CREALITY CL-79-SM-001 3D Printer User Manual

: June 2, 2024
: Creality

Table of Contents

CREALITY CL-79-SM-001 3D Printer
Specifications
Product Usage Instructions
FAQ
Equipment Introduction
Equipment parameters
Parts Content List
Assemble the 3D Printer
USB Disk Printing
Creality Cloud Online
Creality Cloud App Print
Wiring Connection
Troubleshooting
FCC Statement
contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CREALITY CL-79-SM-001 3D Printer

Specifications

Model Name	HALOT-ONE PLUS
Build Size	172102160mm (lengthwidth height)
XY Axis Resolution	4320*2560
XY Axis Accuracy	0.04mm
Print Speed	1-4S/ layer
Layer Thickness	0.01-0.2mm
Touch Screen	5-inch touch screen

Product Usage Instructions

Equipment Introduction

The equipment includes a hexalobular socket screw, levelling screw, platform plate, resin vat fixing screw, resin vat, touch screen, limit sensor, air filter, USB port, power switch, and power receptacle.

Equipment Parameters

The HALOT-ONE PLUS has specific parameters including the model name, build size, XY axis resolution, XY axis accuracy, print speed, layer thickness, touch screen size, light source type, rated voltage, rated power, machine size, package size, net weight, gross weight, print method, machine language, slicing software, and operation system compatibility.

Parts Content List

The parts list includes a print platform, U disk, resin vat, screwdrivers set, metal blade, release film, tray fixing screws, 3D printer unit, power cable, plastic blade, paper funnel, and calibration card.

Assemble the 3D Printer

To assemble the printer, align the resin vat with the tray fixing screws and tighten them. Place the plastic upper cover on the machine body to complete the installation.

Interface Information

Check whether the light source is normal and use the UI interface as a reference for operation.

Levelling Platform

Raise the platform and loosen the rubber screws on the sides of the resin vat to remove it.
Loosen the screws on the connecting plate of the platform and attach the calibration card on the printing screen.
Press Settings > Print Settings > Z-axis movement > Leveling to ensure the platform fits evenly with the paper.
After confirming evenness, lock the screws of the platform.

FAQ

Q: Are there any age restrictions for using the printer?
A: Children under 10 years should not use the printer without supervision to ensure safety.
Q: How can I clean the print surface?
A: Use glass cleaner or isopropyl alcohol to clean the print surface effectively.
Q: How can I upgrade the firmware of the printer?
A: Please visit the official website at https://www.creality.com/download, select the relevant printer model, switch the language if needed, and download the required firmware for installation.

Dear Consumers,

Thank you for choosing our products.For the best experience, please read the instructions before operating the Printer. Our teams are always ready to render you the best services. Please contact us via the phone number or e-mail address provided at the end when you encounter any problem with the Printer. For a better experience in using our product, you can also access how to use the printer in the following ways: View the accompanied instructions and videos in the U disk. Visit our oﬃcial website www.creality.com to ﬁnd relevant software/hardware information, contact details and operation and maintenance instructions.

Firmware Upgrade

Please login to the oﬃcial website https://www.creality.com/download, switch the language select the relevant printer and model and download the required ﬁrmware ou can use it after the installation.

NOTES

Do not use the printer in any way other than described to avoid personal injury or property damage.
Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.
Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.
Please use the recommended resin in case damage to the machine.
Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.
Please do not open the plastic cover during usage, otherwise the printing will be interrupted.
Do not wear cotton gloves when operating the printer. Such cloths may become tangled in the printer’s moving parts leading to burns, possible bodily injury, or printer damage.
Please wait after the print is finished. please wear gloves to take out the print tools.
Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other material off the frame, guide rails, or wheels. Use glass cleaner or isopropyl alcohol to clean the print surface.
Children under 10 years should not use the printer without supervision.
Tips Do not plug or unplug the power cord when powered on.
Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Creality will not be responsible for any violators’ legal liability under any.

Equipment Introduction

CREALITY-CL-79-SM-001-3D-Printer-fig-1

Hexalobular socket screw
Leveling screw
Platform plate
Resin vat ﬁxing screw
Resin vat
Touch screen
Limit sensor
Air filter
USB port
Power switch
Power receptacle

Equipment parameters

Basic Parameters

Parts Content List

CREALITY-CL-79-SM-001-3D-Printer-fig-2

CREALITY-CL-79-SM-001-3D-Printer-fig-3

Assemble the 3D Printer

Take out the resin vovt align the two tray ﬁxing screws with the corresponding holes and tighten them to ﬁx. (as the picture shows)
CREALITY-CL-79-SM-001-3D-Printer-fig-4

CREALITY-CL-79-SM-001-3D-Printer-fig-5

Interface Information

CREALITY-CL-79-SM-001-3D-Printer-fig-6

Note: Check whether the light source is normal The UI interface only for reference, the actual UI.

Levelling Platform

CREALITY-CL-79-SM-001-3D-Printer-fig-7

Raise the platform, loosen the rubber screws on the left and right sides of the resin vat, and take out the resin vat.
Loose the four screws on the connecting plate on molding platform plate, attach the calibration card on the printing screen, and press Settings →Print Settings→ Z axis movement →Leveling, Check whether the platform ﬁts evenly with the paper by referring to the steps on Page 8.
After conﬁrming that the calibration card ﬁt evenly, lock the four screws of the platform.

Note: The platform has been levelled at the factory. If it needs levelling due to transportation or other reasons, please follow the steps below to adjust the printing platform.

CREALITY-CL-79-SM-001-3D-Printer-fig-8

Note: The platform has been levelled at the factory. If it needs levelling due to transportation or other reasons, please follow the steps below to adjust the printing platform.

Load Resin

Pour the UV-photosensitive resin into the resin vat. The slot capacity is 250ml/450ml/650ml.

CREALITY-CL-79-SM-001-3D-Printer-fig-9

Tips: How to change resin?
Take out the resin vat slowly, pour out the remaining resin into the container, clean the resin vat, pour in new resin,and then install the resin vat to the machine.

Caution : Resin may cause skin irritation or an allergic skin reaction. Please wear gloves before use to avoid direct contact with the skin.

Release Film (FEP) Replacement

CREALITY-CL-79-SM-001-3D-Printer-fig-10

a. First, remove the 14 screws at the bottom of the tray and take out the broken release film (FEP).
b. Then place the release film between the two steel frames.
c. Finally, put the assembled steel frame back into the tray and tighten 14 screws.
d. The installed release film is as shown

CREALITY-CL-79-SM-001-3D-Printer-fig-13

USB Disk Printing

Slicer

CREALITY-CL-79-SM-001-3D-Printer-fig-15

Open the slicer software of HALOT BOX, click “Open” on the top left of the screen and add model ﬁle;
If the model needs to add support, click the upper left icon① to set the corresponding parameters②.
Click icon ①→Setting slice printing parameters②→ Click
Click icon ①→Setting slice printing parameters②→ Click

Note: The UI interface is for reference only, and shall be subject to the actual UI may be diﬀerent.

Print

CREALITY-CL-79-SM-001-3D-Printer-fig-17

Generate cxdlp ﬁle and save the ﬁle to U disk
Insert the USB disk

Note : The UI interface is for reference only, and shall be subject to the actual UI.

Warning: During the printing process the machine can’t be shaken, so as not to avoid inﬂuencingaﬀect the printing quality.

CREALITY-CL-79-SM-001-3D-Printer-fig-18

Select USB disk ﬁles;
Choose to use parameters；
Press the “Start” button
Printing·

Note: The UI interface is for reference only, and shall be subject to the actual UI. The machine stores the ﬁle being printed by default.

Creality Cloud Online

Make sure WiFi is correctly connected before using online printing Steps: Settings → WiFi → Select the corresponding WiFi.
Warm Tips : ① Only 2.4GHz WiFi is applicable to the 3D printer, and it cannot be connected to 5GHz WiFi routers; ② Only WPA-PSK/WPA2-PSK security protocol is applicable to the 3D printer, and other protocols may result in the failure to connect the printer to WiFi properly. To change the security protocol, users may change it in settings interface of the router.

CREALITY-CL-79-SM-001-3D-Printer-fig-20

Click Creality Cloud, online model；
Select the model;
Download the model;
Choos to use parameters；
Click “Start” to print.

Note: View and set printing parameters The UI interface is only for reference to the actual UI.

Creality Cloud App Print

CREALITY-CL-79-SM-001-3D-Printer-fig-22

Download
Register
Add equipment
Scan QR Code Settings → Detail → Connect to Creality Cloud → QR code
Device naming
Select the model, set the printer and parameters, and click “Slice”.
Upon completion of slicing, click “Printer”.
Select device
Print progress

Notes:

The steps for adding devices vary for different mobile phone operating systems;
Set the correct area in “Settings – Other Settings – Language and Area”.
Make sure WiFi is correctly connected before using online printing.

WIFI Print

Slicer

CREALITY-CL-79-SM-001-3D-Printer-fig-24

Open the slicer software of HALOT BOX, click“open” on the left of the screen and add model ﬁle.
If the model needs to add support, click the upper-left icon to set the corresponding parameters.
Click icon ①→Setting slice printing parameters②Click.
wait for a slice to be ﬁnished→Select “Remote Printing” for WiFi printing.
Once the transmission is over, select the ﬁle on the machine to start printing.

Note: Make sure the HALOT BOX and the printer are connected to the same WiFi.

Wiring Connection

CREALITY-CL-79-SM-001-3D-Printer-fig-27

Troubleshooting

CREALITY-CL-79-SM-001-3D-Printer-fig-28

FCC Statement

FCC Caution:
Any Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit diﬀerent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body.

IC Caution：

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

This device may not cause interference; and
This device must accept any interference, including interference that may cause undesired operation of the device. To maintain compliance with RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Due to the differences between different machine models, the actual objects and the images can differ. Please refer to the actual machine. The final explanation rights shall be reserved by Shenzhen Creality 3D Technology Co., Ltd.