parts, do not attempt to assemble the product. Please contact our customer service department at 1-800-554-6504 for assistance.
• Q: Can I adjust the length of the chain?
  • A: Yes, you can add or remove chain links to adjust the length of the chain.
• Q: What tools do I need for assembly?
  • A: The tools required for assembly are a Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses, and pliers (2).

PACKAGE CONTENTS

PART DESCRIPTION                  QTY.

A| Canopy| 1
B| Mounting Bracket| 1
C| Canopy Loop (preassembled)| 2
D| Chain| 2
E| Socket| 5
F| Fixture Loop| 2
G| Threaded Pipe| 2
---|---|---
H| Coupling| 2
I| Glass Shade| 5
J| Candle Sleeve| 5
K| Socket Base Cup| 5

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

• CAUTION – RISK OF SHOCK
  • Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.
• WARNING: This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
• Do not use bulbs with wattage greater than specified on this fixture.
• California Proposition 65

WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to http://www.P65Warnings.ca.gov

CAUTION

• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate ETL listing and/or C.S.A. certification of this fixture.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

• Estimated assembly time: 30 minutes to 1 hour
• Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses, pliers (2).

ASSEMBLY INSTRUCTIONS

1. Screw threaded pipe (G) into coupling (H).
   • NOTE: The electrical cable will need to get pulled through the individual parts as they are installed on this and later steps.
2. To open chain links:
   • Locate the split in the chain link (D). Put one pair of pliers (not included) on each side of the split and rotate the pliers in opposite directions to open the link’s split. The open link should be shaped like the letter “C”.
   • Do not twist the ends of the link sideways so that the open link cannot lay flat.
3. Connect the canopy loops (C) to the fixture loops (F) using chain (D).
   • NOTE: For best appearance be sure to weave the electrical cable through chain.
   • NOTE: Add or remove chain links once desired length is established.
   • CAUTION: To avoid damage from falling, make sure the open chain links are fully closed once assembled.
4. Orient the mounting bracket (B) so the raised center portion protrudes into the outlet box (not included). Insert long machine screws (DD) through mounting bracket (B) so the long machine screws (DD) protrude downward. Connect the mounting bracket (B) to the outlet box with short machine screws (BB).
5. Raise the canopy (A) to the outlet box (not included) and wrap the security cable around the cross bar on the mounting bracket (B) using the hook to secure the cable.
6. Wire connection guide:
   • Ground wire:
   • For installation in the United States: Wrap ground wire from outlet box around ground screw preassembled on mounting bracket (B) no less than 2 in. from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA).
   • For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around ground screw on mounting bracket (B). Tighten ground screw. Connect fixture ground wire to outlet ground wire with a wire connector (AA).
   • Supply wires:
   • Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord “D” shaped and ribbed).
   • Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth).
   • NOTE: Fixture wires will either be:
   • Black and White.
   • Parallel Cord SPT-1 lamp wire with one round smooth wire and one “D” shaped ribbed wire.
7. 7a. Pass canopy (A) over the long machine screws protruding from mounting bracket (B) and secure with lock washers (EE) and threaded knobs (CC).
   • NOTE: Make sure all wires are inside of canopy (A) and do not get pinched between canopy (A) and mounting bracket (B), or canopy (A) and ceiling.
   • 7b. NOTE: The bottom edge of an outlet box 7b should be flush with the bottom surface of a ceiling. However, many boxes are recessed into the ceiling. The long machine screws (DD) are designed to have extra length to accommodate to various box depths.
   1. The long machine screws (DD) may, at first, protrude too far past the surface of the canopy (A).
   2. Screw the threaded knobs (CC) onto the long machine screws (DD). The screws will back thread into the mounting bracket (B) until the canopy (A) is tight against the ceiling.
8. Carefully pass small opening in glass shade (I) over socket (E), and seat glass shade (I) in socket base cup (K). While holding glass shade (I) in place, carefully slip candle sleeve (J) down over socket (E) completely until it rests against the inside of glass shade (I).
   • Repeat for remaining glass shades (I).
9. Insert 60-watt max. E12 candelabra-base bulb or LED equivalent (not included) into socket (E).
   • Repeat for remaining sockets (E).

CARE AND MAINTENANCE

• Always be certain that electric current is turned off before cleaning this item.
• Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish.
• All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher.

TROUBLESHOOTING

2.  Worn or broken bulb.

| 1.  Check wiring.

2.  Replace bulb.

Contact

Distributed by

• Kichler Lighting LLC
• 30455 Solon Rd Solon, OH 44139

ATTACH YOUR RECEIPT HERE

• Serial Number: ………………….
• Purchase Date: ………………….

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-554-6504, 8 a.m. – 4:30 p.m, EST, Monday – Friday. kichler.com/customer-care/contact-us

Printed in China

References

• Contact Kichler - Get in touch with us | Kichler Lighting
• p65warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>