BUXTON BHP 8700 Wireless Stereo Headphones User Manual

: June 15, 2024
: BUXTON

Table of Contents

Included Contents
Putting into Operation
Bluetooth
Factory Settings
Charging
Technical Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WIRELESS STEREO HEADPHONES
User’s manual
BHP 8700

Included Contents

1× Headphones
1× User’s manual
1× USB-C charging cable

BUXTON BHP 8700 Wireless Stereo Headphones - Included
Contents

1	USB-C charging connector
2	Volume down button (press lx )

Previous track (long press)
3| On/Off button (long press)
Play/pause (press l x)
Answer / end call (press lx) / reject call (long press)
SRI / Google Assistant (press 2x)
Low latency on/off (press 3x)
4| Volume up button (press 1 x)
Next track (long press)
5| LED battery charge indicator — low battery — intermittent indication – charging — continuous indication – charged battery — no indication
BT status LED indicator – alternating red and blue — ready to pair – blue slowly intermittent — connected to the device
6| Microphone
7| Change EQ mode (BASS, signature —normal mode)
8| EQ BASS mode LED indicator
L| Left earpiece — left audio channel
R| Right earpiece — right audio channel

Putting into Operation

Before first use, be sure to read the safety instructions contained in this user’s manual carefully.
Before first use, charge the headphones to the maximum level.
Turning on the headphones – press and hold the “on/off” button and wait for the headphones to announce the “BUXTON” greeting.
Turning off the headphones – press and hold the “on/off” button and wait for the headphones to announce “SEE YOU”.
Warning: To prevent damage to your hearing, always keep the volume level of your device to a minimum before connecting BT headphones to your mobile device.
Note: The BT headphones will turn off after a longer period of inactivity unless they are paired to another device.

Bluetooth

The headphones are equipped with a twochannel BT module. This means that it is possible to have headphones connected to two devices at the same time. The audio signal will come from the last connected device until there is a state change in the other device (for example, an incoming call). The audio signal source used will then be replaced by a second audio signal source. You cannot operate both audio signals simultaneously.

Note: pair the headset with one device first, then disconnect the device after successful pairing. Pair the headset with the second device and then connect the first device.

To pair the BT earphones with mobile device, do the following:
Turn on the BT headphone and search for its Bluetooth name “BHP 8700” on the device to which you wish to pair and start the pairing process. If you are asked to enter a pairing code when pairing your device and BT headphone, use the code: “0000”.
To cancel pairing, disconnect the BT headphones (cancel Bluetooth pairing) on your mobile device.

Note: To ensure a stable Bluetooth connection, make sure that the distance between the BT headphones and your paired device is kept within 10 meters. Depending on ambient interference, in some cases it may be necessary to maintain a shorter distance between the BT earphones and the paired device.

Factory Settings

If the headset needs to be reset to factory settings, press the volume up “+” and volume down “-” buttons simultaneously when the headset is switched on. Wait approximately 10 seconds and release the buttons. The LED will flash red 3 times and the headset will turn off with the “SEE YOU” message. Turn on the headphones.

Charging

A charged battery provides power for several hours of operation at normal volume levels. A high volume consumes more battery power; therefore, we recommend listening at normal volume levels. Low battery will be reported at 20% and 10%, at the same time the LED indicator will give red intermittent warning. The charging process will be indicated by a red solid LED until the charging adapter is disconnected or fully charged.
Warning: For charging, use only the original accessories supplied with the appliance. To achieve the maximum battery lifetime, it is best to start charging the battery after the low battery power notification. Charge continuously until fully charged. If the battery life is already very short, it is exhausted and we recommend you contact an authorised service centre for more information.
Recommendation: If your headphones are not to be used for an extended period of time, we recommend to fully charge the batteries once every two to three months.

Technical Specifications

Bluetooth: V5.3 BLE
Bluetooth Frequency Response Range: 2.4 GHz – 2.4835 GHz
Maximum transmitter power: 100mW
Operating Range: up to 50 m
BT Profiles: A2DP 1.3, AVRCP 1.6, HFP 1.8, SPP 1.2
Chipset: JL AC7003
Codec: AAC, SBC
Drivers Diameter: 40 mm
Control: 4 Multifunction Buttons
Built-in Microphone
Playback Time: up to 60 h (50% Volume)
Playback Time: up to 54 h (100% Volume)
Talk Time: up to 22 hrs.
Standby Time: up to 300 hrs.
Charging Time: ≤ 2 h
Rechargeable Battery: 400 mAh / 3.7 V Li-Pol
Charging Port: USB-C (DC 5 V / 500 mA)
Headset Charging Indicator
Frequency Response: 20 Hz – 20 000 Hz
Sensitivity: 96 dB +/- 3 dB (@ 1 kHz)
Impedance: 32 Ω +/- 15 %
Weight: 224 g
Dimensions: 160 × 197 × 81 mm (w / h / d)
Package Contents: Headphones, USB-C
Charging Cable, User Manual

DISPOSAL OF DISCARDED ELECTRICAL AND ELECTRONIC EQUIPMENT

**** This symbol on the product, accessory or packaging indicates that the product must not be treated as normal household waste. Please dispose of this product in a collection yard designated for the recycling of electrical and electronic equipment. In some EU countries or in some European countries, you can return your products to your local retailer when you buy an equivalent new product. Correct disposal of this product helps save valuable natural resources and prevents possible adverse impacts on the environment and human health that might be caused by improper waste disposal. For further information, please contact your local authorities or the nearest waste disposal collection centre. Improper disposal of this type of waste may lead to penalties under the law.

For companies in the European Union
If you need to dispose of electrical or electronic equipment, ask your dealer or supplier for the necessary information.

Disposal in countries outside the European Union
If you wish to dispose of this product, please ask your local authorities or your dealer for the information necessary for the correct disposal method.

**** This product complies with all relevant EU basic regulatory requirements.

Changes in the text, design and technical specifications may be made without prior notice and we reserve the right to make such changes.
FAST ČR, a. s. hereby declares that the radio equipment type BHP 8700 complies with Directive 2014/53/EU.
The complete version of the EU Declaration of Conformity can be found at: www.buxton.cz.
Manufacturer: FAST ČR, a.s., U Sanitasu 1621, Říčany 251 01, Czech Republic
Authorized service centers: Visit www.sencor.com for detailed information about authorized service centers.