KICHLER 52589CPZ LED 14.25 inch Champange Bronze Semi Flush Mount Instruction Manual

KICHLER 52589CPZ LED 14.25 inch Champange Bronze Semi Flush Mount

Product Information

Specifications:

• Mounting Strap [A]
• Mounting Screw (Qty. 2) [B]
• Outlet Box (Not Supplied) [C]
• Strap Mounting Screw (Qty. 2) [D]
• Lock Washer (Qty. 2) [E]
• Knob (Qty. 2) [F]
• Canopy [G]
• Lens [H]
• Countersunk Screws [I]
• Main Body [J]
• Ring [K]
• Metal Tabs [L]

Product Usage Instructions

Securing the Lens:

1. Remove the main body from the ring[K] carefully.

Installation Instructions:

1. Find the appropriate threaded holes on the mounting strap[A] that align with the hole distance in the canopy[G]. Assemble mounting screws[B] into threaded holes starting from the outlet box side.
2. Attach the mounting strap to the outlet box[C] using the supplied strap mounting screws[D]. The mounting strap can be adjusted to suit the position of the fixture.
3. Connect the wires. Refer to the chart below for correct connections.

Wire Connections:

Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

Note: When parallel wire (SPT 1 & SPT 2) is used, the neutral wire is square- shaped or ridged, and the other wire will be round in shape or smooth (See illustration).

4. Raise the canopy to the ceiling, carefully passing the mountingscrews[B] through the mounting screw holes in the canopy. Make sure the wires do not get pinched between the mounting strap and canopy or canopy and ceiling.
5. While holding the canopy in place, use lock washers[E] andknobs[F] to secure the canopy[G]. Tighten to secure.

FIXTURE DIAGRAM

PARTS LIST

• [A] Mounting Strap
• [B] Mounting Screw (Qty. 2)
• [C] Outlet Box (Not Supplied)
• [D] Strap Mounting Screw (Qty. 2)
• [E] Lock Washer (Qty. 2)
• [F] Knob (Qty. 2)
• [G] Canopy
• [H] Lens
• [I] Countersunk Screws
• [J] Main Body
• [K] Ring
• [L] Metal Tabs

CAUTIONS

CAUTION RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING: This fixture is intended for installation by the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

• Always be certain that the electric current is turned off before cleaning.
• Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

SECURING THE LENS

NOTE : Lens[H] may become loose during shipping. To secure the lens in place (if needed), follow these steps before following the INSTALLATION INSTRUCTIONS.

1. Unscrew countersunk screws[I] from the top of the main body[J] (see Fig. 1).
2. Carefully remove the main body from the ring[K].
3. Carefully press any loose metal tabs[L] down against the top of the lens[H] to secure the lens in place.
4. Carefully lower the main body into the ring, align holes on top of the main body with the holes in the ring, and screw countersunk screws into the holes. Tighten to secure.

INSTALLATION INSTRUCTIONS

1. Find the appropriate threaded holes on the mounting strap[A] that align with the hole distance in the canopy[G]. Assemble mounting screws[B] into threaded holes starting from the outlet box side.
2. Attach the mounting strap to the outlet box[C] using the supplied strap mounting screws[D]. The mounting strap can be adjusted to suit the position of the fixture.
3. • On fixtures where the mounting strap is provided with a hole and two raised dimples, wrap ground wire from the outlet box around the green ground screw, and thread it into the hole.
   • On fixtures where a cupped washer is provided, attach the ground wire from the outlet box under the cupped washer and a green ground screw, and thread it into the mounting strap. Grounding instructions: (See Illus. a or b). If the fixture is provided with ground wire, connect the fixture ground wire to the outlet box ground wire with the wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
4. Make wire connections. Reference cthe hart below for correct connections and wire accordingly.
   Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
   ---|---
   Black| White
   Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
   Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

Note : When parallel wire (SPT 1 & SPT 2) is used, the neutral wire is square-shaped or ridged, and the other wire will be round in shape or smooth (See illustration).

5. Raise the canopy to ceiling, carefully passing mounting screws[B] through mounting screw holes in the canopy.
   NOTE : Be certain wires do not get pinched between the mounting strap and canopy or canopy and ceiling.

6. While holding the canopy in place, use lock washers[E] and knobs[F] to secure the canopy[G]. Tighten to secure.

FCC INFORMATION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

For warranty information please visit: kichler.com/warranty

FAQ’s

Where can I find warranty information for the product?
For warranty information, please visit kichler.com/warranty.

References

• Kichler® Warranty Information | Kichler Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>