Chicago Pneumatic CP872 Die Grinder User Manual
- June 15, 2024
- Chicago Pneumatic
Table of Contents
Operator’s Manual
CP872
Die Grinder
CP872 Die Grinder
WARNING
To reduce risk of injury, everyone using, installing, repairing, maintaining,
changing accessories on, or working near this tool must read and understand
these instructions, as well as separately provided safety instructions part
number 6159948750, before performing any such task.
Model| Speed| Power| Collet| Air consumption|
Weight| Dimension L| Air Inlet.| Inner hose
diameter| Sound Pressure| Sound Power| Vibrations
---|---|---|---|---|---|---|---|---|---|---|---
Free speed| at load| ahd| k
| __| __| __| __| | __| __| __|
__
[RPM]| [HP]
[W]
| [inch]
[mm]
| [SCFM]
[NI/min]
| [lb.] [kg]| [in.] [mm]| [in.]| [in.] [mm]| [dB(A)]|
[dB(A)]| [m/s 2 ]| [m/s 2 ]
1| 2| 3| 4| 5| 6| 7| 8| 9|
10| 11| 12
CP872| 27,000| 0.6
470| 1/4”
6.35| 0.236’’
6| 34
16.2| 20
9.6| 1.3
0.6| 6.6
167| 1/4”| 3/8”
10| 98.5| 109.5| 2.6| 0.68
Technical Data
Model| Speed| Power| Collet| Air consumption|
Weight| Dimension L| Air Inlet.| Inner hose
diameter| Sound Pressure| Sound Power| Vibrations
---|---|---|---|---|---|---|---|---|---|---|---
Free speed| at load| ahd| k
| __| __| __| __| | __| __| __|
__
[RPM]| [HP] [W]| [inch] [mm]| [l/min] [SCFM]| [kg] [lb]| [inch]
[mm]| [inch]| [mm] [inch]| [dB(A)]| [dB(A)]| [m/s2]| [m/s2]
1| 2| 3| 4| 5| 6| 7| 8| 9|
10| 11| 12
max. pressure 6.3bar(90psi)
ah : Vibration level, k Uncertainty ; LpA Sound pressure dB(A), KpA = KWA = 3
dB Uncertainty.
Declaration of noise and vibration statement (ISO 15744 and ISO 28927-12)
All values are current as of the date of this publication. For the latest
information please visit www.cp.com.
These declared values were obtained by laboratory type testing in accordance
with the stated standards and are suitable for comparison with the declared
values of other tools tested in accordance with the same standards. These
declared values are not adequate for use in risk assessments and values
measured in individual work places may be higher. The actual exposure values
and risk of harm experienced by an individual user are unique and depend upon
the way the user works, the workpiece and the workstation design, as well upon
the exposure time and the physical condition of the user. We, CHICAGO
PNEUMATIC TOOLS , cannot be held liable for the consequences of using the
declared values, instead of values reflecting the actual exposure, in an
individual risk assessment in a work place situation over which we have no
control. This tool may cause hand-arm vibration syndrome if its use is not
adequately managed.
An EU guide to managing hand-arm vibration can be found at
www.pneurop.eu/uploads/documents/pdf/PN3-02-NV_Declaration_info_sheet_0111.pdf.
We recommend a programme of health surveillance to detect early symptoms which
may relate to noise or vibration exposure, so that management procedures can
be modified to help prevent future impairment.
Machine type(s)
- This product is designed for removing material using abrasives. No other use permitted. For professional use only.
- Please read the instructions carefully before starting the machine.
Operation
- Fix the accessories properly to the tool.
- Connect device as shown in Fig. 01.
- To start the machine, pull the trigger (A). Machine speed is increase by increasing pressure on the trigger. Release the trigger to stop.
Lubrication
- Use an air line lubricator with SAE #10 oil, adjusted to two drops per minute. If an air line lubricator cannot be used, add air motor oil to the inlet once a day.
Maintenance instruction
- Follow local country environmental regulations for safe handling and disposal of all components.
- Maintenance and repair work must be carried out by qualified personnel using only original spare parts. Contact the manufacturer or your nearest authorised dealer for advice on technical service or if you require spare parts.
- Always ensure that the machine is disconnected from energy source to avoid accidental operation.
- Disassemble and inspect the tool every three 3 months if the tool is used every day. Replace damaged or worn parts.
- High wear parts are underlined in the parts list.
- To keep downtime to a minimum, the following service kits are recommended :
Tune-up kit : see parts list
Disposal
- The disposal of this equipment must follow the legislation of the respective country.
- All damaged, badly worn or improperly functioning devices MUST BE TAKEN OUT OF OPERATION.
- Repair only by technical maintenance staff.
EU Declaration of Conformity
We : CHICAGO PNEUMATIC Tool Co. LLC 1800 Overview Drive Rock Hill, SC 29730 –
USA
Machine type(s): Die grinder
Declare under our sole responsibility that the product(s): CP872 Serial
Number: 00001 – 99999
Origin of the product : TAIWAN
is in conformity with the requirements of the council Directives on the
approximation of the laws of the Member States relating : to “Machinery“
2006/42/EC (17/05/2006)
applicable harmonised standard(s) : EN ISO 11148-9:2012
Name and position of issuer : Pascal Roussy (R&D Manager) Place & Date :
Saint-Herblain,03/10/2016
Technical file available from EU headquarter. Pascal Roussy R&D manager CP
Technocenter 38, rue Bobby Sands – BP10273 44800 Saint Herblain – France
Copyright 2016, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part
thereof is prohibited. This applies in particular to trademarks, model
denominations, part numbers and drawings. Use only authorized parts. Any
damage or malfunction caused by the use of unauthorized parts is not covered
by Warranty or Product Liability.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>