ET2 E22772-91PCFizz IV Flush Mount Ceiling Light Instruction Manual
- June 15, 2024
- ET2
Table of Contents
ET2 E22772-91PCFizz IV Flush Mount Ceiling Light
Product Information
Specifications
- Model number: ‘/(‘/2:92/7$*(,16758&7,216
- Power: Z’^ & Z Z Z
- Weight: Z ZZZ ZZ
- Dimensions: >Z Z
- Colour: >ZZZZZ ZZZ ZZZ
- Material: ZZZ ZZ
- Warranty: >Z ZZ
Product Usage Instructions
Step 1: Unboxing
- Open the packaging box carefully.
- Remove all the contents from the box.
Step 2: Power Connection
- Connect the power cable to the designated power outlet.
- Make sure the power source matches the required voltage mentioned in the user manual.
Step 3: Initial Setup
- Read the user manual thoroughly before proceeding.
- Follow the instructions provided to assemble any required parts.
- Connect any necessary accessories or peripherals.
Step 4: Product Configuration
Follow these steps to configure the product:
- Power on the product using the power button.
- Access the settings menu and adjust the desired configurations.
- Save the changes and exit the settings menu.
Step 5: Product Operation
Once the product is configured, follow these steps for operation:
- Refer to the user manual for specific instructions on product operation.
- Use the provided controls or interface to navigate and interact with the product.
- Follow any safety guidelines mentioned in the user manual.
FAQ
- Q: How do I clean the product?
- A: To clean the product, use a soft cloth dampened with mild detergent. Do not use abrasive cleaners or solvents.
- Q: What should I do if the product malfunctions?
- A: If you experience any issues or malfunctions with the product, refer to the troubleshooting section of the user manual. If the problem persists, contact our customer support for assistance.
- Q: Can I use the product outdoors?
- A: The product is designed for indoor use only. Using it outdoors may damage the product and void the warranty.
Before Getting Started
- Read the instructions carefully before assembling the product.
- When you open the package with a sharp tool like a box knife, be careful not to damage the components inside.
- Carefully remove all packaging materials and retain them for future use.
- Keep all hardware parts and packaging out of reach or small children.
- Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product.
- Ensure that you have all the required contents for complete assembly.
- Take care when lifting. Assemble the product close to where you intend to install it.
- Do not over-tighten the screws and bolts as this may damage the threads.
- Do not let children play with this product.
Risk of suffocation!
- Keep packaging materials away from children.
Lamp Care Instructions
- Carefully read through the instruction sheet before assembly and using the product.
- Caution there is a risk of shock!
- Disconnect from the power source before assembling or cleaning.
- Switch off, unplug and allow the bulb to cool before replacing the bulb or cleaning.
- Only use the recommended bulb type and do not exceed the maximum wattage as it could cause fire.
- Check the product cord to be sure is free torn or frayed.
- WARNING: Wires must be connected to a low-voltage driver and should not be connected directly to live wire or a short may occur.
Cleaning & Maintenance
- On polished finishes, often using talc powder can reduce the appearance of fingerprints and other smudges.
- For respective shade surfaces, use the appropriate cleansers, i.e. glass cleaner, stone polish, & wood polish.
- Clean with a soft cloth and a mild detergent. Do not use abrasive or harsh cleaners.
- Periodically (every 90-180 days) make sure that the screws are fully tightened.
- Prolonged exposure to heat sources may cause glazing, melting and scorching, or even cause colour to fade.
PARTS
Before getting, started, ensure the package contains the following components:
Installation Instructions
This fixture is equipped with an LED driver, please refer to the Wiring Diagram for more details.
WIRING DIAGRAM
ITEM/MODEL: E22772
- MUST be installed by an experienced professional CRITICAL KNOWLEDGE of electronic lighting systems is required.
- IMPROPER WIRING and/or INCORRECT DIMMER use can cause CATASTROPHIC DAMAGEI
- THIS FIXTURE MUST BE INSTALLED with a COMPATIBLE DIMMER SWITCH
- DO NOT CUT FACTORY-MADE CONNECTIONS.
FACTORY CONNECTIONS
- (+)INNER CONDUCTOR | OUTER MESHI(-)
VERIFIED LIST OF TESTED DRIVERS
- Lutron DVCL-153P
- Lutron DVCL-150P
- Leviton IPL06
- Leviton 6674
Due to the Inrush current, wattage should not exceed 150W on a 600W dimmer.
GENERAL COMPATIBILITY
- TRIAC / FORWARD PHASE ELV /
- REVERSE PHASE
- LOW VOLTAGE
IMPORTANT
- If the control is not paired properly with LED fixtures, irreparable damage may occur.
- If the dimmer you are using is not listed here, consult a lighting professional or view our dimming Compatibility Chart online: www.at2online.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>