BUXTON BTW 6600 Wireless Stereo Earphones User Manual
- June 4, 2024
- BUXTON
Table of Contents
BUXTON BTW 6600 Wireless Stereo Earphones
Safety Instructions
This product has been designed with the utmost safety in mind. However, incorrect use may lead to electric shock or fire. This is why users should observe the following instructions when using this device. This device uses a semiconductor unit and contains no user serviceable parts. Do not disassemble this device, otherwise you are exposed to the risk of electric shock. If the unit is damaged, please have it repaired by a qualified service technician.
Power source
The power supply of this device must comply with the parameters indicated on
the type plate.
Heat source
Keep this unit out of heat sources like stove or direct sunlight.
Cleaning
Prior to cleaning, please disconnect power first. For cleaning, don’t use
liquid detergents or caustic liquids – just clean the unit with a soft cloth.
Heavy objects
Do not place heavy objects on this unit, otherwise the unit may be damaged.
Faults to be repaired
If any of the following problems occurs, please disconnect power to the unit
and contact a qualified service technician.
- The power cord or plug has been damaged.
- Fluids or other foreign objects have entered the unit.
- If the unit does not work, even though you operate it according to the instructions, do not press any buttons other than those listed. Otherwise, damage to this unit may occur along with a more demanding repair.
- The unit fell from a high place to the ground.
- There is a smell of burning from inside the unit.
Maintenance
If you don’t have enough technical knowledge necessary to maintain this unit, don’t attempt to repair it by yourself. By removing the cover, you are exposed to a risk of electric shock. If needed, please contact a qualified service technician.
Replacement of parts
If you need to replace any part of this unit, ask your service technician to
make a replacement for equal spare part models. Replacement with other models
of spare parts may cause serious malfunction, electric shock or shorten the
life of the device.
Safety check
When done with the maintenance, ask your service technician to perform an on-
site safety check to make sure that the unit’s operation is safe.
Note:
Before using this product, read these instructions carefully and keep it well
for future use.
WARNING
Extremely loud music can mask traffic sounds or other danger signals. Make
sure you never lose track of what’s happening in your area.
Supply content
- A) 1X “L” and “R” earphone
- B) 1X Charging case
- C) 1X User’s manual
- D) 1X USB-C charging cable A
Description of the BT earphones
Putting into operation
Before first use, be sure to read the safety instructions contained in this user’s manual carefully. Before using for the first time, remove the protective film of the charging contacts on the bottom of the earphones and return them to the charging case. Start charging the charging case and the earphones to the maximum level.
Turning on the earphones – Taking the earphones out of the case will automatically switch them on. When the earphones are in the off state outside the charging case. Press and hold the touch pad on each earphone and wait for the earphones to announce the “BUXTON” greeting.
Turning off the earphones – Inserting
the earphones into the charging case will automatically turn off the
earphones. Long press and hold the touch pad until the message “SEE YOU” is
heard in unpaired mode. Pairing the earphones with each other – The earphones
are already paired from the factory and do not need to be paired with each
other. (If pairing to TWS mode fails, return the earphones to the charging
case and repeat the above instructions).
Caution : To prevent damage to your hearing, always keep the volume level of your device to a minimum before connecting BT earphones to your mobile device. Keep the touch control pad clean and avoid touching other objects or body parts such as hair.
Note : If the BT earphones are not paired with any device, they will turn off when left idle for a long time. Put them in the case.
Pairing your earphones via Bluetooth
To pair the BT earphones with your mobile device, do the following: Remove the
earphones from the charging case and search for the Bluetooth earphones name
“BTW 6600” on the device you want to pair and start the pairing process. If
you are prompted for a pairing code while pairing your device and BT headset,
use the code: “0000”. To cancel the pairing process, disconnect the BT
earphones from your mobile device (cancel the Bluetooth pairing).
Note: To ensure a stable Bluetooth connection, keep a distance of up to 10 metres between the BT earphones and the paired device. Depending on ambient interference, in some cases it may be necessary to maintain a shorter distance between the BT headset and the paired device.
Charging
A charged battery provides power for several hours of operation at normal
volume levels. A high volume consumes more battery power; therefore, we
recommend listening at normal volume levels.
When the BT earphones are placed in the charging case, the LED indicators of
the case show the statuses:
Charging case indicator:
The intermittent yellow, white, light blue indication according to the colour
of the BT earphones indicates the charging of the earphones. When the USB-C
charging cable is connected, a slow intermittent red indication shows the
charging of the charging case. Discharged charging case is indicated by a fast
intermittent red indication – connect the charging cable.
Earphones LED indicator:
Charging of the earphones is indicated by a white LED on each of them. When
the LED goes off the earphones are fully charged and ready to use. The pairing
of the earphones is indicated by a fast intermittent white LED indication.
Attention : For charging, use only the original accessories supplied with
the appliance. To achieve maximum battery life, it is advisable to start
charging the battery only when
the battery is low (10% – 20%). Charge continuously until fully charged. If
the battery life is already very short, it is exhausted and we recommend you
contact an authorised service centre for more information.
Recommendation : If your earphones are not to be used for an extended period of time, we recommend to fully charge the batteries once every two to three months. We recommend storing the BT earphones together with the charging case with a charged battery to avoid irreversible damage to the batteries (loss of capacity).
Technical specifications
- Bluetooth : V5.0 BLE
- BT connection range : 10 m
- BT profiles: A2DP 1.3, AVRCP 1.6, AVDTP 1.3, HFP 1.7, GAVDP 1.3
- Bluetooth frequency response range : 2.4 GHz – 2.4835 GHz
- Maximum transmitter power : 100 mW Chipset: Actions ATS3015
- Codec : AAC, SBC
- Diameter of inverters : 10 mm
- One microphone per earphone – handsfree ready
- Earphones charging indicator Playback time per charge: up to 5 h (80% volume) Total playback time: up to 20 hours (80% volume)
- Call time : up to 4 h
- Standby time : up to 300 h
- Earphones charging time : 1.5 h
- Case charging time : 1.5 h
- Battery capacity of one earphone : 40 mAh / 3.7 V
- Charging case battery capacity : 400 mAh / 3.7 V
- Charging port : USB-C (DC 5 V / 300 mA)
- Frequency range : 20 Hz – 22,000 Hz
- Sensitivity: 105 dB +/- 3 dB @ 1 kHz
- Impedance : 32 Ω ± 15%
- Weight of one earphone : 3.9 g
- Charging case weight: 35.5 g
- Charging case dimensions : 60 × 49.9 × 26.5 mm (W × H × D)
- Package contents : TWS earphones, charging case, USB-C charging cable, user’s manual
Please read these instructions carefully before use.
Safety warning
Do not place sources of open flame, such as lit candles, on the device Dispose
of batteries in an environmentally friendly manner, taking into account the
environmental impact of battery disposal Do not expose batteries (installed
batteries) to excessive heat, such as fire
Warning : To avoid possible hearing damage, do not listen to high volume sound for long periods of time. For safety reasons, be aware of your surroundings when using the earphones. Not suitable for children
DISPOSAL OF DISCARDED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol placed on the product, accessories or package notifies that the
product must not be treated as household waste. Please dispose of this
product in a collection centre designed for recycling electric and electronic
equipment. In some EU or European countries, you can return your products to
your local dealer when buying a new equivalent product. Correct disposal of
this product helps save valuable natural resources and prevents possible
adverse impacts on the environment and human health that might be caused by
improper waste disposal. For further information, please contact your local
authorities or the nearest waste disposal collection centre. Improper
disposal of this type of waste may lead to penalties under the law.
For EU companies
If you need to dispose of an electric or electronic device, ask your dealer
your supplier for necessary information.
Disposal in countries outside the European Union
If you wish to dispose of this product, please ask your local authorities or
your dealer for the information necessary for the correct disposal method.
This product complies with all relevant EU basic regulatory requirements.
Changes in the text, design and technical specifications may be made without prior notice and we reserve the right to make such changes. FAST ČR, a. s. hereby declares that the radio equipment type BTW 6600 complies with Directive 2014/53/EU. The complete version of the EU Declaration of Conformity can be found at:www.buxton.cz
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>