CREALITY D1 DIY 3D Printer User Manual

CREALITY D1 DIY 3D Printer

Specifications:

• Power: 350W
• Profile: 2040
• Screw Type: M4*14 hexagon socket head cap screws, T-type Screw Rod T, M5
• Leveling: Z-axis adjustment
• Printing Platform Size: 280mm x 260mm x 310mm

Product Usage Instructions

Installation:

1. Install the 2040 profile using four M4*14 hexagon socket head cap screws.
2. Insert the printing platform into the component installed in the second step.
3. Install the T-type Screw Rod T.

Leveling Instructions:

1. For the first leveling, set the Z-axis to move down by 10mm and remove the motor (Z10mm).
2. Press the printing platform to the bottom, move up 10mm in Z-axis, and return the motor to zero (Z10mm).

FAQ:

• Q: What size is the printing platform?
  A: The printing platform size is 280mm x 260mm x 310mm.

• Q: What type of screws are used for installation?
  A: Four M4*14 hexagon socket head cap screws are used for installing the 2040 profile.

3D Printer User Manual

Dear Consumers,

• Thank you for choosing our products. For the best experience, please read the instructions before operating the Printer. Our teams will always be ready to render you the best services. Please contact us by phone number or e-mail address provided at the end when you encounter any problem with the Printer.
• For a better experience in using our product, you can also learn how to use the Printer in the following ways:
• View the accompanied instructions and videos in the storage card.
• Visit our official website www.creality.com to find relevant software/hardware information, contact details and operation and maintenance instructions.

NOTES

1. Do not use the printer any way other than described herein in order to avoid personal injury or property damage.
2. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.
3. Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.
4. Before using experimental or exotic filaments, we suggest using standard filaments such as ABS or PLA to calibrate and test the machine.
5. Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.
6. Do not touch the nozzle or printing surface during operation as they may be hot. Keep hands away from machine while in use to avoid burns or personal injury.
7. Do not wear gloves or loose clothing when operating the printer. Such cloths may become tangled in the printers moving parts leading to burns, possible bodily injury, or printer damage.
8. When cleaning debris from the printer hooted, always use the provided tools. Do not touch the nozzle directly when heated. This can cause personal injury.
9. Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other material off the frame, guide rails, or wheels .  Use glass cleaner or isopropyl alcohol to clean the print surface before every print for consistent results.
10. Children under 10 years of age should not use the printer without supervision.
11. This machine is equipped with a security protection mechanism. Do not manually move the nozzle and printing platform mechanism manually while booting up, otherwise the device will automatically power off for safety.
12. Users shall comply with related nation and region’s laws, regulations and ethical codes where the equipment or produced prints by it is used, and users of our product shall not use aforesaid products to print any end-use products, objects, parts or components or any other physical prints that violate the national or regional laws, regulations and ethical codes where herein referred product and produced prints by it is located.

Equipment Introduction

1. Corrugated pipe
2. Profile cover
3. Printing platform
4. Leveling nut
5. 5 Front door
6. Display screen ST
7. Filament guide support
8. Filament detecting kit
9. Spool holder
10. Storage card
11. Nozzle kit
12. Power supply

Equipment Parameters

Model| Sermoon Dl
Printing Size I J5xll:iR’J| 2so•250•31omm
Molding Tech| FDM
Nozzle Number| 1
Slice Thickness| 0.lmm-0.4mm
Nozzle Diameter| Standard 0.4mm
Precision| ±0.lmm
Filament| PLA
File Format| STL/OBJ/AMF
File Transfer| USS/Storage card =
Slice Software’| Creativity Slicer
Rated Voltage|

• Input AAC100-240V 50/60Hz
• Output :DC 24V

Total Power I W)’.(Er}J!¥| 350W
Bed Temp| 100°C
Nozzle Temp|  260°C
Resume Print| Yes I
Daul Z-Axis| Yes I
Language I| Chinese/English
Operating System| Windows XP/Vista//7/8/10 MAC/Linux
Printing Speed| Normal 30-60mm/s

Parts List

TOOLS LIST

Install Profile

Take out the components for the bottom, take apart the frame lid and then install the four section bars. Install based on the position of the digital tag and the direction of the arrow, use a No. 3 wrench to tighten the M6*35 hexagon socket head screws and M6 flat washers from the base to fix the four profiles.

Please pay attention to distinguish four kinds of profiles:

• Profile 1 : 3 fixed plates installed on the left;
• Profile 2: 3 fixed plates installed on the right;
• Profile 3: 3 fixed plates installed on the left and right respectively (symmetric);
• Profile 4: 3 fixed plates installed on the left and right respectively (asymmetric);

Install 2040 Profile

Install the 2040 profile with four M4*14 hexagon socket head cap screws are used to;

Install the Printing Platform
Insert the printing platform into the component installed in the second step;

After installation, please check the tightness between v-wheel and profile to avoid idling of v-wheel.

• Install the T-type Screw Rod
  • Install the T-type screw rod and tighten the screw between the T-type screw rod and coupling.

Install the Top Frame and Filament Guide Support

1. Install the filament guide support with M4*6 screws as shown in this figure;
2. Install and orientate the top frame, Using M6*35 screws and M6 flat gaskets to orientate the four profiles and top frame;
3. Use the M4*14 flat round head screw to lock the 2 profiles on left and right according the circle icon position.

Wire Connection
Connect all wires by color and marking(as shown in the figure)

• Caution
  • Select the correct input voltage to match your local mains
  • (AC100-240V)
  • Damage can occur if voltage is set incorrectly.
  • Do not connect or disconnect the cables when the machine is powered on.

Arrange the Wiring Harness
According to the real demand, tie the wire harness well with ribbon (as shown in the picture}.

Install the Left Daffl e

Before installing, remove the protective film on the door

Install the Back Baffle
Before installing, remove the protective film on the door

Install the Right Baffle and Filament Tube

1. Before installing the right dam-board, use 2 *8 screws to fix the rack on the right rear profiles and talkie the barrel through the rack,
   tighten the screw to fix the barrel;

2. As shown in this figure, lock tight 8 M4*8 screws and install the dam-board on the right.
   Before installing, remove the protective film on the door.

Install the Front Door

Install the Profile Cover and Power Cable

Bed Leveling

• For the first leveling : Set the Z-axis → move down 10mm → remove the motor

Note: The Ul information is only for reference, the actual Ul may be different.
Press the printing platform to the bottom→ move up 10mm in Z-axis → return the motor to zero.

Note: The Ul information is only for reference. the actual Ul may be different..
“Leveling” — Aid-leveling and click D/2/3/4/5.
Note: The Ul information is only for reference, the actual Ul may be different.

• Move the nozzle near the top of the leveling screw, twist the screw left or right to make the distance between the nozzle and the platform is as thick as a piece of A4 paper. Leveling the four corners in order, click CD to verify .whether the gap between the nozzle and the platform is proper or not.
• Use a piece of A4 paper (standard printer paper) to assist with the adjustment, making sure that the nozzle lightly scratches the paper. Complete the adjustment of the screw on all 4 corners. Repeat above steps 1-2 times if necessary. Keep adjusting until there is slight resistance on the A4 paper from the nozzle.
  

Preheating

When you wait for the temperature to rise, hang the filament over the filament holder

Load Filament

Put the filament into the filament detector, pass through the two wheels of the filament guide support, When the temperature reaches at the target temperature pressing the extruder spring. Insert the filament into the extrude small hole till the nozzle position. When the filament comes out from the nozzle it means the filament has been loaded successfully.
Please fix the filament tube on the corrugated pipe with a tie and dress the filament through the middle of the tube if you need to hoist the Siemen

Tips: How to replace the filament?

1. Cut filament near the Extruder and slowly feed in the new filament to the material tube.
2. After preheating the nozzle, push the filament a little forward and quickly withdraw the filament, and then feed in the new filament.

Start Printing

• Double click to install the software,
• Double click to open the software,
• Open Creality 3D slicer ➔ Load (Read file) ➔ Select file.

• Generate G-code, and save the geode file to storage card.
• lnsert the storage card➔ Print
  • File names must be Latin letters or numbers, not Chinese characters or other special symbols
  • Notes: For details on the software instructions, please refer to the slicing software manual in the memory card!

Wiring connection

Troubleshooting

Notes

• Due to the differences between different machine models, the physical objects and the final images can differ. The final explanation rights shall be reserved by Shenzhen Creality 3D Technology Co., Ltd.
  • SHENZHEN CREALITY 3D TECHNOLOGY CO.,LTD. 11F & Room 1201, Block 3,JinCheng Yuan, Tongsheng Community, Dalang, Longhua District,Shenzhen,China,518109 Official Website:
  • www.creality.com
  • Tel: +86 755-8523 4565
  • E-mail: info@creality.com
  • cs@creality.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>