Chicago Pneumatic CP7769 Impact Wrench User Manual
- June 4, 2024
- Chicago Pneumatic
Table of Contents
- Chicago Pneumatic CP7769 Impact Wrench User Manual
- WARNING
- Impact Wrench
- Technical data
- Declarations
- Noise and vibration
- Statement of use
- Product specific instructions
- Operation
- Clutch lubrication
- Lubrication
- Maintenance instructions
- Useful information
- Website
- Country of origin Taiwan
- Copyright
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Chicago Pneumatic CP7769 Impact Wrench User Manual
WARNING
To reduce risk of injury, everyone using, installing, repairing, maintaining,
changing accessories on, or working near this tool MUST
read and understand safety instructions (6159948710) before
performing any such task.
DO NOT DISCARD – GIVE TO USER
Impact Wrench
CP7769 | CP7769-6 | CP7779 | |
---|---|---|---|
Blows per minute | 1200 | 1200 | 1200 |
Free speed (rpm) | 6500 | 6500 | 6500 |
Max. torque (reverse) (Nm) | 1950 | 1950 | 1950 |
Max. torque (reverse) (ft.lb) | 1440 | 1440 | 1440 |
Max. working torque (Nm) | 1464 | 1464 | 1464 |
Max. working torque forward (ft.lb) | 1080 | 1080 | 1080 |
Min. working torque (Nm) | 407 | 407 | 407 |
Min. working torque forward (ft.lb) | 300 | 300 | 300 |
Square drive (“) | 3/4 | 3/4 | 1 |
Actual air consumption (l/s) | 19.3 | 18.6 | 19.1 |
Actual air consumption (cfm) | 40.7 | 39.2 | 40.3 |
Min. hose size (“) | 1/2 | 1/2 | 1/2 |
Min. hose size (mm) | 13 | 13 | 13 |
Air inlet thread size (“) | 3/8 | 3/8 | 3/8 |
Weight (kg) | 3.15 | 3.75 | 3.3 |
Weight (lb) | 6.9 | 8.3 | 7.2 |
Technical data
Declarations
Noise and vibration
These declared values were obtained by laboratory type test- ing in accordance with the stated standards and are suitable for comparison with the declared values of other tools tested in accordance with the same standards. These declared val- ues are not adequate for use in risk assessments and values measured in individual work places may be higher. The ac- tual exposure values and risk of harm experienced by an indi- vidual user are unique and depend upon the way the user works, the workpiece and the workstation design, as well upon the exposure time and the physical condition of the user.
We, CHICAGO PNEUMATIC Tool Co. LLC , cannot be held liable for the
consequences of using the declared values, instead of values reflecting the
actual exposure, in an individ- ual risk assessment in a work place situation
over which we have no control.
This tool may cause hand-arm vibration syndrome if its use is not adequately
managed. An EU guide to managing hand- arm vibration can be found by accessing
http://www.pneu- rop.eu/index.php
and selecting ‘Tools’ then ‘Legislation’.
We recommend a programme of health surveillance to detect early symptoms which
may relate to noise or vibration expo- sure, so that management procedures can
be modified to help prevent future impairment.
If this equipment is intended for fixtured applications: The noise emission is
given as a guide to the machine- builder. Noise and vibration emission data
for the com- plete machine should be given in the instruction manual for the
machine.
EU DECLARATION OF CONFORMITY
We, CHICAGO PNEUMATIC Tool Co. LLC , 1815 Club-
house Road, Rock Hill, SC 29730, declare under our sole re- sponsibility that
the product (with name, type and serial number, see front page) is in
conformity with the following Directive(s):
2006/42/EC (17/05/2006)
Statement of use
This product is designed for installing and removing threaded fasteners in
wood, metal or plastic.
No other use permitted. For professional use only.
WARNING Risk of injury
- If the torque is higher than 50 Nm, a reaction bar must be used.
The reaction bar is designed for absorbing the reac- tion torque of assembly power tools
Product specific instructions
Operation
See figures on page 2.
- Fix the accessories properly to the tool.
- Connect device to a clean and dry air supply.
- To start the machine, pull the trigger (A). Machine speed is increase by increasing pressure on the trigger. Release the trigger to stop.
- To switch rotation, push the switch (B). Use the reverse switch (B) only when the drive spindle comes to a com- plete stop. Changing the speed before the drive spindle stops may damage the machine.
- To adjust output power, turn the regulator (B).
Clutch lubrication
Use 0.5 oz. (14 g) of CP Pneu-Lube Synthetic Clutch grease.
Lubrication
Use an air line lubricator with SAE #10 oil, adjusted to two
- drops per minute. If an air line lubricator cannot be used, add air motor oil to the inlet once a day.
Maintenance instructions
• Follow local country environmental regulations for
safe handling and disposal of all components.
• Maintenance and repair work must be carried out by
qualified personnel using only original spare parts. Con-
tact the manufacturer or your nearest authorised dealer for advice on technical service or if you require spare parts.
- Always ensure that the machine is disconnected from en- ergy source to avoid accidental operation.
- Disassemble and inspect the tool every three 3 months if the tool is used every day. Replace damaged or worn
- To keep downtime to a minimum, the following service kit is recommended : Tune-up kit
Disposal
- The disposal of this equipment must follow the legisla- tion of the respective country.
- All damaged, badly worn or improperly functioning de- vices MUST BE TAKEN OUT OF OPERATION.
- The disposal of this equipment must follow the legisla- tion of the respective country.
- Repair only by technical maintenance
Useful information
Website
Log in to Chicago Pneumatic: www.cp.com.
You can find information concerning our products, acces- sories, spare parts and published matters on our website.
Country of origin Taiwan
Copyright
© Copyright 2018, CHICAGO PNEUMATIC Tool Co. LLC, 1815 Clubhouse Road, Rock Hill, SC 29730
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particu- lar to trademarks, model denominations, part numbers and drawings. Use only authorized parts. Any damage or mal- function caused by the use of unauthorised parts is not cov- ered by Warranty or Product Liability.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>