saro MARIE 4 Hot Table Showcase Instruction Manual

June 13, 2024
saro

Operating instructions for hot
Table showcase Model MARIE 4 / MARIE 6
Order No.: 330-1092 / Order No.: 330-1094saro MARIE 4 Hot Table
Showcase - Modell MARIE 4 (330-1092)

INTODRUCTION

Dear customer,
Thank you for purchasing the hot table showcase MARIE 4 / MARIE 6.
Please read these instructions carefully.
We wish you a lot of fun with your new hot table showcase and always good success.

TECHNICAL OVERVIEW

MODEL| MARIE 4|

MARIE 6

---|---|---
| hot table showcase| hot table showcase
Order No.| 330-1092| 330-1094
Housing material| stainless steel and safety glass| stainless steel and safety glass
Dimensions (mm)| B 773 x T 420 x H 336| B 1127 x T 420 x H 336
Weight net. (kg)| 16| 22
content (l)| 46| 68
temperature range ( C° )| + 30 / + 90| + 30 / + 90
Connection (V/Ph. /Hz./kW)| 220 – 240 / 1 / 50 / 0,5| 220 – 240 / 1 / 50 / 0,8
rated current (A)| 2,2| 3,5
protection class| IPX4| IPX4
General nominal input power(W)| 500| 800
temperature regulation| manuell| manuell
incl. GN pans| 4 x 1/3 GN, depth 40 mm| 6 x 1/3 GN, depth 40 mm
EAN-Code| 4017337 037506| 4017337 037261

SCOPE OF DELIVERY

  • 1 hot table showcase model MARIE
  • 4 x (model MARIE 4) or 6 x (model MARIE 6) GN-container
  • 1 operating manual

STANDARDS AND DIRECTIVES
The device complies with current EU standards and directives. If necessary, we will send you the corresponding declaration of conformity.
The device is designed for dry use only. No water may be filled into the device (device base)!
Illustrations in this manual may differ from the original article.

GENERAL INFORMATION

  • Remove all protective foils and clean the unit thoroughly before using it for the first time.
  • Keep these operating instructions within easy reach, near the device.
  • The manufacturer/dealer cannot be held responsible for damage caused by non-observance of these operating instructions. In addition, the safety of the device is no longer guaranteed.
  • These operating instructions must be provided when passing on the device to third parties.
  • After unpacking the device, make sure that everything is in perfect condition. If you discover any damage, do not connect the device but contact your dealer.
  • Keep the unit‘s packaging. The device can only be transported safely in its original packaging.
  • If it is not possible to store the packaging, separate the various packaging materials and return them to the nearest collection point for proper disposal.
  • Please note that all components of the packaging (plastic bags, cardboard, polystyrene parts, etc.) may endanger children and must therefore not be stored near them.
  • For hygienic reasons, at least one daily cleaning is recommended, but also after completion of a production process in the course of one day.

EXPLANATION OF SYMBOLS

WARNING!
This symbol indicates dangers that may cause injury. It is imperative that you strictly adhere to the information on occupational safety and be particularly careful in these cases.
WARNING: DANGER FROM ELECTRICAL CURRENT!
This symbol draws attention to dangerous situations caused by electrical current. Failure to observe the safety instructions may result in injury or death!
WARNING: HOT SURFACE -DANGER OF BURNS!
This symbol indicates the hot surface of the device during and after operation. Risk of burns if not observed!

SAFETY INFORMATION

  • Read these operating instructions carefully and observe the information contained therein.
  • Incorrect operation and improper handling can lead to malfunctions of the device and injuries to the user.
  • Observe the accident prevention regulations applicable to the area of application and the general safety regulations.
  • Always provide sufficient fresh air while using this unit.
  • Ensure a safe stand on a dry, non-slip surface.
  • For your safety, do not store or use gasoline or other flammable vapors or liquids near this or other equipment.
  • Do not move the unit during use.
  • Do not place the unit on a hot surface.
  • Do not let the power cable hang over sharp edges.
  • Make sure that it is not possible to pull or trip over the cable unintentionally.
  • Check the cable regularly. If it is damaged, e.g. by crushing, it must be replaced by a qualified specialist.
  • Do not leave the unit unattended during use. Be particularly careful when children are in the vicinity, as they cannot recognize the dangers of handling electrical appliances and devices that become hot, which can lead to injuries and damage to property!
  • Protect the device from moisture.
  • Do not operate the device outdoors, in the rain!
  • Do not clean the unit with an open water jet.
  • If necessary, contact a person authorized to repair the device.
  • This device may only be operated by persons who have been trained to do so.
  • No operation of the device by children or persons with limited physical, sensory or mental abilities; or lack of experience and/or knowledge, as these persons cannot recognize the dangers of using electrical appliances and/or devices which generate heat and can thus lead to accidents, fire or damage to property.
  • Always remove the plug from the socket before cleaning, or disconnect the device from the power supply; the same applies to prolonged periods of non-use.
  • To disconnect the unit from the power supply, unplug the power cord, if present, or unplug or unplug the associated fuse.
  • Use the appliance only for its intended purpose, such as keeping food warm.
  • Only use the original parts intended for the operation of the device.
  • In the event of a fault and/or malfunction, turn off the unit and unplug it from the wall outlet; or unplug the unit and contact your dealer. He will carry out the repair with original spare parts.
  • A safety distance of 50mm must be maintained on all sides around the unit during use to ensure sufficient and necessary air circulation.

CONNECTION

Before connecting the device, make sure that the voltage and frequency of the power supply correspond to the information on the nameplate of the device!
The device is delivered ready to plug in. However, if the device is used in a professional environment, it is necessary to provide equipotential bonding via a suitable cable. A corresponding connector is located on the back of the device.
Only have the device installed by a specialist!
The device must be positioned in such a way that it can be easily connected to the power supply. The mains plug should be easily accessible at all times! Ensure that there is always enough free space to operate and maintain the device at all times.
The spacers on the rear side of the unit ensure sufficient distance to the wall.
The unit should be checked and serviced regularly by a qualified person!
Attention! When the unit is switched on for the first time, there may be low smoke emission, with the heating elements. This is normal and does not constitute a malfunction!
WARNING: DANGER OF FIRE!

  • Do not place the device near flammable materials or liquids! A sufficient distance must be maintained to all sides!

WARNING: DANGER FROM ELECTRICAL CURRENT!

  • Make sure that the power cord is free of damage.
  • A damaged device must not be used! In this case please contact your dealer!
  • Before connecting the device to the mains, check whether the type of current and the mains voltage correspond to the information on the type plate of the device.
  • If necessary, have the connection taken over by a specialist.
  • Do not use adapters or extension cables.

INSTALLATION AND OPERATION

instalation

  • Place the unit on a level and safe surface that supports the weight of the unit and is not heat-sensitive.
  • Never place the unit on an inflammable surface (e.g. tablecloth, carpet, etc.).
  • Do not position the unit near open fireplaces, electric furnaces / arc furnaces / electric heaters or other heat sources.
  • Position the device so that the plug is easily accessible.

operation

  • Before first use, clean the inside and outside with a soft cloth and a mild detergent.

  • Thoroughly rinse the GN containers once.

  • Then dry the device thoroughly.

  • Connect the device to a grounded power outlet.

  • Set the temperature as desired for the respective food.
    You can adjust the desired temperature in the range between 30 °C – 90 °C.

  • The temperature inside the display case can be read from the front display.

  • Some of the equipment parts can become very hot. Always use protective gloves when placing or removing food.

  • The food is kept warm at the temperature you set.

  • To place or remove food, use the door.

  • If necessary, switch on the interior light with the light switch of the device.

  • Unplug the unit when not in use.

STRUCTURE AND PARTS

saro MARIE 4 Hot Table Showcase - glas door

WARNING: HOT SURFACE! DANGER OF BURNS!

  • Some components of the table showcase become very hot during operation! There is a risk of burns when touching these components.
  • When adjusting or removing, always wear suitable heat protection gloves!

WARNING: DANGER DUE TO ELECTRIC CURRENT!

  • Do not touch the device, cables and plugs with wet or damp hands.
  • Do not immerse the unit in water or other liquids. If the device should fall into the water, immediately unplug it from the mains and have it checked by a specialist before reusing it. There is a danger of fatal electric shock.

MAINTENANCE

Maintenance of the hot showcase MARIA may only be carried out by authorized persons!
Before starting any repair or cleaning work, make sure that the unit is disconnected from the power outlet and cooled down.
Do not use any acidulants and make sure that no water penetrates into the unit.
To protect yourself from electric shock, never immerse the device, its cables and plug in water or other liquids.
Do not use a pressurized water jet to clean the unit.
Check the power cord from time to time to make sure it is not damaged in any way. Never use the device if cables are damaged. If cables are damaged, they must be replaced by a qualified electrician. Only a qualified technician should carry out repairs and maintenance on the device. Do not attempt to repair the unit yourself.
WARNING: DANGER DUE TO ELECTRIC CURRENT!

  • A damaged device must not be used! In this case, disconnect the device from the power supply and contact your dealer!
  • Never attempt to open or repair the unit yourself. There is a danger to life!

CLEANING

Always disconnect the unit from the power supply before cleaning!
The unit should be cleaned regularly.
Clean the inside and outside of the unit with a soft, damp cloth and a mild detergent.
Clean the placement grids and the case with a soft, damp cloth and a mild detergent.
Clean the GN containers (Dishwasher safe ) regularly.
Use only a soft cloth and make sure you never use any abrasive or pad that could scratch the surface.
After cleaning, use a soft, dry cloth to wipe and polish the surface.
Make sure the unit has been properly cleaned before storing it in a dry place.
WARNING: HOT SURFACE! DANGER OF BURNS!

  • Do not start cleaning before the unit has cooled down sufficiently!

EXPLODED DRAWING

Order No: 330-1092)

saro MARIE 4 Hot Table Showcase - EXPLODED DRAWING

1 door glas 20 front pulley
2 handle 21 big gasket for nut
3 a-type sealing strip 22 decorating gasket for nut
4 screw 23 decorating parts for nut
5 upper plate 24 left glass
6 front glass 25 left plate
7 sealing strip 26 baseboard
8 / 1/3 GN-pans 27 rubber feet
9 stainless steel pans 28 double-faced protective ring ø 6
10 heating element holder #1 29 double-faced protective ring ø 12
11 heating element holder #2 30 power line
12 heating element holder 31 cable clip
13 base shield 32 switch
14 vibration absorbing gasket 33 hermostat
15 thermostat 34 indicator light
16 thermostat 35 right plate
17 back shield 36 right glass
18 probe pressing plate 37 plug-type fixer 17
19 head shield

MARIE 6 (Art-Nr.:/Order No: 330-1094)

saro MARIE 4 Hot Table Showcase - EXPLODED DRAWING1

PARTS NAME

MARIE 6 (Art-Nr.:/Order No: 330-1094)

1 door glas 20 front pulley
2 handle 21 big gasket for nut
3 a-type sealing strip 22 decorating gasket for nut
4 screw 23 decorating parts for nut
5 upper plate 24 left glass
6 front glass 25 left plate
7 sealing strip 26 baseboard
8 / 1/3 GN-pans 27 rubber feet
9 stainless steel pans 28 double-faced protective ring ø 6
10 heating element holder #1 29 double-faced protective ring ø 12
11 heating element holder #2 30 power line
12 heating element holder 31 cable clip
13 base shield 32 switch
14 vibration absorbing gasket 33 thermostat
15 thermostat 34 indicator light
16 thermostat 35 right plate
17 back shield 36 right glass
18 probe pressing plate 37 plug-type fixer 17
19 head shield

CIRCUIT DIAGRAM

MARIE 4 (Art.-Nr./Order No: 330-1092)

saro MARIE 4 Hot Table Showcase - CIRCUIT DIAGRAM

PACKAGING DISPOSAL

**** Please separate the packaging materials accordingly and return them to the responsible collection points for recycling and environmental housing.

DISPOSAL

Once the appliance has been used up, please dispose of it properly at a collection point for electrical appliances.
Electrical appliances do not belong in household waste.
Your responsible administration will inform you about the addresses and opening hours of collection points.
**** This is the only way to ensure that old appliances are properly disposed of and recycled. Thank you very much!

Made in P.R.C for:
SARO Gastro-Products GmbH
Sandbahn 6, 46446 Emmerich am Rhein, Germany
Tel. +49(0)2822 9258-0
Fax +49(0)2822 18192
E-Mailinfo@saro.de
Web:www.saro.de
Stand 06/2018 TM

Documents / Resources

| saro MARIE 4 Hot Table Showcase [pdf] Instruction Manual
330-1092, 330-1094, MARIE 4 Hot Table Showcase, Hot Table Showcase, Table Showcase, Showcase
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals