Chicago Pneumatic CP3550 Series Angle Sanders User Manual
- June 7, 2024
- Chicago Pneumatic
Table of Contents
Chicago Pneumatic CP3550 Series Angle
_ **Sanders User Manual**_
Air Diagram:
Technical Data
max. pressure 6.3bar(90psi)
ah : Vibration level, k Uncertainty ; LpA Sound pressure dB(A), KpA = KWA = 3
dB Uncertainty.
Declaration of noise and vibration statement (ISO 15744 and ISO 28927-3)
All values are current as of the date of this publication. For the latest
information please visit www.cp.com. These declared
values were obtained by laboratory type testing in accordance with the stated
standards and are suitable for comparison with the declared values of other
tools tested in accordance with the same standards. These declared values are
not adequate for use in risk assessments and values measured in individual
work places may be higher. The actual exposure values and risk of harm
experienced by an individual user are unique and depend upon the way the user
works, the workpiece and the workstation design, as well upon the exposure
time and the physical condition of the user. We, CHICAGO PNEUMATIC TOOLS ,
cannot be held liable for the consequences of using the declared values,
instead of values reflecting the actual exposure, in an individual risk
assessment in a work place situation over which we have no control. This tool
may cause hand-arm vibration syndrome if its use is not adequately managed. An
EU guide to managing hand-arm vibration can be found at www.
pneurop.eu/uploads/documents/pdf/PN3-02-NV_Declaration_info_sheet_0111.pdf. We
recommend a programme of health surveillance to detect early symptoms which
may relate to noise or vibration exposure, so that management procedures can
be modified to help prevent future impairment.
Machine type(s)
- This product is designed for removing material using abrasives. No other use permitted. For professional use only.
- Please read the instructions carefully before starting the machine.
Operation
- Fix the accessories properly to the tool.
- Connect device as shown in Fig. 01.
- To start the machine, pull the trigger (A). Machine speed is increase by increasing pressure on the trigger. Release the trigger to stop.
Lubrication
- Use an air line lubricator with SAE #10 oil, adjusted to two drops per minute. If an air line lubricator cannot be used, add air motor oil to the inlet once a day.
Maintenance instruction
- Follow local country environmental regulations for safe handling and disposal of all components.
- Maintenance and repair work must be carried out by qualified personnel using only original spare parts. Contact the manufacturer or your nearest authorised dealer for advice on technical service or if you require spare parts.
- Always ensure that the machine is disconnected from energy source to avoid accidental operation.
- Disassemble and inspect the tool every three 3 months (500 hours) if the tool is used every day. Replace damaged or worn parts.
- To keep downtime to a minimum, the following service kits are recommended : Tune-up kit : see parts list
Disposal
- The disposal of this equipment must follow the legislation of the respective country.
- All damaged, badly worn or improperly functioning devices MUST BE TAKEN OUT OF OPERATION.
- Repair only by technical maintenance staff.
EU Declaration of Conformity
We : CHICAGO PNEUMATIC Tool Co. LLC 1815 Clubhouse road, Rock Hill, SC 29730
– USA
Machine type(s): Ange Sander
Declare under our sole responsibility that the product(s): CP3550-030AA,
CP3550-030AB, CP3550-120AA , CP3550-120AB, CP3550-085AA & CP3550-085AB
Serial Number: 00001 – 99999
Origin of the product : TAIWAN
is in conformity with the requirements of the council Directives on the
approximation of the laws of the Member States relating : to “Machinery”
2006/42/EC (17/05/2006)
applicable harmonised standard(s) : EN ISO 11148-8:2011
Name and position of issuer : Pascal Roussy (R &D Manager)
Place & Date : Saint-Herblain,25/04/2019 Technical file available from EU
headquarter. Pascal Roussy R&D manager CP Technocenter 38, rue Bobby Sands –
BP10273 44800 Saint Herblain – France
Copyright 2019, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part
thereof is prohibited. This applies in particular to trademarks, model
denominations, part numbers and drawings. Use only authorized parts. Any
damage or malfunction caused by the use of unauthorized parts is not covered
by Warranty or Product Liability.
NOTES : ____
NOTES: ____
NOTES: ____
EurAsian Conformity Mark.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>