CREALITY CR-Laser Falcon Engraver Laser Engraving Machine User Manual
- June 15, 2024
- Creality
Table of Contents
CR-Laser Falcon Engraver Laser Engraving Machine
User Manual
CR-Laser Falcon Engraver Laser Engraving Machine
Dear customer,
Thank you for purchasing our product. Please read the following instructions
carefully before first use and keep this user manual for future reference. Pay
particular attention to the safety instructions. If you have any questions or
comments about the device, please contact the customer line.
Rendering picture
Dear
Consumers:
Thank you for choosing our products. For the best experience, please read the
instructions before operating the machine. Our teams always be ready to render
you the best services. Please contact us via the phone number or e-mail
address provided at the end when your encounter any problem. For a better
experience in using our product, you can also learn how to use the engraving
machine in the following ways:
- View the accompanied instructions and videos in the TF card.
- Visit our official website www.creality.com to find relevant software/hardware information, contact details, operation and maintenance instructions.
Firmware Upgrade
Download the latest firmware from https://www.creality.com/pages/download
/-cr-laserengraver, save the “.bin” in the root directory of the TF card, and
delete other files in TF card. Insert the TF card into the machine when
powered off, and it will update automatically when powered on. The buzzer will
sound in the update process. When the update is completed, the sound will stop
(do not power off in the update process).
Security Statement
For the purpose of engraving or cutting with a laser engraving machine, allow the workpiece to be exposed to the high-density laser beam emitted by the laser engraving machine. The workpiece may be subject to gasification without combustion as it is pretty hot on the surface. On the other hand, most workpieces are essentially combustible, which may be ignited, leading to an open flame and consequently to the machine breakdown and environmental contamination.
- It is prohibited to store the machine in areas close to combustible and explosive substances, volatile solvents or source or heat. Instead, store it in a well ventilated, cool and dust-free place.
- Make sure that only the specific attached power cord rather than other similar power cords are used during installation.
- Clean the tripod and laser module with a dry cloth regularly when the power is off.
- Ensure to run the laser at 0°C-35°C. It is prohibited to run the machine under wet environment or in thunderstorm weather.
- Switch off the machine if it is offline for an extended period of time, and unplug the power cord.
- It is prohibited to come in contact with electronic areas with hands or other tools when the machine is connected to power supply.
- Touching any moving parts and laser module while the machine is running is prohibited.
- Before engraving, place a flat object that cannot be penetrated by the laser, such as an aluminium alloy or stainless-steel plate on the workbench, and then place processing material.
- Wear goggles to prevent vision damage arising from exposure to the laser spot during laser engraving operation.
- It is advisable to run the machine under well ventilated condition as laser engraving may generate small amount of fume or gas.
- Children under 10 years old are not allowed to run the machine without adult presence, which otherwise may lead to personal injury.
- Put in place fire extinguishers in case of use, which shall be regularly checked. It is prohibited to keep the machine unattended while it is running.
- Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, play attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purpose. Realty will not be responsible for any violators’ legal liability under any circumstance.
Parameters
| Model | CR-Laser Falcon |
|---|---|
| Machine size | 568632198mm |
| Net weight | 3.2kg |
| Operation system | Windows/MacOS |
| Input | 100-240V ~ 50-60Hz |
| Output | DC 24.0V 3.0A |
| Range of operating temperature | 0°C-35°C |
| Safety certification | IEC60825, FDA, CE, ROHS, FCC, UKCA, UL, PSE |
| Engraving size | 400mm*415mm |
| Laser source | Semiconductor laser unit |
| Laser wave length | 455±5nm |
| Laser power | 5W/10W |
| Safety class | Class IV (FDA/FDA classification standard) |
| Laser engraving software | LaserGRBL, LightBurn |
| Format files | jpeg, jpg, png, bmp, svg, dxf |
| Type of supporting materials | Cardboard, wood, bamboo, rubber, leather, |
fabric, acrylic, plastic, etc
Equipment Intro
Parts
List 
Assemble directions
Assemble the left Y-axis assembly: Pass the left Y-axis assembly (with the
belt up) through the X-axis assembly and put on the belt in the direction
shown in the figure: Assemble the right Y-axis and it is the same as above.
Insert two T-shaped nuts into the left and right Y-axis assembly. 
Assemble rear X-axis
profile and front X-axis profile: Lock with eight M5*20 screws. 
Assemble three tripods and control box assembly: Lock with eight screws. Push the X-axis assembly to the end and make sure it is parallel to the rear X-axis profile.
Tighten the belt and lock the belt with hexagon screws. 
Assemble 5W laser module: Assemble it into the
fixing plate and the fixed focus bar should contact with the surface of the
processed material when it is naturally vertical downward. Then lock it with
two hand screws on the right and turn the fixed focus bar clockwise until it
is attracted by the magnet. Finally plug in the laser module cord. Assemble
10W laser module: Please place the multi-level fixed focus bar between the
laser module and the processed material. Follow the tips and make the bottom
of the laser module contact with the corresponding surface of the multi-level
fixed focus bar. Finally lock with two hand screws on the right. For example,
if you engrave or cut a 2mm basswood or other material:
For better engraving effect, try to elevate the laser
module as far away from the workbench as possible on the premise that the
focal length is correct. The laser module must be installed and removed only
when the power is off.
Software installation and usage guide
The machine supports real-time working by Type-C (Light Burn or LaserGRBL) and
offline working (Light Burn only).
Start Engraving
Please follow the assembly directions to focus correctly and wipe the
protective lens of the laser module with dustless cloth and alcohol to ensure
the best engraving effect. The filter cotton in 5W lase module and the cover
for 10W laser module can be removed directly for cleaning. Offline working
First generate and engraving file (.geode/.gc/.g/.nc/.ngc) through
LightBurn, and save it to the root directory of the TF card (The machine reads
the engraving file whose modified date is latest in the root directory of the
TF card by default. It is recommended to delete other engraving files in the
root directory) Insert the TF card before powering on, connect the machine
with the supplied power adapter and power cord. Finally turn on the red switch
on the left side of the control box.
When power on, the machine emits “beep, beep, beep”.
After the machine is initialized, it enters the standby mode, and the
indicator light turns into breathing state.
Press the microswitch, it enters preview mode from standby mode, the laser
head will emit weak light, and repeat movement around the largest X, Y, edges
of the processed picture with indicator light on. At this time, adjust the
material to a suitable position. In preview mode, press microswitch again, it
enters engraving mode. At this time, the laser head will emit strong light,
the machine will start engraving with indicator light on.
Pause engraving: press the microswitch (or click “Pause” button in the
software). At this time, the indicator turns into breathing light. Press the
microswitch again to continue engraving.
Cancel engraving: Please press and hold the microswitch for 3 seconds (or
click “Cancel” button in the software), it will “beep” once, starts to reset,
and “beep” twice after reset is complicated. Enter standby mode, the indicator
light turns into breathing light. After engraving is completed, it will “beep”
three times and reset. After reset completed, it “beep” twice, enters standby
mode, and the indicator light turns into breathing light.
Real-time working
For real-time working by Type-C, please refer to the tutorial in the TF card.
During online working, do not insert the TF card and do not press the
microswitch on the control box.
Indicator status
- Light off: The machine is in power-off state, or the power is abnormal.
- Breathing light: The machine is in standby mode, you can press the microswitch to enter preview mode or engraving mode. (Present a light effect with a gradual change or light shade).
- Light flashes: the machine is in upgrade mode or abnormal, and the buzzer beeps rapidly, and it will automatically enter standby mode after the upgrades is completed or the abnormality is cleared.
- Light always on: the machine is in preview mode or engraving mode. The laser head is working, please pay attention to safety.
Exception Handling
If the machine turns on it side or moves suddenly during working, it will
turn off the laser. Motor stops moving, indicator light flashing, and buzzer
emits alarm.
Solution: Please move the machine to its original position and press
microswitch on the machine control box to continue previewing or engraving
after clearing abnormality (The microswitch only works during offline
working).
Offline working
Real-time working 
Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase. The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:
- Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
- Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
- Natural wear and aging of consumables or components during use (such as batteries, etc.).
- Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
- If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.
www.alza.co.uk/kontakt
✆ +44 (0)203 514 4411
Importer
Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7,
www.alza.cz
References
- Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
- Alza.sk – rýchly a pohodlný nákup odkiaľkoľvek | alza.sk
- alza.at
- Alza | Alza.co.uk
- Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
- Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
- Alza.cz
- alza.de
- alza.hu
- alza.sk
- Creality - Global Leader in Consumer-Level 3D Printer Ecosystems and Creator
- 3D Printer Slicer Software& Firmware Download - Creality 3D
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>