SKYDANCE C4 Dimming 4 Channel LED RF Controller Instruction Manual
- June 4, 2024
- SKYDANCE
Table of Contents
SKYDANCE C4 Dimming 4 Channel LED RF Controller
Features
- Set as single color, dual color, RGB or RGBW controller by DIP switch.
- DC to DC constant current output, multiple output current settings.
- Match with RF 2.4G single zone or multiple zone single color, dual color and RGB/RGBW remote control.
- One RF controller accept up to 10 remote control.
- 4096 levels 0-100% dimming smoothly without any flash.
- When using with RGB/RGBW light, built in 10 dynamic mode, include jump or gradual change style.
- Auto-transmitting function: Controller automatically transmit signal to another controller with 30m control distance.
- Synchronize on multiple number of controllers.
- Fade in and out effect selectable.
- Connect with external push switch to achieve on/off and 0-100% dimming function.
Technical Parameters
Mechanical Structures and Installations
LED Current Selection
Note: Please select the correct current through the DIP switch on the PCB
board when the power is off. 
Wiring Diagram
Note:
- The LED quantity at each channel can be different, the controller could auto check and output a proper voltage to each channel according to its LED quantities.
- The controller works on buck mode, the voltage of power supply should be greater than the total voltage of the seried LEDs.
Push Dim
Color rotation:
We can select 4 rotation speed:
10 flash/s means 6 seconds color rotation, 5 flash/s means 30 seconds color
rotation, 2 flash/s means 1 minute color rotation, 1 flash/s means 6 minutes
color rotation.
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key
Match:
Short press match key, immediately press on/off key (single zone remote) or
zone key (multiple zone remote) on the remote.
The LED indicator fast flash a few times means match is successful.
Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast
flash a few times means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again. Immediately short
press on/off key (single zone remote) or zone key (multiple zone remote) 3
times on the remote. The light blinks 3 times means match is successful.
Delete:
.Switch off the power, then switch on power, repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 5 times on the remote. The light blinks 5 times means all matched
remotes were deleted.
RGB/RGBW dynamic mode list
| No. | Name | No. | Name |
|---|---|---|---|
| 1 | RGB jump | 6 | RGB fade in and out |
| 2 | RGB smooth | 7 | Red fade in and out |
| 3 | 6 color jump | 8 | Green fade in and out |
| 4 | 6 color smooth | 9 | Blue fade in and out |
| 5 | Yellow cyan purple smooth | 10 | White fade in and out |
Dual color control
CH1,CH3=Warm white LED
CH2,CH4=Cool white LED
Each channel can supply up to 10W(@350mA, 30V) and white balance can be
controlled as such:
| Color temperature | Cool white | Neutral white | Warm white |
|---|---|---|---|
| Power distribution | CH1=0W,CH2=10W | CH1=5W,CH2=5W | CH1=10W,CH2=0W |
| CH3=0W,CH4=10W | CH3=5W,CH4=5W | CH3=10W,CH4=0W |
Fade in and Fade out Setting
Long press match key 5s, then short press match key 3 times, The lighting
effect will be set to the fade in and fade out in 3s, the indicator light of
LED controller blinks 3 times. Long press match key 10s, restore factory
default parameter, the light on/off time restores to 0.5s.