VSYSTO F9C 4 Inch IPS Screen WiFi Dash Cam User Manual

F9C Dash Cam
User Manual V1.2

Notes for Using the Dash Cam

• This product is an auxiliary (vehicle driving recorder) product for safe driving.
  Any loss caused by malfunction, information loss or using this product is irrelevant to our company.

• This product is an auxiliary device for recording external images of vehicles.
  Due to the different driving environment and vehicle environment, some functions will not support. The unscheduled firmware upgrade in order to improve the product will change the performance of the product, and sometimes the camera will cannot record due to the environment, so the driving images recorded in this product is for reference only. The state of TF card will also lead to camera cannot record.

• Although this product can record and save the videos of accidents, it does not guarantee that all the accident videos can be recorded. Slight collision accidents can’t start the collision sensor, so the video may not be recorded in the  specialized folder.

• Be sure to disconnect the power supply when inserting or pulling out TF memory card.

• For the stable use of the product, it is recommended to format the TF card at least once a week.

• Generally TF card has a service life.Long-term use of TF card may cause the data to be unable to save. In this case, it is recommended to buy a new TF card to use. Our company will not be liable for data destruction caused by the  long-term use of TF card.

• Please do not install or operate this product while driving.

• This device may disturb the function of improperly protected medical equipment.
  If you have any question or are uncertain whether the medical equipment can shield external RF energy, please consult your doctor or medical equipment manufacturer.

• Please do not make this product subject to strong impact or vibration, so as not to damage the product and cause malfunction or unavailable.

• Please do not use it in an environment with excessive dust density, so as to prevent cameras and other parts from being contaminated with dust, which will affect the video effect.

• Please stop using this product before cleaning and maintenance.

• Please do not use chemical solvents or detergents to clean this product.

• Please do not disassemble or modify this product without authorization.

• The ambient temperature range for the normal use of this device’s function is 20 to 65 degrees Celsius.
  Exceeding this temperature range may lead to product failure, fire or explosion.

• Please use it within the scope  permitted by law.

• Disclaimer: Tire pressure sensors may not fit all vehicle tires. Please consult your vehicle manual or a tire professional whether the tire pressure sensors are fit your car. If they affect your vehicle’s performance, driving, or insurance coverage, do not install it!

• The manufacturer and distributor will not be responsible for damage due to improper installation and usage.

Packing List

After opening the package, please confirm whether the driving recorder is in good condition and the accessories are complete.

1. Main Unitxl
2. Power Cable x1
3. Bracket x1
4. GPS Module x1
5. Camera x2
6. TPMS (Optional)x4
7. TF Card(Optional)x1
8. Wired Controller x1

“Optional” mean it is not a standard configuration. Please refer to the product description on the platform you purchased!

Product Appearance Diagram

Product Connection Diagram

▶ With the advancement of technology, the product structure and parameters will continue to be improved.
The pictures and texts in this book are for reference only. If there are pictures or descriptions that do not match the actual product, please refer to the actual display of the product.

Images Information and Menu Description

1. After selecting, press [OK] to enter Video Mode.
2. The icon becomes larger to indicate that the function is selected.
   

Character description on the display in video mode

1. After selecting, press[OK]to enter Playback Mode.

2. The icon becomes larger to indicate that the function is selected.

3. 

Press ▲▼ to select the video to playback

Long press for 3 seconds in the Playback Mode to switch to the video files list of front ant rear camera
Front camera video files name identification: RECThe year, month and time of current video F.MOV
Rear camera video files name identification: REC The year, month and time of current video R.MOV

min/3min
5.Parking monitoring| On/off
6.Parking monitoring sensitivity| Set the vibration sensitivity when parking
7.Recording Time After Flameout| Set recording time after flameout
8.Date format| 3 options, YYYY MM DD/MM DD YYYY/DD MM YYYY
9.Clock setting| Day&Time
10.Time zone selection| Time zone selection around the world
11.Date watermark| On/off
12.Speed watermark| Whether it is necessary to turn on/off the driving speed display when playing video on the computer
13.0verspeed alarm| Set the overspeed alarm value. When the driving speed exceeds the preset value, the recorder will issue an alarm prompt
14.GPS status| Display the current number of satellites, longitude, latitude and other information
15.Unit system| Set the speed unit selection displayed when driving
16.TPMS tire pairing| Whether the tire needs to be paired with tire pressure sensors
17.Tire pressure unit| 2 unit options, bar/psi
18.Tire pressure alarm sound| On/off
19.Tire pressure alarm threshold| Set the alarm sound for the lowest and highest values of tire
20.Rear camera mirror| Whether mirror selection is required for the rear camera display
21.Protect Level| G-Sensor sensitivity level adjustment
22.Button sound| On/off
23.Voice prompt| On/off
24.System reset| Restore to the factory default settings
25.WiFi mode| On/off
26.Format SD card| Delete all videos from the memory card
27.Operation guide| The operation guide of button function of wired controller
28.FW version| Information about the current software version of the recorder

1. After selecting, press[OK]to enter Language Choosing Mode.
2. The icon becomes larger to indicatethat the function is selected.

1. Language identification — Corresponding to the selected language
2. The number of language choices depends on the actual model!

W5T Wired Controller Operating Instructions

Recorder Video Playback Operation

In the video recording interface, long press the OK button once to switch to the setting interface. Use the up/down buttons to select the player icon. After selecting, short press the OK button once to enter the playback mode. Then select the video you want to play, and short press the OK button once to start the video. The default is the front camera video, long press the up button to switch to the rear camera video file.

ATTENTION
There is a temperature sensor inside the wire controller. If the wire controller is operated,it is normal to find that the temperature of the recorder rises.
The built-in temperature sensor has a deviation of 2 degrees Celsius.

Mobile Phone APP Installation and Operation

The APP is a mobile phone control software used with VSYSTO DVR device.This software is connected to the DVR device via Wi-Fi, it can directly preview and playback the video on the mobile phone,easily realize that viewing the camera documents on the screen of mobile phone,setting or other operations. Subverting the control method of traditional cameras,bring you a new experience.

App download for Android user

App download for Apple user

Scan the QR code above to download the latest APP from Google Play or APP Store. Or you can search “WiFi Camera”on Google Play or APP Store to download and install it.
Conditions of use and product association:

1. Smart terminal with Android 5.0 or higher or Apple terminal.
2. Purchase a recorder terminal device that uses VSYSTO design scheme, and connect the mobile phone WiFi to the camera correctly.

DVR WiFi Default Name: VSYSTO-F9C-XXXX Default password: 1234567890
Connection Steps: 0)Turn on the recorder;

1. Enter the WiFi setting interface of the phone, find the corresponding WiFi name, and enter the password to connect to WiFi;
2. Open mobile APP, connect the recorder.

*To ensure the normal use of APP functions, please update the APP to the latest version in time.

Installation Guide

Camera Bracket

During installation, it is recommended to install the extension cable first, and then connect the main unit and camera separately(so that the installation is easier). If the distance between the main unit and the camera is less than 0.5 meters, it is recommended not to use the camera extension cable (please keep the camera extension cable for future needs).

Power Cable

1. Black GND -Connect Ground(Ground refers to the negative pole of the iron sheet screw of the vehicle body.)
2. VCC – Connect Constant Power(Constant power refers to the fuse that has been powered on after the vehicle is turned off.)
3. ACC – Connect Key switch(ACC refers to the fuse that has power after starting the vehicle, but has no power after flameout.)
   ※Only the smart power cable supports the parking monitoring function. The car charger power cable does not support the parking monitoring function.

Auxiliary Display Mode

1. Long press the down button of the wire controller to enter the auxiliary display mode, and the driving speed is displayed on the first interface.

2. Short press the down button again to enter the tire pressure monitoring interface (optional)
   

3. Short press the down button again to enter the battery power display interface

4. Short press the down button again to enter the GPS information interface
   

5. Short press the down button again to enter the current mileage short-term memory interface

6. Short press the down button again to enter the year month and day interface

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>