Kogan KAMN34F1QULB Freesync Monitor User Guide

Kogan KAMN34F1QULB Freesync Monitor

Components

• Monitor
• Stand arm
• Base
• Headphone stand
• DP cable
• Stand screws (PM5*11 x4)
• VESA screws (M4*12 x4)
• CH-211 Power cable

Overview

The monitor comes with several buttons and indicators:

Signal.
Power button| Turn on/off the monitor.

Indicator:

signal or the monitor is in standby. Ensure your computer is turned
on and operates normally and check that all video cables are fully
plugged in and/or connected to the monitor.

SAFETY & WARNINGS

• Read all instructions before using the appliance and retain for reference.
• This monitor is designed with ventilation holes on the back of the casing. Do not cover or block them.
• Do not insert any object or spray any liquid into the vents.
• Avoid placing the monitor near heaters, stoves, fireplaces or other sources of heat, as well as in rooms lacking adequate ventilation.
• Do not position the monitor in unsafe locations. If the monitor falls, it may be damaged and may injure nearby people.
• Unplug the monitor if it is not going to be used for an extended period.
• Do not place heavy objects on the monitor, its power cord or any connected cable.
• Do not open the back panel of the monitor, as it contains a high-voltage current even when not plugged in.
• There is a polarizer layer (not a protective film) on the surface of the screen. Do not peel it off, or the product may be damaged and the warranty will be invalid.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

COMPONENTS

OVERVIEW

Indicator

ASSEMBLY

1. Open the carton, and remove the stand arm, base and headphone stand. Leave the monitor in foam.
   Secure the stand arm to the base using one of the screws. Attach the headphone stand to the stand arm.

2. Remove the bottom half of the protective foam from the monitor.
   Press the quick-release button and remove the stand plate then attach it to the stand assembly using two screws.
   Note: When handling the monitor, do not pinch the screen with your hand to avoid damaging the display.

3. Attach the stand plate and stand assembly back onto the rear of the monitor.
   Remove the remaining protective foam and stand the monitor upright.
   Note: To remove the stand from the monitor, slide the quick-release button up and pull the stand assembly outwards.

VESA MOUNT

VESA mounting pattern 75x 75mm, screw size M4.
Note: VESA mount or mounting accessories are not included.

1. Open the box, take out the monitor with protection foam attached and gently place it on a desktop or table. Ensure all components are removed from the foam covering. Press the quick release button to remove the stand plate.
   If the monitor is already attached to the stand, remove the stand before proceeding with VESA mount assembly.

2. Remove the four screws from the rear case. Do not remove the monitor from the foam at this stage.

3. Remove the four VESA screws from the accessory bag and attach them to the rear casing.

4. During the hanging of the product, do not pinch the screen with your hand to avoid damaging the screen.
   Instructions for attaching to the specific wall mount will be included with the mount.
   Notes: To prevent the monitor on the mount from failing, please install it firmly and protect it fully. Do not place or hang any object on the mount. Ensure the height of the mount is less than 2 meters.
   Notes: T o prevent the monitor on the mount from failing, please install it firmly and protect it fully. Do not place or hang any object on the mount. Ensure the height of the mount is less than 2 meters.

CONNECTIVITY

Power Cable
Connect the included power cable to the monitor power port and then connect the other end to a power outlet. Audio Out
Connect an audio output device (speakers, headphone etc.) to the 3.5mm audio port on the monitor.

HDMI
Connect an HDMI cable from the computer’s display output to the monitor’s display input.

DisplayPort
Use the supplied DP cable to connect the computer’s display output to the monitor’s display input.

OPERATION

1. Connect the monitor to your input device via HDMI or DP.
2. Connect the power cable to your monitor and then connect the other end directly to a power socket.
3. Use the power button to turn the monitor on.

Menu description

• The colour and shape of the OSD menu of the actual computer may be slightly different from those shown in the figure.
• Specifications of the OSD menu may change with improvements of functions without prior notice.

The screen display (OSD) menu can be used to adjust the settings of the monitor and is shown on the screen after the monitor is powered on and the button is pressed.

1. Press one of the butt Mons ( ) to activate the browser screen.
2. Press M to enter the OSD screen.
3. Press scroll through the functions.
4. Select the desired function, and press
5. Press scroll through the sub-menus, and press a key to select and confirm the desired function.
6. Press select one option, and press M to confirm settings and exit from the current menu.
7. Press   to exit from the menu screen

Functions of the monitor vary with models, and the functions in this manual are for reference only.

Functions of the monitor vary with models, and the functions in this manual are for reference only.

SPECIFICATIONS

Need more information?
We hope that this user guide has given you the assistance needed for a simple set-up.
For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

References

• Kogan Help Centre

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>