CREALITY SM-001 Plus Resin 3D Printer User Manual

CREALITY SM-001 Plus Resin 3D Printer User Manual

Dear Consumers,
Thank you for choosing our products.For the best experience,please read the instructions before operating the Printer. Our teams are always ready to render you the best services. Please contact us via the phone number or e-mail address provided at the end when you encounter any problem with the Printer.

For a better experience in using our product, you can also access how to use the printer in the following ways:
View the accompanied instructions and videos in the U disk.

Visit our official website www.creality.com to find relevant software/hardware information,contact details and operation and maintenance instructions.

Firmware/Software Downloads and Upgrades
The product has access to both LycheeSlicer and CHITUBOX. WIFIprinting and access to the Creative Cloud are under development.

Slicing software supported：

Download the firmware and HALOT BOX slicing software at: https://www.creality.com
Download the CHITUBOX slicing software at: https://www.chitubox.com
Download the LycheeSlicer slicing software at: https://lychee.mango3d.io

• Do not use the printer any way other than described to avoid personal injury or property damage.
• Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.
• Please use recommended resin in case damage to machine.
• Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.
• Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.
• Please do not open the plastic cover during usage, otherwise the printing will be interrupted.
• Do not wear cotton gloves when operating the printer. Such cloths may become tangled in the printers moving parts leading to burns, possible bodily injury, or printer damage.
• Please wait after the print is finished. please wear gloves to take out the print tools.
• Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other material off the frame, guide rails, or wheels.
• Use glass cleaner or isopropyl alcohol to clean the print surface.
• Children under 10 years should not use the printer without supervision.
• Tips Do not plug or unplug the power cord when power on.
• Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Creality will not be responsible for any violators’ legal liability under any.

1. Equipment Introduction

1. Hexalobular socket screw
2. Buliding platform
3. Resin vat
4. Touch screen
5. Leveling screw
6. USB port
7. Air filter
8. Hexalobular socket screw
9. Power socket
10. Power switch

2. Equipment parameters

3. Parts List

4. Interface Information

5. Leveling Platform

6. Load Resin

Pour the UV photosensitive resin into the resin vat. The slot capacity is 500ml/1000ml。

Tips: How to change resin?
Take out the resin vat slowly, pour out the remaining resin into the container, clean the resin vat, pour in new resin,and then install the resin vat to the machine.

Caution:

1. Resin may cause skin irritation or an allergic skin reaction. Please wear gloves before use to avoid direct contact with the skin.
2. Do not exceed the maximum capacity scale of the tray when pouring in filaments to prevent them from overflowing during the printing process.

7. Release Film (FEP) Replacement

Tips:

1. The diagram is a reference for the film change procedure, please refer to the physical product; if there are excess edges after installation of the release film, you will need to cut them off.
2. It is recommended to replace the release film when it has been used for more than 200 hours.

8. Preparation of U-shaped disc-shaped printing sheets

Note: The published UI of slicing software shall prevail for the interfaces of HALOT BOX, Lychee Slicer and CHITUBOX.

9. USB Disk Printing

10. Clean the Resin Vat

Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official website of the latest firmware Ul as the standard.

11. Wiring Connection

Mainboard circuit wiring diagram

Pinboard circuit wiring diagram

12. Troubleshooting

Due to the differences between different machine models, the actual objects and the images can differ. Please refer to the actual machine. The final explanation rights shall be reserved by Shenzhen Creality 3D Technology Co., Ltd.

SHENZHEN CREALITY 3D TECHNO LOGY CO.,LTD.
1 8th Floor, JinXiuHongDu Building, Meilong Road, Xinniu Community,
Minzhi Street, Longhua District, Shenzhen City, China.
Official Website: www.creality.com
Tel: +86 755-8523 4565
E—mail: cs@creality.com

Read More About This Manual & Download PDF:

References

• Creality - Global Leader in Consumer-Level 3D Printer Ecosystems and Creator
• Download the latest version of Lychee Slicer for SLA/Resin 3D Printers
• CHITUBOX SLA/DLP/LCD 3D Slicer Software
• Creality - Global Leader in Consumer-Level 3D Printer Ecosystems and Creator

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>