BRIZO 8SP-MU-5 Mystix Aromatherapy Essential Oil Pumping System Installation Guide

: June 15, 2024
: BRIZO

Table of Contents

BRIZO 8SP-MU-5 Mystix Aromatherapy Essential Oil Pumping System
Module Diagram
Installation
Assembly and Setup
Wiring Diagram
Warranty
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BRIZO 8SP-MU-5 Mystix Aromatherapy Essential Oil Pumping System

Read all instructions before installation

CAUTION

Failure to read these instructions before installation may result in personal injury, property damage, or product failure. The manufacturer assumes no responsibility for product failure due to improper installation.

NOTE: The Aromatherapy optional pump system is designed to work exclusively with the 8GE-TSG series generators and 8CH-600, 8CN-600 & 8CB- 600 series controls.

Module Diagram

Access screw to connect the control cable (centre top).
Peristaltic “Pump 1” (left).
Peristaltic “Pump 2” (right).
Manual forward and reverse switch for Pump 1.
Manual forward and reverse switch for Pump 2.
Peristaltic pump rollers.
Black peristaltic pump tube.
Clear Discharge tube (tube on the right side of each pump).
Clear Suction tube (tube on the left side of each pump into the canister.
Canister Caps drilled with 1/8’” holes.
Aromatherapy Canisters (purchased separately).
Bottle clips to secure essential oil canisters.
Tube Fitting.
Aromatherapy Adapter plugs ¾ NPT.
Aroma Injection Tee: ¾ copper X ¾ copper X ¾ NPT.

Installation

Select a location for mounting the Aromatherapy Module system in a utility area or closet near the steam room. The oil is injected directly into the steam line with an Aroma Injection Tee (15) going to the steam head. The distance from each pump to the tee should not exceed SIX FEET. This tee and the clear discharge tube (8) that carries the oil to the tee (15) must not be installed inside walls. This tubing and tee must be completely accessible for proper setup. Do not install any part of this assembly on a wall. The location may be above or below the steam line connection. The location should be convenient for replacing the oil canisters
Make sure a 120-volt outlet is located next to the Aromatherapy Module mounting location.
Secure two screws in the wall to hang the Aromatherapy Module in this location. The screws should be placed 5” apart and level.
Route the control cable from the Aromatherapy Module location to the 8GE-TSG series generator (or optional Chromatherapy, Audiotherapy and SensoriPLus). The manners in which the cables are routed are dependent on what is best suited for the installation. Three are four connection jacks in 8GE-TSG series generator(s) and two in the Aromatherapy, Chromatherapy, Audiotherapy and SensoriPLus allowing for tangible connections in the most convenient arrangement. How each product is interconnected is not important only that each product is interconnected.
Choose a location for the tee. The location is preferable to be level with or above the steam head. DO NOT install the tee below the steam head. This will provide a better aroma flow to the steam room and prevent the backflow of oil to the generator. When the steam generator outlet is located below the Steam head make a minimum of a 1” riser in the steam line located between the steam generator and the aroma injection tee. This will prevent the aroma oil from backing up into the generator. The location of the tee must remain accessible after the installation is complete. The injection tee is not intended to be buried in the wall. Make sure the plastic fittings are removed before putting the tee in place. Sweat the tee into the steam line in the horizontal position (shown in Figure 2). Do not install in any other position.
Plug the power cord (supplied) into the Aromatherapy Module’s circuit board (shown in Figure 4) and into an outlet. Make sure the pump rollers (6) spin when the switches are pressed on the Aromatherapy Module. If the pump does not spin check that the power supply is securely plugged into the pump control circuit board located behind the pump panel.

WARNING

Aromatherapy oils should not be ingested; even ingesting a small amount can cause poisoning. Aromatherapy oils should also not be applied to the skin and should be kept out of reach of children and pets. Aromatherapy oils are not a cure for medical conditions and should not be used to treat medical conditions. Elderly and pregnant individuals and those with a pre-existing medical condition should not use this device without consulting a physician in advance. Do not use the steam bath while under the influence of alcohol or drugs.

Assembly and Setup

The black peristaltic tube (5) needs to be installed into the pumps (see Figure 6).
- Remove (unsnap) the blue plastic cover (1) exposing the pump roller assembly.
- Pull out the Rotor (3) about a ¼”
- Place the tube between the pump base (4) and each of the rollers (2) forming a loop where the tube (7) follows the inside upper curve of the pump base.
- Push the lower right and lower left ends of the black tubing into the blue pump base securing it in the provided groves.
- Replace the blue cover on the pump base. Verify that the pump cover is fully seated to the base, so there is no space and the pump cover is not crushing the tube.
- Repeat the above procedure for the second pump.
Clear Tubing connections: The clear tubing that is used to carry the oil to the steam line is secured with special 1/8” tubing fittings (8). These fittings are assembled by sliding the tube through the nut (6) and bottoming the tube into the fitting. Then tighten the nut until the tube is secured (see Figure 7).
- With the bottles removed the clear suction tubes (7) should extend from the left side of the pump to the bottom of the cabinet. This will ensure that when the bottles are in place the tube extends to the bottom of the bottle. Connect the clear tube to the black peristaltic tube on the left (inlet) side of each pump.
- Connect the outlet side of each pump (right side) to a length of clear tube (7) that will be long enough to reach the tee connected to the steam line.
- Route the tube through the hole in the front pump panel and out the hole in the right side of the cabinet to the tee.
- Connect the tube for each pump to the fittings on the tee adapter. (See Figure 2).

Wiring Diagram

Warranty

Limited Warranty on Brizo® Steam Bath and Steam Shower Products

Residential Steam Bath Generators: Brizo Kitchen and Bath Company (“Brizo”) warrants to the original consumer purchaser that the parts (except for electronic parts) of its residential steam bath generator purchased from authorized Brizo sellers will be free from defects in materials and workmanship for as long as the original consumer purchaser owns the home in which the steam bath was originally installed. This lifetime limited warranty does not apply to residential steam bath generators that are used in commercial applications (as defined herein).
Residential Electronic Parts, Controls, Spa Options and Accessories: Brizo warrants to the original consumer purchaser that the electronic parts of its steam bath generator and its controls, spa options and accessories purchased from authorized Brizo sellers will be free from defects in materials and workmanship for two (2) years from the date that the product is received by the original consumer purchaser or their authorized representative (installation contractor, etc.). This two-year limited warranty does not apply to controls, spa options, electronic parts and accessories that are used in commercial applications (as defined herein).
Residential Shower Valve Model R80000E: DFC warrants to the original consumer purchaser that its residential shower valve model R80000E (except for electronic parts) purchased from an authorized Brizo seller will be free from defects in materials and workmanship for five (5) years from the date of purchase.
Commercial Warranty: For this warranty the term “commercial application” refers to installation in any setting in which the product is not being used for personal household use, including, but not limited to, hospitality applications, day spas and short-term and long-term rentals. Brizo warrants that the parts (including electronic parts) of its steam bath generators (including steam bath generators with model numbers beginning with 8GE that are 7.5kW-15kW), equipment, controls, electronic parts, spa options and accessories purchased from authorized Brizo sellers and used in a commercial application will be free from defects in materials and workmanship for one (1) year from the date that the product is received by the original purchaser or their authorized representative (installation contractor, etc.).
What We Will Do: Brizo will, at its option, repair or replace, free of charge, any part that proves defective in material and/or workmanship under normal installation, use and service during the applicable warranty period as stated above. Brizo may elect to refund the purchase price. Replacement parts are subject to availability and may differ from those originally supplied. For residential applications, two (2) years following the date that the product was received by the original consumer purchaser or their authorized representative (installation contractor, etc.), or for five (5) years for the residential shower valve model R80000E, and with prior approval by Brizo, Brizo will pay for labor for repair/replacement associated with warranty coverage. Thereafter, Brizo will not pay for labor associated with the removal/repair/replacement of products covered by this warranty. For commercial applications, Brizo will, with prior approval by Brizo, pay for labor associated with warranty coverage for ninety (90) days from the date that the product is received by the original purchaser or their authorized representative (installation contractor, etc.). Thereafter, Brizo will not pay for the labour associated with the removal/repair/replacement of products covered by this warranty. These are the consumer’s exclusive remedies.
What Is Not Covered: Because Brizo is unable to control the quality of Brizo products sold by unauthorized sellers unless otherwise prohibited by law, this warranty does not cover Brizo products purchased from unauthorized sellers.

This warranty does not cover damage caused by improper or negligent installation or use. Provided that Brizo is paying the cost of the labour under the terms above, this warranty does not cover repairs attempted by any person other than an authorized Brizo agent and shall be limited to the repair or replacement of defective parts by Brizo or its authorized agent.

This warranty is void if any of the following should occur

The use of the product for an unintended application, including a commercial application for all products except those products for which a commercial application is appropriate.
Failure to follow instructions, including care, cleaning and usage instructions, provided in the product’s owner’s manual.
The product’s serial number has been altered or removed.
The product is modified in any manner that Brizo concludes, after its inspection, affects the reliability of the product.
The product has been improperly repaired by anyone not specifically designated or authorized by Brizo.
The product is damaged because it is not operated or installed under undersupplied instructions.
The product is installed outdoors.
The product is installed in a moist and/or humid area with unconditioned air or temperatures that exceed 104 degrees Fahrenheit.
The product is damaged due to freezing.
The product is damaged by acts of God.

How to Make a Warranty Claim: To obtain warranty repair or replacement, contact Brizo at 800-355-6478 or steamprodserv@brizo.com to receive an RGA# (Return Goods Authorization number) which must be on the carton that is returned via UPS Ground or equivalent. Proof of purchase (original sales receipt showing purchase date) identifying the model and serial number and documentation of the date of receipt of the product by the original purchaser or an authorized representative (installation contractor, etc.) must accompany all warranty claims.
Limitation on Duration of Implied Warranties: Please note that some states/provinces (including Quebec) do not allow limitations on how long an implied warranty lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.
Limitation of Special, Incidental or Consequential Damages: Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of special, incidental or consequential damages, so the below
limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND BRIZO SHALL NOT BE LIABLE FOR, ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE.
Additional Rights: This warranty gives you specific legal rights, and you may also have other rights that vary from state/province to state/province. This is Brizo’s exclusive written warranty and the warranty is not transferable.