CLEAR DESIGN THREE60 Conference Table Instructions
- June 9, 2024
- CLEAR DESIGN
Table of Contents
CLEAR DESIGN THREE60 Conference Table
General Installation Guide
S1:
SITTING HEIGHT
OVERVIEW
THREE60 Conference Table
Quantities are for a 48” x 216” table, parts may vary depending on project,
but install steps will remain the same.
PARTS LIST
| CODE | QTY | DESCRIPTION |
|---|
GCNAB
| ****
2
| ****
Angled Sleigh Leg
| ****
**** CNS48144
| 1| Trapezoid Surface|
2| In-Surface Grommet|
CNCGB| 2| Center Grommet Spacers|
2| In-Surface Grommet| ****
CNCBV2
| ****
4
| ****
Cabinet Base
| ****
BFB1
| ****
6
| ****
Flat Bracket
| ****
GCNABCOV*
| ****
4
| ****
Covered Leg
| ****
*If applicable.
-
PREPARE SURFACE AND MEASURE FOR LEGS
Carefully place surface upside-down on floor, a cushioned area is preferred. Measure 12” from surface edge and center-align to determine leg placement.
NOTE: Same process for square-ended table.
-
SECURE ANGLED SLEIGH LEGS
Follow measurements and insert screws per leg through the metal plate and into the laminate surface.
- MEASURE FOR CABINET BASE OR COVERED LEG
Place cabinet base, or covered leg, centered under the table grommet cutouts.
- INSTALL CABINET BASE OR COVERED LEG
Insert 4 screws per base through the laminate top into the bottom of the surface.
-
ATTACH HARDWARE TO SURFACE EDGE
Insert 2 wooden dowels, attach 2 flat brackets, and connect 4 sets of joint fasteners to one side of each surface edge.
-
FLIP AND ASSEMBLE
Flip each piece over so that it is standing on a leg/cabinet base. Align the open holes on the surface edge with the wooden dowels and the threaded rods on the other surface edge.
- FULLY SECURE HARDWARE
- INSTALL GROMMETS
Insert wire management grommet.
S2:
STANDING HEIGHT
OVERVIEW
THREE60 Conference Table
All parts listed are for a single standing height table; additional parts will
be needed for additional standing height table.
| CODE | QTY | DESCRIPTION |
|---|---|---|
| GCNABSH | **** |
2
| Standing Height Angled Sleigh Leg|
CNS4896| 1| Main Surface|
1| In-Surface Grommet|
GCNABSHLE| 2| Support Brace|
BFB1| 2| Flat Brackets| ****
-
PREPARE SURFACE
Carefully place surface upside-down on floor, a cushioned area is preferred. Measure 12” from surface edge and center-align to determine leg placement. Attach 2 flat brackets on the center seam of the table.
NOTE: Leg placement may need to be adjusted based on surface size .
-
INSTALL ANGLED SLEIGH LEGS
Follow measurements and insert 15 screws per leg through the metal plate and into the laminate surface.
-
INSTALL SUPPORT BRACE
-
FLIP AND INSERT GROMMET
Insert wire management grommet.
Note: See page 13 for optional covered sleigh leg. See page 15 for power module install.
OPTIONAL COVERED SLEIGH LEG
All steps for installation are the same. However, leg will be aligned with the
grommet cutout on the table.
NOTE: Covered sleigh leg is optional for wire management. 
S3: OPTIONAL POWER
OVERVIEW
THREE60 Conference Table
| CODE | QTY | DESCRIPTION |
|---|---|---|
| BPCONF2V2 or BPCONF3 | 1 | In-Surface Power Module |
JC1| 5| J-Clips| **
VB24| 1| Cable Vertebrae|
-
ATTACH METAL CLIPS AND INSERT INTO SURFACE
Attach 2 metal clips to the back of the module base then insert into the pre- cut holes in the surface. -
SECURE MODULE INTO PLACE
Insert the plastic clamps into the holes on the bottom of the module. Rotate and then push against the surface to clamp the module into place. -
OPTIONAL POWER VERTEBRAE
Attach the vertebrae to the underside of the top panel. Insert wood screws through the top bracket and into the laminate panel.
NOTE: Power vertebrae will be mounted adjacent to the power module.
1-866-304-7197 |
inspire@mycleardesign.com |
mycleardesign.com
© 2022 Clear Design | Version 22.1.5
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>