sytech SY-HC70R Rechargeable Hair Clipper User Manual

sytech SY-HC70R Rechargeable Hair Clipper

Product Information

Rechargeable Hair Clipper SY-HC70R

• Has a built-in rechargeable battery
• Comes with attachment combs and accessories
• Designed for indoor use only
• Blades should be oiled every few haircuts for maintenance
• Manufacturer reserves the right to make minor changes to the product design without prior notice

Product Usage

To use the Hair Clipper SY-HC70R, follow these instructions:

1. Ensure that the clipper is fully charged before use
2. Attach your desired attachment comb to the clipper
3. Turn on the clipper and begin cutting from the back of the neck upwards to the top of the ears
4. To cut the top of the head, lift the hair with your fingers or the comb and cut to the desired length. Always work from the back of the head, and gradually reduce the space between the comb/fingers and the head for shorter cuts. Comb out trimmed hair and check for uneven strands.
5. If you want to achieve a flat top or short cut, follow the four basic areas illustrated on the hair cutting guide in the manual.
6. To maintain your clipper, oil the blades every few haircuts. Do not use hair oil, grease, oil mixed with kerosene or any solvent as they may slow down the blades’ motion.
7. Clean the trimmer after each use and store it in a safe place for future use.

Safety Instructions

When using electrical appliances, including the Hair Clipper SY-HC70R, always follow these basic safety precautions:

• Do not throw the unit into fire, apply heat or leave it unattended near extreme temperatures
• Keep out of reach of children
• Read and follow all instructions and warnings in the manual

For any minor changes made to the product design, please refer to the updated manual provided by the manufacturer.

For more information about the product, visit www.sytech.es.

WELCOME

Thank you for purchasing the new rechargeable Hair Clipper SY-HC70R. In order to benefit fully from this product please read the following instructions carefully. Store the instructions manual in a safe place for future reference.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:

• Please read this instruction manual carefully before use and keep in a safe place for future reference.

• Before the first use of the appliance check that the voltage indicated on the rating label corresponds to the mains voltage in your home.

• For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than described in this instruction manual.

• In order to avoid possible risks and damages, it is advisable not to use the product for more than 30 minutes. After use, it is advisable to allow the appliance to cool down for a few minutes before using it again.

• Always keep the appliance and its accessories away from any heat sources.

• Do not use outdoors.

• Always unplug the product from the power supply before cleaning and when not in use.

• To prevent risk of electric shock and fire, do not immerse the appliance in water or any other liquids. However, if this does occur DO NOT TOUCH the appliance, unplug it immediately and contact your near service center.

• Do not use the product near water.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliances by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Do not leave the appliance switched on when not in use.

• Do not use other attachments than those supplied.

• Do not operate after malfunction or cord damage.

• Do not attempt to repair, adjust, or replace any parts of the appliance. Check and repair the malfunctioning by contacting Sytech Service Center.

• Keep the cord away from sharp edges and hot surfaces.

• Do not place or store the appliance where it can fall or be pulled into a tub or sink.

• Do not pull, twist, or wrap the power cord around the appliance.

• Never insert any objects into the openings of the appliance.

• Before use, make sure that blades are adjusted properly.

• Do not place the appliance while it is operating on any surface, it may cause injury or damage.

• Do not use the appliance with a damaged comb, or with teeth missing from the blades as injury may occur.
  NOTE: KEEP THE BLADES OILED

• Do not use the hair clipper when the skin is infected.

• Do not use the hair clipper on animals.
  The manufacturer reserves the right to introduce minor changes into the product design without prior notice, unless such changes significantly influence the product safety, performance, and functions.

IMPORTANT
This product has a built-in battery. Do not throw the unit into fire, apply heat, use, or leave the appliance unattended near extreme temperatures. This appliance is to be used only for indoor.
SAVE THESE INSTRUCTIONS

BEFORE YOU BEGIN

• Inspect the clipper making sure that it is free from hair and dirt.
• Check that the blades are lubricated.
• Check the clipper, making sure that there is no oil between the cutting blade teeth. Turn the unit on to distribute the oil and to make sure it is running smoothly before using. Wipe off any excess oil. This should be done before each use.
• Select the desired attachment comb (see below: parts and accessories) and fix it onto the clipper.
• It is advisable to begin with the highest setting and then reduce the setting until you reach the desired hair length.
• Seat the person so the head is approximately at the eye level. This allows ease of visibility while cutting and a better control of the clipper.
• Place a towel around the neck and shoulders of the person getting the haircut.
• Before cutting always comb the hair so it is tangle free.

REMINDERS

• Cut the hair in an even and slow manner. Use short strokes only and work gradually over the entire head.
• Always take off a little hair at a time; you can always trim off additional hair later.
• As you work, comb the hair frequently back into the style to which you are cutting.
• When cutting with this hair clipper it is better to leave the hair dry, not wet. With dry hair, it is much easier to control the amount of the hair being cut.
• Cutting hair requires practice so it is always better to leave the hair longer for the first few haircuts until you become used to the hair clipper levels and how much hair does each level cut

PARTS AND ACCESSORIES

Attachment Combs & Accessories

CHARGING THE HAIR CLIPPER

• The Xtrim clipper includes built-in rechargeable battery which makes it easier to move around while trimming your hair.
• You can either connect the cable to the charging base or directly to the hair clipper.
• Connect the supplied USB charging cable to the AC adaptor and the other end to the Hair clipper. Plug in the AC adaptor to the mains socket.
• IMPORTANT: DO NOT USE ANY OTHER ADAPTOR THAN THE SUPPLIED ONE.
• You can also connect the hair clipper directly to a USB port (5V-1A) without using the supplied AC adaptor.
• Once connected the charging indicator light will turn red and will turn to green once the charging process has finished.

Important:
DO NOT PLUG OR UNPLUG THE USB POWER CABLE WITH WET HANDS AS THIS CAN CUASE INJURIES AND RISK OF ELECTRIC SHOCK.

INSTRUCTIONS TO CUT YOUR HAIR

Attaching the Combs

• To attach the comb, hold it with its teeth upward and slide it along the sides of the hair clipper until the comb firmly adjusts onto the sides, and you hear the “click” sound.
• To remove the comb, simply pull the comb upward and away from the clipper.

CUTTING YOUR HAIR

STEP 1-BACK OF THE NECK

• Attach the 1/8” or 1/4” comb (attachment comb 1 or 2).
• Hold the clipper with the cutting edge pointed up and begin the haircut by starting at the center of the base of the neck.
• Hold the clipper comfortably in your hand and hold lightly against the head with the comb teeth pointing upward. Gradually and slowly lift the clipper, working upwards and outwards.
• As you cut, gradually lift the hair clipper head towards you. Continue to cut the back area from the bottom of the neck upwards to the top of the ears.

STEP 2-BACK OF THE HEAD

• Use the 3/8” or 1/2” attachment comb to cut the back of the head (attachment comb 3 or 4).

STEP 3- SIDE OF THE HEAD

• Change to one of the shorter combs (1/8” or 1/4”) to trim sideburns. Then change to one of the longer combs (3/8” or 1/2”) and continue to cut to the top of the head.

STEP 4- TOP OF THE HEAD

• Using the attachment comb 3/8” or 1/2” cut the hair at the top of the head from back to front against the direction in which the hair normally grows (See diagram 4). In some cases, this may require cutting from front to back.
• Attachment combs 3 mm or 6mm are used to achieve a close cut or short cut.
• For longer hair on top use the hair comb provided and lift the hair on the top of the head. Cut over the comb, with the hair lifted or hold the hair between the fingers to lift it and cut it to desired length. Always work from the back of the head. You can cut the hair shorter gradually by reducing the space between the comb/fingers and the head. Comb out trimmed hair and check for uneven stands.

STEP 5- THE FINISHING TOUCH

• Finally, use the cutter without an attachment comb for close trimming around the base of the neck, the sides of the neck and the ears.
• To produce a clean straight line at the sideburns, use the hair clipper with the top parts of the blades pointing straight to the hair.
• Press the clipper at right angles to the head, tips of the blades lightly touching the skin and work downwards. This way you will obtain a clean cut.

FLAT TOPS & SHORT CUTS 

• Starting with the longest attachment comb (1/2”) to cut from the back of the neck to the crown. Hold the attachment comb flat against the head and slowly move the clipper through the hair, as shown below.
• Use the same procedure from the lower side to the upper side of the head (as illustrated). Then cut the hair against the direction in which it grows and then level the cut from the sides.
• To give a ′flat top’ look; the hair on top of the head must be cut over the top of a flat comb rather than by using the attachment comb.
• Use closer cutting attachment combs to decrease the hair down to the neckline as desired. Comb hair and check for uneven areas.

OUTLINING

• Outlining requires no attachment combs.
• Take the clipper and push the level up to the close-cut position.
• Comb the hair and position the clipper between the sideburns and the ear (make sure the corner edge of the blade is against the hairline).
• Use the outline of the hair as your guide and slowly move the clipper over, around, and behind the ears.
• For the back of the neck and the sideburns, hold the clipper upside down to the level of hair you wish to cut, and move downwards. (Fig.5)

FLAT AND SHORT CUTS

• Always cut from the back of the neck to the crown using the longest attachment comb. Holding it flat against the head and slowly move the clipper up through the hair. Use the same technique for the sides, cutting from the bottom to the upper side of head. (See Fig.6)
• For the front of the crown, cut the hair against the direction in which it grows. Then even it up with the sides. (See Fig.7)
• For a flat top, use a flat comb, not the attachment comb. Use the comb to hold the hair up and then cut it. (See Fig.8)
• Lastly, to taper down to the neckline, use closer-cutting attachment combs. Comb the hair and check for uneven spots and make sure to outline sideburns and neckline following instructions under OUTLINING.

Four basic areas illustrated on the hair cutting guide:

MAINTENANCE

• Your clippers were carefully examined to ensure that the blades were oiled and aligned before leaving our factory.
• Blades must be realigned if they have been removed for cleaning or replacement.
• To realign the blades, simply match the upper and lower teeth blades together (the end of each of the top blade teeth should be approximately 1.2 mm back from the bottom blade teeth. Compare your clipper blades with the diagram shown).
• If the blade alignment is incorrect, add a few drops of oil to the blades, turn the clipper on for a few moments, then turn it off and unplug it.
• Loosen the screws slightly and then adjust. Tighten the screws after the blades are aligned.

OIL

• To maintain your clipper in great condition, the blades should be oiled every few haircuts.
• Do not use hair oil, grease, oil mixed with kerosene or any solvent. A solvent will evaporate and leave a thick oil, which may slow down the blades motion.

CLEANING THE TRIMMER

• Before cleaning, make sure to switch off the appliance and unplug it.
• Clean and oil the appliance after each use.
• Remove cut hair from the clipper with the brush enclosed.
• Wipe the clipper with a dry soft cloth.
• Oil the blades as mentioned above.
• Do not use any chemicals or abrasive liquids to clean this product.
• Never submerge the appliance into water as it will cause damage.

STORAGE

• Keep the appliance in a dry place.
• You may hang the cutter by the loop provided.
• The blades must be oiled during storage period.

SPECIFICATIONS

• Electric Hair Trimmer SY-HC70R
• 3 cutting length position
• 4 Attachment Combs to choose from
• Stainless steel blades
• Cord and cordless function
• Charging time: 1,5 – 2 hours
• Working time: 45 minutes
• Battery capacity: 500mAh
• Input: 5V-1A
• AC adaptor voltage: 100-240V – 50/60Hz
• Cable Length: 2 meters
• Accessories Supplied:
  • Oil Bottle
  • Scissors
  • Brush
  • Comb (x4)
  • Hair comb
  • USB charging cable
  • AC adaptor
  • Charging base
• Dimensions: 4,5x17x4 cm (Width/Height/Depth)
• Weight: 129 grams

DECLARATION OF CONFORMITY

Manufacturer Name: Satyatrade S. L.
Address: Pol. Ind. La Raya. C/ Guadalquivir, 2.
Camarma de Esteruelas, 28816 Madrid
Tel: 902 430 967
Fax: 91 8864285
NIF: B83254763
Manufacturing country: China
Description: Hair Clipper
Sytech® SY-HC70R complies with the following directives:
EMC Standard: Directive 2014/30/EU
LVD Standard: Directive 2014/35/EU
ROHS standard: 2011/65/EU Restriction of Hazardous Substance
Signed: Ajeet Nebhwani Utamchandani
Sole Administrator

www.sytech.es

References

• Sytech S.L.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>