FEZEN ZM1515 Cold Press Juicer User Manual
- June 14, 2024
- FEZEN
Table of Contents
FEZEN ZM1515 Cold Press Juicer
Product Information
- Model: ZM1515
- Input Voltage: AC220-240V50Hz
Safety Precautions:
- Confirm socket voltage before use.
- Do not sterilize parts in hot water above 80°C or in a microwave oven.
- All parts in contact with food should comply with hygiene standards and be cleaned thoroughly before use.
- Do not immerse or rinse the main body in liquid.
- Avoid cleaning with steel wool, abrasive agents, or corrosive liquids.
Parts and Functions:
No. | Parts |
---|---|
1 | Power cord |
2 | Main body |
3 | Power switch |
4 | Button |
5 | Juicing body |
6 | Spiral pusher |
7 | Juice strainer |
8 | Squeezer |
9 | Juice cup |
10 | Residue cup |
11 | Food tray |
12 | Pushing rod |
13 | Removal wrench |
Product Usage Instructions
Before First Use:
Clean parts in direct contact with food thoroughly. Refer to Chapter 4: Maintenance for cleaning instructions.
Switch Operating Instructions:
- Rev: Activates reverse motion to discharge blockage or when the motor is locked.
- O: Shuts down the appliance.
- Soft: For soft ingredients.
- Hard: For hard ingredients.
Installation Guide:
- Connect the juicing body to the main body:
- Align the triangular aligning mark on the main body to latch the juicing body onto the main body (the 3 clips on the juicing body will realize alignment).
- Turn the juicing body in an anticlockwise direction until a click is heard, indicating the connection is completed.
- Align the hexagonal shaft of the spiral pusher with the hole on the main body and push it horizontally until it reaches the bottom. If alignment fails, slightly adjust the spiral pusher.
- Fit the larger end of the juicer strainer into the tail of the spiral pusher and push it when the 3 clips of the juicer strainer align with the 3 clamping slots in the juicing body. (Note: The juice strainer is used with the juicing button in the rear only for juicing purposes.)
- Align the triangular alignment mark on the squeezer with the arrow on the juicing body. Turn it anticlockwise to align with the unlock triangular mark on the juicing body.
- Position the juice cup in the corresponding groove on the main body, aligning its opening below the juice outlet of the juicing body.
- Position the residue cup below the residue outlet of the juicing body, close to the juice cup.
- Connect the appliance to the power supply. Make sure the power switch is in the OFF position before connecting.
- Wash vegetables and fruits, cut them into sizes fitting the inlet of the feed port, and place them on the food tray.
- Press the Soft/Hard button and operate the appliance for no longer than 10 minutes per usage.
- Feed food ingredients into the feed port and guide them downwards with the pushing rod.
Maintenance:
Before cleaning, ensure that the power switch is in the ON position and disconnect the power supply.
Safety Precautions
- The input voltage of the appliance is AC220-240V~50Hz. Please confirm your socket voltage before connecting the power supply.
- Disconnect the power supply before dismantling, assembling or adjusting any part of the appliance.
- The appliance comes equipped with a“Y connection”, If the power cord is damaged, please contact our customer service or have it directly replaced at your nearest authorized service center. Do not attempt to dismantle and repair it by yourself to avoid injuries or damages.
- Before operating the appliance, please check if the power cord, the plug, the juice strainer, the spiral pusher and any other part is damaged. If any of the said part is damaged, do not operate the appliance and contact our customer service immediately. Do not attempt to dismantle and repair it by yourself to avoid injuries or damages.
- For repair and servicing, please contact our customer service or have it directly repaired at your nearest authorized service center. Do not attempt to dismantle and repair it by yourself to avoid injuries or damages.
- Please ensure that the juicing body, spiral pusher, juicing body cap and all other dismountable parts are properly installed before connecting the power supply.
- Do not insert hands or sharp objects into the feed port and avoid touching the spiral pusher when the appliance is running to prevent injuries and damages; never replace the spiral pusher with any other objects and observe a safe distance between your eyes and the feed port to avoid accidents.
- Prepare food ingredients in sizes smaller than the feed port for ease of entry. Do not process any vegetables or fruits with pits, hard seeds, thick skin or shells until they are completely removed.
- When feeding a food ingredient into the feed port, do not exert excessive force but just enough to cut the food ingredient.
- Discoloration of juice strainer, juicing body cap, spiral pusher and other accessories after juicing of certain vegetables or fruits is normal, and will neither affect food quality nor harm your health.
- Equipped with an intelligent protective chip, the appliance will shut down automatically after 20 minutes of continuous running. In the event, wait for 20-30 minutes until the motor has cooled down before resuming operation to prolong the service life of the appliance.
- The appliance has a current limiting design. Hence, the motor would be locked and the current would rise when hard food ingredients are processed. When the current is higher than 1.3A, the motor would be alerted and pause for 2 seconds before reversing automatically for 5 seconds and finally shutting down (food causing obstruction in the appliance would be discharged when the motor reverses). At this point, hit the “ON” button to resume normal operation of the appliance.
- In the event of activation of current limiting, locking of motor or failure of auto reverse, hit the “OFF” button to shut down the appliance, followed by the “REV” button to discharge any obstruction, and finally hit the “ON” button again to resume normal operation of the appliance. If the motor is still locked, it is recommended that anyobstruction in the spiral pusher should be removed before resuming operation of the appliance. This action serves to protect the motor.
- Do not dismantle the dismountable parts of the appliance immediately after use. Make sure both the motor and spiral pusher have come to a complete stop with the power supply disconnected before dismantling.
- Do not sterilize any parts in hot water with a temperature higher than 80℃ or in a microwave oven. It would lead to permanent deformation and damage. All parts coming in direct contact with food ingredients should complywith food hygiene standards and be cleaned thoroughly before use.
- Do not immerse the main body or rinse it under running water or any liquid to prevent damages.
- Do not clean the appliance with steel wool, abrasive cleaning agents or corrosive liquids (such as gasoline or acetone).
- Store this appliance out of reach of children. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by persons lacking experience and knowledge unless under professional guidance and close supervision.
- The appliance is intended for use by individuals or families only.
- Do not leave children unsupervised with this appliance.
- Parts, other than those supplied with the appliance, include safety instructions.
- Do not clean surfaces or parts that come in direct contact with food ingredients when the appliance is connected to the power supply.
- Do not replace or touch moving parts before the appliance is completely shut down and disconnected from power.
- This portable appliance is designed for domestic and indoor use only.
- If the power cord is damaged, it must be replaced by the manufacturer, at an authorized service center or by an authorized service representative to avoid hazards.
- Warning: potential dangers may arise if appliance is misused.
- Always disconnect the power if it is left unattended and before assembling, dismantling or cleaning.
- Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
Parts and Functions
No. | Parts | Functions |
---|---|---|
1 | Power cord | It is used for connecting the power supply to provide power. |
2 | Main body | As a main part and the power source of the appliance, |
3 | Power switch | It controls the operating statuses (Rev, O, Soft, Hard) of |
the appliance.
4| Button| It is used for locking the juicing body to prevent it from
detaching from the
main body during operation.
5
| ****
Juicing body
| It is the main part for juicing. Food ingredients are first fed via the feed port at
the top of the juicing body and then discharged in forms of juice and pulp via the juice outlet and the pulp outlet respectively.
6| Spiral pusher| As a main part for juicing, it is used for grinding food
ingredients by breaking
| | and conveying them to the juice strainer or the squeezer.
---|---|---
7| Juice strainer| Using Squeezing with the spiral pusher, it used for
grinding and filtering the
extracted food ingredients to obtain the juice.
8| Squeezer| It is used for grinding food ingredients by Squeezing with the spiral pusher
(for fruits and vegetables).
9| Juice cup| It is used for juice collection.
10| Residue cup| It is used for residue collection.
11| Food tray| It is mainly used for placing food ingredients.
12| Pushing rod| It is used for guiding food ingredients from the feed port to
the spiral pusher
for higher juice extraction efficiency.
13| Removal wrench| For disassembly of parts 8
Directions for Use
Before operating the appliance for the first time, clean the parts that come
into direct contact withfood ingredients thoroughly (please refer to “Chapter
4: Maintenance”).
Installation Guide
Please install the appliance by following the steps below:
Maintenance
- Before cleaning the appliance, make sure the power switch is at the“ON” position and disconnect the power supply.
- Clean the appliance immediately after each use.
- Do not rinse the main body under running water but wipe away any stains with a damp cloth.
- Before storing the appliance, make sure it is clean and dry.
- Clean the appliance after dismantling by following the steps below.
Safety Indexes
Rated voltage | 120V~ |
---|---|
Rated power | 150W |
Rated frequency | 50Hz |
Continuous operating time | ≤10 min. |
Operation intervals | ≥10 min. |
Notes:
The analysis and elimination methods illustrated in this manual are merely
indications of common faults. For any other faults, please contact our
customer service or have the appliance directly repaired at your nearest
authorized service center. Do not attempt to dismantle and repair it by
yourself to avoid hazards