KICHLER 52600CPZ LED Flush Mount Ceiling Light Installation Guide
- June 15, 2024
- KICHLER
Table of Contents
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
FIXTURE DIAGRAM
PARTS LIST
[A] Upper Frame
[B] Mounting Strap
[C] Lower Frame| [D] Strap Mounting Screw (Qty. 2)
[E] Countersunk Screw (Qty. 3)| [F] Outlet Box (not supplied)
[G] Studded Knob (Qty. 3)
---|---|---
CAUTIONS
CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fuse box before
starting and during the installation.
WARNING:
- This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.
CLEANING:
- Always be certain that electric current is turned off before cleaning.
- Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.
INSTALLATION INSTRUCTIONS
-
Carefully lower the upper frame [A] into lower frame [C], aligning (3) holes along inside edge of upper frame with (3) holes along top edge of lower frame.
-
Insert a studded knob[G] into each set of aligned holes and tighten to secure upper frame to lower frame.
-
Attach mounting strap [B] to outlet box [F] using strap mounting screws [D].
-
Grounding instructions: (See Illus. a or b).
a. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
-
Make wire connections. Reference chart below for correct connections and wire accordingly.
Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is
square shaped or ridged and the other wire will be round in shape or smooth
(See illus.) 
-
Raise fixture to ceiling, carefully passing upper frame [A] over mounting strap [B] , and aligning the (3) holes in side of upper frame with the (3) holes in side of mounting strap.
NOTE: Be certain wires do not get pinched between mounting strap and upper frame, or upper frame and ceiling. -
While holding upper frame in place, insert a countersunk screw [E] into each set of aligned holes and tighten to secure fixture to mounting strap.
FCC INFORMATION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For warranty information please visit: kichler.com/warranty
REV 10-SEP-2022
IS-52600-US
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>