Creality 3D LD-002R 3D Printer User Manual

: June 3, 2024
: Creality 3D

Creality 3D LD-002R 3D Printer

Dear Consumers,
Thank you for choosing our products.
For the best experience, please read the instructions before operating the Printer. Our teams wiss always be ready to render you the best services. Please contact us via the phone number or e-mail address provided at the end when you encounter any problem with the Printer.
For a better experience in using our product, you can also learn how to use the printer in the following ways:
View the accompanied instructions and videos in the U disk .
Visit our oﬃcial website www.creality.com to ﬁnd relevant software/hardware information, contact details and operation and maintenance instructions.

Firmware Upgrade
Please login the oﬃcial website https://www.creality.com/download, switch the language and select the relevant printer and model and download the required ﬁrmware, you can use it after the installation is ﬁnished.

NOTES

Do not use the printer any way other than described herein in order to avoid personal injury or property damage.
Do not place the printer near any heat source or ﬂammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.
Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.
Please use recommended resin to in case damage of machine.
Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.
Please do not open the plastic cover during usage, otherwise the printing will be interrupted.
Do not wear cotton gloves when operating the printer. Such cloths may become tangled in the printers moving parts leading to burns, possible bodily injury, or printer damage.
Please wait a moment after the print is ﬁnished. And please wear gloves to take out the print by tools.
Clean the printer frequently. Always turn the power oﬀ when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other material oﬀ the frame, guide rails, or wheels. Use glass cleaner or isopropyl alcohol to clean the print surface.
Children under 10 years should not use the printer without supervision.
Tips ：Do not plug or unplug the power cord when power on.
Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Realty will not be responsible for any violators’ legal liability under any circumstance.

Introduction

Creality-3D-LD-002R-3D-Printer-01

Torx head thumb screw
Leveling screw
Platform plate
Tray ﬁxing screw
Resin vat
Touch screen
Limit sensor
Air ﬁlter

Equipment parameters

Basic Parameters

Package Content

Creality-3D-LD-002R-3D-Printer-02

Assemble the 3D Printer

Creality-3D-LD-002R-3D-Printer-03

Interface Information

Creality-3D-LD-002R-3D-Printer-04

Note: View and set printing parameters, the UI information is only for reference , the actual UI may be diﬀerent.

Interface Information

Creality-3D-LD-002R-3D-Printer-05

Note: Check whether the light source is normal ，the UI information is only for reference , the actual UI may be diﬀerent.

Level Platform

Creality-3D-LD-002R-3D-Printer-06

To calibrate the printing platform, ﬁrst raise the platform, loosen the ﬁxing screws on the left and right sides of the material trough, and take out the material trough;
Loosen the four screws on the connecting plate of prototyping platform, attach A4 paper tightly to the print screen, press Settings → Z Axis Motion → Levelling（ Refer to operating steps of levelling platform 2 for operation.）, to check whether the platform ﬁts evenly with the paper.
After conﬁrming that A4 paper ﬁts evenly with the platform, screw up the four screws of the platform.

Note: The printing platform has been leveled at the factory. If it needs leveling due to transportation or other reasons, please follow the steps below to adjust the printing platform.（ Please bring ﬂat A4 paper by yourself ）

Level Platform

Creality-3D-LD-002R-3D-Printer-07

Note: The UI information is only for reference , the actual UI may be diﬀerent.

Load Resin

Pour the UV photosensitive resin into the resin vat. The slot capacity is 140ml/170ml/225ml/285ml.

Tips: How to change resin:
Take out the resin vat slowly, pour out the remaining resin into the container, clean the resin vat, pour in new resin, and then install the resin vat to the machine.

Tips: Resin may cause skin irritation or an allergic skin reaction. please wear gloves before use to avoid direct contact with the skin.

Release Membrane Replacement

First, remove the 14 screws at the bottom of the tray and take out the broken release ﬁlm.
Take a new release ﬁlm, tear oﬀ the protective ﬁlms on both- sides of the release ﬁlm, and then place the release ﬁlm bet- ween the two steel rings.
Finally, put the assembled steel frame back into the tray and tighten 14 screws.
The installed release ﬁlm is as show.

Start Printing

Slice
Open the slice software of LCD 3D printer, click“ open” on the left of the screen and add model ﬁle.
If the model needs to add support, click the upper right icon to set corresponding parameters.
Click icon ①→Setting slice printing parameters②→ Click“ Slice” ( recommend to set parameters of bottom layer as 5-20).
waiting for slice to be ﬁnished →save the sliced ﬁle You are welcome to ﬁnd more details of slicing tutorial on the oﬃcial website www.creality.com).
Print
Generate clop ﬁle ，and save the ﬁle to U disk
Insert the U disk →Select a document → Press the start button

Warning: During the printing process, the machine can not be shaken, so as not to aﬀect the printing quality.

Start Printing

Select ﬁles;
Select the ﬁle to be printed and press “Start”;
Printing···

Note: The UI information is only for reference , the actual UI may be diﬀerent， The machine stores the ﬁle being printed by default.

Control remote printing

Download
Register
Log in
Add equipment
Scan QR Code
Device naming
Select device
check printing status
Print Progress

Wiring Connection

Troubleshooting

Creality-3D-LD-002R-3D-Printer-19

FCC Statement

FCC Caution:
Any Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.