ULTIMEA Apollo P50 Smart Projector User Manual

ULTIMEA Apollo P50 Smart Projector

Product Information

• Specifications:
  • Model No.: U0330
  • Power Supply: AC power port
  • Ports: USB, HDMI, AV, 3.5mm, USB RJ45
  • Projection Distance: 2.49m – 3.73m
  • Projection Image Size: 80 inches – 120 inches
• Safety Instructions:
  • Read all instructions before using the device.
  • Do not make any changes or settings not described in the manual.
  • Failure to follow instructions may result in physical injury, data loss, or damage that voids the warranty.
• Setup:
  • Plug the power cord into an outlet.
  • Press the power button to turn on the projector.

Get Started

• Prepare the Remote Control:
  • Ensure the remote control is ready for use by following these steps:
  • Insert batteries into the remote control.
  • Point the remote control towards the projector.
• Power On/Off:
  • To power on/off the projector:
  • Plug the power cord into an outlet.
  • Press the power button on the remote control to turn on/off the projector.
• Projection Distance and Projection Image Size:
  • The projector supports various projection distances and image sizes. Refer to the table below for recommended distances:

Product Introduction

• Auto Focus:
  • The projector has an auto-focus feature. However, you can also manually focus using the remote control:
  • Press the focus button on the remote control.
  • Observe the focus icon and adjust the picture until it is clear.
• Keystone Correction:
  • The projector supports automatic keystone correction and manual four-point keystone correction:
• Automatic Keystone Correction:
  • Press the button on the remote control.
  • Select [More Settings] -> [Projection Settings] -> [Keystone Correction] -> [Auto Keystone Correction].
  • Select “on”. The projector will automatically correct any skewed image to restore it to a rectangle.
• Manual Four-point Keystone Correction:
  • Press the button on the remote control.
  • Select [More Settings] -> [Projection Settings] -> [Keystone Correction] -> [Manual Four-point Keystone Correction].
• Zoom In/Out:
  • You can adjust the screen size using the zoom feature:
  • Press the button on the remote control.
  • Select [More Settings] -> [Projection Correction] -> [Digital Zoom].
  • Use the navigation buttons on the remote control to adjust the screen size.
• Intelligent Obstacle Avoidance:
  • The projector has an intelligent obstacle avoidance function:
  • Press the button on the remote control.
  • Select [More Settings] -> [Projection Correction] -> [Smart Recognition] -> [Intelligent Obstacle Avoidance].
  • Select the function to turn it on or off.
• Automatic Screen Alignment:
  • The projector supports automatic screen alignment:
  • Press the button on the remote control.
  • Select [More Settings] -> [Projection Correction] -> [Smart Recognition] -> [Automatic Screen Alignment].
  • Select the function to turn it on or off.
• Projection Settings:
  • The projector supports various projection modes:
  • Desktop Front Projection
  • Desktop Rear Projection
  • Ceiling Front Projection
  • Ceiling Rear Projection
  • To select the desired projection mode:
  • Press the button on the remote control.
  • Select [More Settings] -> [Projection Settings] -> [Projection Mode].
  • Select the desired mode.
• FAQ:
  • Q: Where can I find video tutorials and user manuals?
  • A: Video tutorials and user manuals are available on the ULTIMEA website at support.ultimea.com.
  • Q: How can I contact customer support?
  • A: You can reach customer support via email at support@ultimea.com or by phone at +1 888-598-8875 (US) or +49 89-628-25828 (EU) during Mon-Fri 9 am-5 pm (PST) or (CET) respectively.

Safety Instructions

• Read all instructions before you use this device. Do not make any changes or create settings that are not described in this manual. If physical injury, loss of data, or damage is caused by failure to follow instructions, the warranty does not apply.
• To avoid personal injury or property damage, please comply with the instructions in this manual carefully and do not use the product in any other way.
• To reduce the risk of fire and/or electric shock, do not expose the device to rain or moisture. Objects filled with liquids, such as vases, should not be placed on this device.
• Do not place this device on soft surfaces such as tablecloths or carpets, otherwise the device could be a fire hazard.
• Do not place this device in areas susceptible to excessive dust and dirt or near any appliance generating a strong magnetic field.
• To prevent overheating, do not block or clog the ventilation openings.
• Never place this device in a confined space. Always leave enough space around this device for ventilation.
• Avoid overexposing this device to direct sunlight, heat, large temperature fluctuations, and moisture. Avoid extreme temperatures.
• When this device is running for a long period of time, the surface may become hot. If this occurs, shut it down immediately and unplug the charger. Resume operation after the device has cooled down.
• Always handle this device with care. Avoid touching the lens.
• Do not allow children to handle the device without supervision.
• No not place heavy or sharp objects on this device.
• To avoid electric shock, do not disassemble the evice.
• Avoid extreme vibration. It may damage the internal components.
• Only use attachments or accessories specified by the manufacturer.
• Please comply with the laws and regulations of the country and region where the equipment is located (used), observe professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purpose.
• When using a projector in a dark environment, be mindful of the safety of your audience. Ensure that equipment such as projectors and power cords are placed in locations where they cannot be easily tripped over or touched, and avoid crossing cords to minimize safety risks.

Power Supply

• Use only the provided power adapter.
• Power off the device before removing the power supply from the socket.
• Protect the power cord from being walked on or pinched, particularly at plugs.
• Unplug this device if there are lightning storms or when unused for a long period of time.
• Before you make or change any connections, ensure that all devices are disconnected from the power outlet.
• Never touch the power cable or the power connector with wet hands.

Hearing Safety

• To prevent hearing damage, do not listen for extended periods at high volume. Set the volume to a safe level.

Caution

• Do not stare directly at the operating beam. The bright light may damage your eyes.

Cleaning

• Use a soft, lint-free cloth. Never use liquid, gaseous, or easily flammable cleansers to clean.
• Do not use any liquid cleaning agents to clean the lens to avoid damaging the coating film on the lens.
• Wipe the surfaces gently. Be careful that you do not scratch the surface.
• Use lens cleaning paper to clean the lens.

Repairs

• Do not make any repairs to this device yourself. Only have your device repaired by an authorized service center.
• Improper maintenance can result in injuries to persons or damage to this device.
• Refer all servicing to qualified service personnel.

System

• Due to regular updates to the Linux system interface and user interface updates through software upgrades, variations between the interface and the manual might arise.
• Should any disparities between the manual and the final product’s user interface occur, kindly rely on the actual on-screen display for accurate information.

What’s Included

Overview

Remote Control

LED Indication

Get Started

Prepare the Remote Control

• Open the battery holder cover of the remote control.
• Install two AAA batteries. Make sure to match the polarity (+/-) indicated and put back the cover.
• Please refer to the on-screen instructions to pair the remote control with the Apollo P50.
• The distance between the remote and the projector should not exceed 10 m/33 ft.

Power On/Off

• Inserting the power plug using the provided power cord.
• Press the power button or remote control power button once to power on.
• Press the power button or remote control power button twice to power off.

Placement

• Place Apollo P50 on a stable, flat surface in front of the projection surface.
• Please adjust the distance between Apollo P50 Smart and the projection surface to get the desired projection image.

Projection Distance and Projection Image Size

• Notice: The projection image size refers to the distance of the diagonal of the image size instead of the length of the image size.

Auto Focus

• Press the button, select [More Settings]->[Projection Settings]->[Autofocus Settings]->[Autofocus when moving], select on.
• Place the projector on a suitable projection surface or wall, and the projector will perform autofocus until it gets a clear image.

Manual Focus

• You can also manually focus through the remote control, press the focus button on the remote control, and observe the focus icon to adjust the picture until the picture is clear.

Keystone Correction

• The projector supports automatic keystone correction and manual four-point keystone correction.

Automatic Keystone Correction

• Press the button, select [More Settings]->[Projection Settings]->[Keystone Correction]->[Auto Keystone Correction], select on. When the projector image is skewed, it will perform auto keystone correction to restore the image to a rectangle.

Manual Four-point Keystone Correction

• If the projected image is stretched or distorted along both axes due to the projection angle, press the button, select [More Settings]->[Projection Correction]->[Keystone correction]->[Auto Keystone], select off.
• Select [4-Corner Correction], select the corner you want, and press the button on the remote control to adjust.

Zoom In/out

• Press the button, select [More Settings]->[Projection Correction]->[Digital Zoom], use the remote control navigation buttons to adjust the screen size.

Intelligent Obstacle Avoidance

• press the button, select [More Settings]->[Projection Correction]->[Smart Recognition]->[Intelligent Obstacle Avoidance], select the function on/off.

Automatic Screen Alignment

• Press the button, select [More Settings]->[Projection Correction]->[Smart Recognition]->[Intelligent Screen Alignment], select the function on/off.

Projection Settings

Press the button, [More Settings]->[Projection Settings]->[Projection Mode], select Desktop Front Projection/Desktop Rear Projection/Ceiling Front Projection/Ceiling Rear Projection.

Bluetooth Connection

Bluetooth Speaker

• If you want to connect to the projector via Bluetooth from your mobile phone, please select [Input Source] -> [Bluetooth Speaker] and follow the prompts.

Bluetooth Connection

• If you want to connect to a Bluetooth speaker/headphone at home, please select [Settings]->[More Settings]->[Bluetooth], and then select the device to be connected.

Wireless Connection

Screen Mirroring from Android Devices

• Please select [Smart Key] -> [Wireless Display], make sure your Android device and the projector are connected to the same Wi-Fi network, and follow the prompts to operate.

Stream Videos from DLNA

• Press the input source on the remote control, select [DLNA], make sure your phone/tablet and the projector are connected to the same Wi-Fi network, Open the video playback apps and follow the prompts to operate.

Screen Mirroring from iOS Devices

• Currently, due to iOS’s authorization restrictions, wireless screen mirroring cannot be achieved.
• Please use a lightning to HDMI adapter cable to achieve wired screen mirroring.

Wired Connections

Play from an HDMI Playback Device

This Apollo P50 supports connections with various HDMI playback devices, such as PC, DVD players, set-top box (STB), game console or other devices.

1. Connect this projector to an HDMI playback device with an HDMI cable.
2. Press the button on remote control to select [HDMI] and press .

Play from a USB Storage Device

With Apollo P50, you can enjoy music, video, and pictures, or install apps that are stored on a USB storage device.

1. Plug in the USB storage device.
2. Press the button on remote control to select [USB] and press .
3. Select a file you plan to play from the file and folder menu.
4. Press to start playback.

Play Through External Sound Devices Via AUX Cable

1. Connect one end of the 3.5mm AUX cable to the AUX port on this projector.
2. Connect the other end of the 3.5mm AUX cable to the AUX port on headphones or external speakers.
3. Playback on the projector.

Specifications

• Native Resolution: 1920×1080
• Speaker Drivers: 10W×2
• Throw Ratio: 1.4:1
• Aspect Ratio: 16:9/4:3
• Recommended Screen Size: 80″-120″
• Power Consumption: 110W
• Power Input: 100-240V AC, 50-60Hz 2.5A

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

ISED WARNINGS
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator&your body

WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital devices, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Suppose this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. In that case, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Declaration of Conformity

• We (The manufacturer is responsible for this declaration) Dynanic (Shenzhen) Technology Limited20th Floor, Building 4,
• Tianan Cloud Park, Bantian St., Longgang District, Shenzhen, China
• Declare under our sole responsibility that the product
• Trade name: ULTIMA
• Equipment: Projector
• Model No.: U0330

Which this declaration conforms with the essential requirement set out in the Council Directive on the Approximation of the laws of the Member States relating to the LVD Directive (2014/53/EU)&Rohs (2011/65/EU) product is responsible for affixing CE marking, the following standards were applied:

• EN IEC 62311:2020
• ETSI EN 301 489-1
• V2.2.3(2019-11)ETSI EN 301 489-17
• V3.2.4(2020-09)EN 55032:2015
• EN 55035:2017
• EN 61000-3-2:2019
• EN 61000-3-3:2013+A1:2019
• IEC 62321-3-1:2013
• IEC 62321-5:2013
• IEC 62321-4:2013+AMD1:2017
• IEC 62321-6:2015
• IEC 62321-7-2:2017
• IEC 62321-6:2015
• IEC 62321-8:2017
• Signature:
  • Date: 2023.09.01

CONTACT

• Apollo P50 Smart Projector
• MODEL NO: U0330
• Dynanic GmbH
• Buchenring 57, 22359 Hamburg, Germany
• UK Crossborder limited
• 7 Bell Yard London WC2A 2JR, UK United Kingdom
• Made in China
• Manufacturer: Dynanic (Shenzhen) Technology Limited
• Address: 20th Floor, Building 4, Tianan Cloud Park, Bantian St.,
• Longgang District, Shenzhen, China 518000

If you need our support, kindly reach out to our service team. We are always glad to help.

• +1 888-598-8875 (US)
• Mon-Fri 9am-5pm (PST)
• +49 89-628-25828 (EU)
• Mon-Fri 9am-5pm (CET)
• support@ultimea.com.
• support@ultimea.de.
• support.ultimea.com.
• support.ultimea.de.
• @ultimea_official
• SMART AS YOUR CHOICE
• Model No.: U0330
• Apollo P50
• Prefer video tutorials? Set up guidance videos and User Manuals on the ULTIMEA website.
• support.ultimea.com.
• @ultimea_official
• +1 888-598-8875 (US) Mon-Fri 9 am-5 pm (PST)
• +49 89-628-25828 (EU) Mon-Fri 9am-5pm (CET)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>