CyberPower CPS160PBURC1 Power Inverters Owner’s Manual

: June 15, 2024
: CyberPower

Table of Contents

CyberPower CPS160PBURC1 Power Inverters
Product Information
Product Usage Instructions
FEATURES
SPECIFICATIONS
IMPORTANT SAFETY INFORMATION
FUSE REPLACEMENT
TROUBLESHOOTING
CONFORMANCE APPROVALS
FOR MORE INFORMATION
TECHNICAL SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CyberPower CPS160PBURC1 Power Inverters

Product Information

Specifications:

Model: CPS160PBURC1
Input Voltage: 13.8 Volts
Output Peak Power: 160 Watts
Output Continuous Power: 100 Watts
AC Output: 120 V/60 Hz/Simulated Sine Wave
USB-A Charging Output: 5 V/2.4 A Max
Protection Features: Low Voltage, Overheating, Overload, Short Circuit

Features:

Power Plug
AC Outlet (1)
USB-A Charging Port (1)
Cooling Fan Vents

Important Safety Information:
Before installing and using the CyberPower AC/DC Power Inverter, please read and follow these safety instructions:

Fuse Replacement:
Unplug the inverter from the DC power outlet.
Disassemble the DC plug as pictured.
Replace the 15 amp fuse.
Reassemble the DC plug as pictured.

Product Usage Instructions

Fuse Replacement:

Unplug the inverter from the DC power outlet.
Disassemble the DC plug as pictured in the user manual.
Replace the 15 amp fuse with a new one.
Reassemble the DC plug as pictured in the user manual.

Troubleshooting:

Problem	Possible Cause	Suggested Solutions
Poor contact with the DC power outlet.	Ensure the inverter is securely

plugged into the vehicle’s DC
power outlet.| Check and ensure proper connection.
The automotive electrical system requires ignition to be on.| Turn the vehicle ignition to the Accessory position.| Switch the vehicle ignition to the Accessory position.
The car’s DC power outlet fuse is blown.| Check the vehicle fuse panel and replace the damaged fuse.| Inspect and replace the blown fuse in the vehicle fuse
panel.
No AC output power Overheating.| The vehicle’s battery voltage is below 11 volts. The vehicle’s battery
input voltage is higher than 15 volts. The inverter is overloaded.| Allow the inverter to cool. Ensure adequate ventilation around
the unit and load does not exceed the unit’s Continuous Power
rating (see specifications).
Unplug the inverter and start the vehicle to charge the
battery.| Check your vehicle’s user guide for troubleshooting.| Refer to the vehicle’s user guide for troubleshooting
steps.
Ensure the load does not exceed the unit’s Continuous Power rating
(see specifications).| | Check the load and ensure it does not exceed the unit’s
Continuous Power rating.

For More Information:

Technical Support:

Visit: CyberPowerSystems.com/support
Toll-Free: 1-877-297-6937

Conformance Approvals:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined

FAQ:

Q: What are the protection features of the AC/DC power inverter?
A: The AC/DC power inverter has protection features for Low Voltage, Overheat, Overload, and Short Circuit.
Q: Where can I find technical support for the product?
A: You can visit CyberPowerSystems.com/support or call toll-free at 1-877-297-6937 for technical support.

FEATURES

Power Plug
AC Outlet (1)
USB-A Charging Port (1)
Cooling Fan Vents

SPECIFICATIONS

Model: CPS160PBURC1
Input Voltage: 13.8 Volts
Output Peak Power: 160 Watts
Output Continuous Power: 100 Watts
AC Output: 120 V/60 Hz/Simulated Sine Wave
USB-A Charging Output: 5 V/2.4 A Max
Protection Features: Low Voltage, Overheating, Overload, Short Circuit

WARNING:
This product can expose you to chemicals including bisphenol A (BPA) and styrene (ABS), which is known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.

IMPORTANT SAFETY INFORMATION

BEFORE INSTALLING AND USING THE CYBER POWER AC/DC POWER INVERTER, PLEASE READ AND FOLLOW THESE SAFETY INSTRUCTIONS:

DO NOT operate the CPS160PBURC1 near ﬂammable materials, ﬂumes, or gases.
Always use the inverter where there is adequate ventilation.
DO NOT obstruct the ventilation slots.
Never immerse the unit in water.
Proper cooling is essential when operating the inverter. Refrain from placing the inverter near the vehicle’s heat vent or in direct sunlight.
Always turn the inverter off when not in use by removing it from the DC accessory port.
Check the warning labels on battery chargers or adapters before connecting them to the inverter. DO NOT connect battery chargers or adapters that have warnings about using with inverters.

FUSE REPLACEMENT

Unplug the inverter from the DC power outlet.
Disassemble the DC plug as pictured.
Replace the 15 amp fuse.
Reassemble the DC plug as pictured.

TROUBLESHOOTING

Problem	Possible Cause	Suggested Solutions
No AC output power

Poor contact with the DC power outlet.

| Ensure the inverter is securely plugged into the vehicle’s DC power outlet.
The automotive electrical system requires ignition to be on.| Turn the vehicle ignition to the “Accessory” position.
The car’s DC power outlet fuse is blown.| Check the vehicle fuse panel and replace the damaged fuse.

Over-heating.

| Allow the inverter to cool. Ensure that there is adequate ventilation around the unit and load does not exceed the unit’s Continuous Power rating (see speciﬁcations).
The vehicle’s battery voltage is below 11 volts.| Unplug the inverter and start the vehicle to charge the battery.
The vehicle’s battery input voltage is higher than 15 volts.| Check your vehicle’s user guide for troubleshooting.
The inverter is overloaded.| Ensure the load does not exceed the unit’s Continuous Power rating (see speciﬁcations).

CONFORMANCE APPROVALS

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.