BRIZO 110298 Kitchen Bridge Faucet With Spray Installation Guide
- June 15, 2024
- BRIZO
Table of Contents
110298 Kitchen Bridge Faucet With Spray
Installation Guide
110298 Kitchen Bridge Faucet With Spray
Model Number: ____
To find model number, look on the water line label underneath sink.
Date of Purchase: ____
Register Online
www.brizo.com/customer-support/product-registration
To reference replacement parts and access additional technical documents and
product info, visit www.brizo.com
1-877-345-BRIZO (2749)
www.brizo.com/customer-support
Read all instructions prior to installation.
CAUTION
Failure to read these instructions prior to installation may result in
personal injury, property damage, or product failure. Manufacturer assumes no
responsibility for product failure due to improper installation.
KITCHEN BRIDGE FAUCET WITH SPRAY
Image is for reference only.
You may need:
Insert body assembly through selected hole in sink. Secure assembly with
bracket and nut. Use supplied wrench to tighten nut.
DECORATIVE HOLE COVER INSTALLATION
Install mounting bracket and nut onto the mounting shank using wrench.
Slide “tee” hose harness (1) into top of diverter (2) and
secure with clip (3). Pull moderately on tube to ensure connection has been
made.
Insert ends of pex hoses (4)
into ends of “tee” hose harness (1). Attach clips (5) over hoses. Pull hoses
moderately to ensure connection is secure.
Insert spray trim into far right hole in sink. HAND TIGHTEN nut
below deck.
Insert sprayer hose through trim.
Pull diverter clip outward until loose, but do not completely
remove. Remove plug and discard if installing a side spray. Keeping the
diverter clip pulled out, insert spray hose into hose assembly.
Connect faucet supply lines to hot and cold water supplies.
A. Standard Connections
NOTICE
To avoid risk of property damage, Follow instructions for proper installation.
Failure to follow these instructions may result in risk of property damage
caused by leaking at this connection. Do not use pipe dope or other sealants
on water line connections.
Ensure all fittings and end connections are free of debris. Faucet fittings
(1) are 3/8″ compression. Loop tubing (2) if it is too long. Note:
Recommended tubing minimum bend diameter is 8″. Secure metal nut (3) to supply
valve connection (4). Turn nut until it feels snug. Then tighten nut at least
2 more turns with a wrench. Repeat for other tube. Turn on water, examine for
leaks.
B. Custom Fit Connections
NOTICE
If you determine the PEX supply tubing for this faucet is too long and must be
shorter to create an acceptable installation, be sure to read the instructions
and plan ahead. When cutting the supply tubing the installer accepts the
responsibility to do so in a way that allows a leak-free joint to be created.
Delta is not responsible for tubing that is cut too short or cut in a way that
will not allow for a leak-free joint. DO NOT use a metal sleeve (ferrule) or
gasket (supplied with faucet) in place of the plastic sleeve (ferrule)
supplied, it may not create a leak-free joint. Do not use pipe dope or other
sealants on water line connections.
For custom fit installations, you must use plastic sleeves (ferrules) supplied
with model and nuts included on supply lines. Tube cut must be straight. See
plastic sleeve (ferrule) installation instructions found in and included in
this document for more information.
Slide nut (1) over plastic sleeve (ferrule) (3). Start nut by hand onto supply
valve connection (2) to prevent cross-threading. Turn nut until it feels snug.
Then tighten nut at least 2 more turns with a wrench. Repeat for other supply
line. Turn on water, examine for leaks.
Potential Problems and Remedies
- Tubing is not cut perpendicular to the axis of the tube: carefully make an additional cut, being careful not to cut the tube too short.
- Tubing is cut too short: buy a coupling union and a replacement supply line that mate together from a store. The coupling union end intended to connect to the faucet must mate to the standard 3/8″ connection nuts and plastic sleeves (ferrules) supplied with the faucet.
- The plastic sleeve (ferrule) or connection nut is lost: purchase a replacement nut and/or plastic sleeve (ferrule) that are designed to seal with PEX tubing.
Correct method
NOTICE
Failure to use plastic sleeve (ferrule) in the correct orientation will result
in
- Determine desired length of supply tube (1). Leave 1″ or 2″ of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free.
- Slide nut (2) and plastic sleeve (ferrule) (3) onto cut supply tube. Ensure plastic sleeve (ferrule) is oriented as shown.
- Insert supply tube into supply valve connection (4). Supply tube should touch bottom of hole inside supply valve.
- Slide plastic sleeve (ferrule) down supply tube until it contacts the supply valve connection.
- Slide nut over plastic sleeve (ferrule). Start nut by hand to prevent cross-threading. Turn nut until it feels snug. Then tighten nut at least 2 more turns with a wrench. Repeat for other supply line. Turn on water, examine for leaks. disconnection and possible water damage.
Incorrect Installation
Do not install sleeve upside down.| Ensure cut is straight.
Do not use gasket (1) supplied with PEX tubing or brass ferrule (2) supplied
with valve stops.| Ensure tube is fully inserted into stop before sliding
sleeve down to engage top of fitting.
Remove aerator (1) using wrench (2) and turn faucet handles all the way on.
Turn on hot and cold water supplies and flush water lines for one minute.
Important: This flushes away any debris that could cause damage to internal
parts. Reinstall aerator. Check all connections for leaks.
Notice
Property damage and water leak possible. Leaks and property damage may occur
from incorrect installation. Follow all installation instructions before
making final connections and turning on the supplies.
Cleaning and Care
Care should be given to the cleaning of this product. Although its finish is
extremely durable, it can be damaged by harsh abrasives or polish. To clean,
simply wipe gently with a damp cloth and blot dry with a soft towel.
Maintenance
SHUT OFF WATER SUPPLIES BEFORE SERVICING VALVE OR SPOUT ASSEMBLIES.
If faucet leaks from spout or around handle body, replace valve cartridge (1).
A. Pull handle (5) straight up to remove it. Remove screw (3).
B. Remove adapter (4).
C. Install new cartridge and assemble other parts in reverse order. Make sure
glide ring (2) installed under handle before tightening screw (3).
Note: Line up handles with valves in closed position before refitting
handles.
Limited Warranty on Brizo® Faucets
Parts and Finish. All parts (other than electronic parts, air switch power
modules, batteries, and parts not supplied by Brizo Kitchen and Bath Company)
and finishes of Brizo® faucets purchased from authorized Brizo sellers are
warranted to the original consumer purchaser to be free from defects in
material and workmanship for as long as the original consumer purchaser owns
the home in which the faucet was first installed. For commercial purchasers,
(a) the warranty period is ten (10) years for multi-family residential
applications and (b) five (5) years for all other commercial uses, in each
case from the date of purchase. For purposes of this warranty, the term
“multi-family residential application” refers to the purchase of the faucet
from an authorized Brizo seller by a purchaser who owns but does not live in
the residential dwelling in which the faucet is initially installed, such as
in a rented or leased single unit or multi-unit detached home (duplex or
townhome), or a condominium, apartment building or community living center.
The following installations are not considered multi-family residential
applications, are excluded from the 10-year warranty, and are subject to the
5-year warranty: industrial, institutional or other business premises, such as
a dormitory, hospitality premises (hotel, motel, or extended stay location),
airport, educational facility, long- or short-term healthcare facility
(hospital, rehabilitation center, nursing, assisted or staged-care living
unit), public space or common area.
Electronic Parts and Batteries (if applicable). Electronic parts (other than
air switch power modules and batteries), if any, in Brizo® faucets purchased
from authorized Brizo sellers are warranted to the original consumer purchaser
to be free from defects in material and workmanship for five (5) years from
the date of purchase or, for commercial users, for one (1) year from the date
of purchase. No warranty is provided on batteries.
Air Switch Power Module. The electronic power module of Brizo® air switches
purchased from authorized Brizo sellers is warranted to the original consumer
purchaser to be free from defects in material and workmanship for two (2)
years from the date of purchase or, for commercial users, for one (1) year
from the date of purchase.
What We Will Do. Brizo Kitchen & Bath Company will repair or replace, free of
charge, during the applicable warranty period (as described above), any part
or finish that proves defective in material and/or workmanship under normal
installation, use, and service. Brizo Kitchen & Bath Company may, in its sole
discretion, use new, refurbished or recertified parts or products for such
repair or replacement. If repair or replacement is not practical, Brizo
Kitchen & Bath Company may elect to refund the purchase price in exchange for
the return of the product. These are your exclusive remedies.
What Is Not Covered. Because Brizo Kitchen and Bath Company is unable to
control the quality of Brizo products sold by unauthorized sellers, unless
otherwise prohibited by law, this warranty does not cover Brizo products
purchased from unauthorized sellers (visit Brizo.com to
see a list of our Authorized Online Resellers).
Any labor charges incurred by the purchaser to repair, replace, install or
remove this product are not covered by this warranty. Brizo Kitchen & Bath
Company shall not be liable for any damage to the product resulting from
reasonable wear and tear, outdoor use, misuse (including use of the product
for an unintended application), freezing water, abuse, neglect, or improper or
incorrectly performed assembly, installation, maintenance or repair, including
failure to follow the applicable care and cleaning instructions. Customized
components purchased by the consumer or commercial user and installed into a
Brizo product, and any damage resulting from removal or improper installation
of such components, are not covered by this warranty.
Brizo Kitchen & Bath Company recommends using a professional plumber for all
installation and repair of faucets. We also recommend that you use only
genuine Brizo® replacement parts.
What You Must Do To Obtain Warranty Service or Replacement Parts. A warranty
claim may be made and replacement parts may be obtained by calling
1-877-345-BRIZO (2749) or by contacting us by mail or online as follows
(please include your model number and date of purchase):
In the United States and Mexico: Brizo Kitchen & Bath Company
55 E. 111th Street
Indianapolis, IN 46280
Attention: Warranty Service
https://www.brizo.com/customer-support/contact-us
In Canada:
Masco Canada Limited, Plumbing Group
Technical Service Centre
350 South Edgeware Road
St. Thomas, Ontario, Canada N5P 4L1
https://www.brizo.com/customer-support/contact-us
Proof of purchase (original sales receipt) from the original purchaser must be
made available to Brizo Kitchen & Bath Company for all warranty claims unless
the purchaser has registered the product with Brizo Kitchen & Bath Company.
This warranty applies only to Brizo® faucets installed in the United States
of America, Canada, and Mexico.
Limitation on Duration of Implied Warranties. Please note that some
states/provinces (including Quebec) do not allow limitations on how long an
implied warranty lasts, so the below limitations may not apply to you. TO THE
MAXIMUM EXTENT PERMITTED
BY APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE
STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.
Limitation of Special, Incidental or Consequential Damages. Please note that
some states/provinces (including Quebec) do not allow the exclusion or
limitation of special, incidental, or consequential damages, so the below
limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND BRIZO KITCHEN &
BATH COMPANY SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS
PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY,
BREACH OF CONTRACT, TORT, OR OTHERWISE. BRIZO KITCHEN & BATH COMPANY SHALL NOT
BE LIABLE FOR ANY DAMAGE TO THE FAUCET RESULTING FROM REASONABLE WEAR AND
TEAR, OUTDOOR USE, MISUSE (INCLUDING USE OF THE PRODUCT FOR AN UNINTENDED
APPLICATION, FREEZING WATER, ABUSE,NEGLECT OR IMPROPER OR INCORRECTLY
PERFORMED ASSEMBLY, INSTALLATION, MAINTENANCE OR REPAIR, INCLUDING FAILURE TO
FOLLOW THE APPLICABLE INSTALLATION, CARE AND CLEANING INSTRUCTIONS. Notice to
residents of the State of New Jersey: The provisions of this warranty,
including its limitations, are intended to apply to the fullest extent
permitted by the laws of the State of New Jersey.
Additional Rights.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state/province to state/province. This is Brizo
Kitchen & Bath Company’s exclusive written warranty, and the warranty is not
transferable.
If you have any questions or concerns regarding our warranty, please contact
us as provided above or visit our website at
www.brizo.com.
© 2022 Masco Corporation of Indiana
References
- Brizo.com
- brizo.com
- brizo.com/customer-support
- brizo.com/customer-support/product-registration
- brizo.com/customer-support/contact-us
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>