VSYSTO S6 WiFi Motorcycle Dash Camera User Manual

VSYSTO S6 WiFi Motorcycle Dash Camera

Product Accessories

After opening the package, please confirm whether the driving recorder is in good condition and the accessories are complete.

1. Host x 1
2. Cameras x 2
3. Wired Remote Controller x 1
4. USB Test Cable x 1
5. Cable Ties x 8
6. GPS Module x 1(Optional)
7. Power Cable x 1
8. Bracket x 1
9. Memory Card x 1(Optional)
10. Signal Enhancer x 1
11. Wire Clips x 1 Set

Product Appearance Diagram

With the advancement of technology, the product structure and parameters will continue to be improved. The pictures and texts in this book are for reference only. If there are pictures or descriptions that do not match the actual product, please refer to the actual display of the product.

How to use

1. Quick Test and Installation
   Please refer to the “Quick Installation Guide”.

2. Insert the Memory Card
   Insert the memory card into the card slot until you hear “Da”. If you want to take out the card, gently press the memory card and slowly release it after hearing “Da”.

Tips

• Please insert the memory card in the correct direction.
• Please do not pull out or insert the card when it is turned on to avoid damaging the video file and recorder.
• Please use the high-speed Class10 or above genuine card.
• Please format the memory card regularly to keep it in good condition.

Video Recording

Normal Recording Mode

• After the motorcycle power is turned on, the recorder will automatically start recording, and the LED indicator on the remote controller will slowly flash. When the motorcycle power is off, the recorder will automatically stop recording(If there is no vibration for 5 minutes after the motorcycle flames out, the recorder will shut down).
• Loop Recording: The recorder will save a file after recording for a while (the default setting is 3 minutes). When the memory card is full, the system will delete the oldest file. You can manually set the time of video recording in APP. (1/2/3/5 minutes can be set, and front and rear lens files are saved in F and R folders respectively). The normal recorded video file is named “REC-xx”.

Emergency Recording Mode

• G-Sensor emergency recording mode: When the motorcycle collides with other vehicles or the vibration is strong, the built-in G-Sensor will automatically activate the emergency recording mode. The LED indicator on the remote controller flashes rapidly. The emergency video file is named “GSR-xx”. You can set the sensor sensitivity level in the menu or APP. The higher the sensitivity, the easier to trigger G-Sensor.
• Manual emergency recording mode: When the recorder is recording, short press any one button of the wired remote controller to lock the current recorded video, and the front and rear cameras will capture a photo at the same time. The manually locked video file is named “ KEYxxxx”.

Tips

• If the memory card is not inserted or is faulty, the video cannot be saved.
• KEY” and “GSR” emergency video files can be saved 10 each. After more than 10, the system will automatically delete the earliest one.

View Video

1. Connect the recorder via WiFi, and view the real-time and playback video on the mobile APP (Android& iOS).
2. View on Computer Put the memory card into the USB card reader, connect it to the available USB port on the computer, read the contents of the memory card, then select the video to play.

• Scan the QR code above to download the latest APP from
• Google Play and APP Store. Or you can search “WiFi
• Camera” on Google Play or APP Store to download and install it.
• DVR WiFi Default Name: MotoDV_XXX
• Default password: 1234567890

Connection Steps: ①Turn on the recorder;

• Enter the WiFi setting interface of the phone, find the corresponding WiFi name, and enter the password to connect to WiFi;
• Open the mobile APP, and connect the recorder.

Tips

• If “No network connection” is displayed when connecting to WiFi, please turn off the mobile data network first, and then connect to the recorder WiFi according to the steps. If the prompt “Current WLAN is unavailable, whether to switch to another network?” appears, you must click “No”.
• After entering the APP, the recorder will pause recording. Please click the red recording button on the APP to start recording. After exiting the APP, the recorder will start recording in 30 seconds.
• You don’t need to connect to WiFi for daily riding. Connect when you need to watch the video.
• In case of connection failure, please contact customer service.

Wired Remote Controller Operating Instruction

You can’t operate the wire controller while using the APP

• Tear off the double-sided adhesive tape and stick it on the wired remote controller. Then paste the remote controller to the proper position of the motorcycle.
• IP65 Waterproof Level (It can be used normally on rainy days)
• The remaining cables can be tightened and hidden with a cable tie.

GPS Module(Optional)

• Tear off the double-sided adhesive tape on the bottom of the GPS module and attach it to the proper position of the motorcycle (Note: The “GPS” icon of the GPS shell must face to the sky directly.
• There can’t be anything above it, in case of the signal be shielded)

Images Information and Menu Description

1. After selecting, press to enter Recording Mode.
2. The icon becomes larger to indicate that the function is selected.

Character description on the display in recording mode

1. After selecting, press to enter Playback Mode.

2. The icon becomes larger to indicate that the function is selected.

3. Press to select the video to playback

1. After selecting, press to enter Setting Mode.
2. The icon becomes larger to indicate that the function is selected.

vibration sensitivity when parking
7. Recording Time After Flameout

(Configure BAT power cable)

| Set recording time after flameout
8. Button sound| On/off
9. Voice prompt| On/off
10. Clock setting| Day&Time
11. Date format| 3 options, YYYY MM DD/MM DD YYYY/DD MM YYYY
12. Speed watermark| Whether it is necessary to turn on/off the driving speed display when playing video on the computer
13. Unit system| Set the speed unit selection displayed when driving
14. Rear camera mirror| Whether mirror selection is required for the rear camera display
15. LCD Power Save| Set the display screen backlight to be off, or off after 1 min/3min
16. Protect Level| G-Sensor sensitivity level adjustment
17. GPS status| Shows the current received GPS satellite data and signal strength
18. Time zone selection| Time zone selection around the world
19. System reset| Restore to the factory default settings
20. WiFi mode| On/off
21. Format SD card| Delete all videos from the memory card
22. FW version| Information about the current software version of the recorder

1. After selecting, press to enter Language Choosing Mode.
2. The icon becomes larger to indicate that the function is selected.

• Language identification — Corresponding to the selected language.
• The number of language choices depends on the actual model!
• The specific function depends on the actual situation.

Quick Installation Guide

Quick test

1. Connect the front and rear cameras to the host of the recorder.
2. Find the USB test cable from the accessories and connect the recorder with a 5V2A or above power bank or USB charger. After the recorder is turned on, test the function of the recorder.
3. After the test shows that the recorder is normal, you can install it.

• If the output voltage exceeds 5V, the recorder may be burnt.
• After receiving the recorder, please connect the power bank or charger plug with the test cable. After the test is complete, then install it on the motorcycle.

Install products

Shock Absorption Camera Bracket

• Install the camera body on the bracket, and tighten the screws to fix it after adjusting the proper angle.

During installation, it is recommended to install the extension cable first, and then connect the host and camera separately (so that the installation is easier). If the distance between the main unit and the camera is less than 0.5 meters, it is recommended not to use the camera extension cable (please keep the camera extension cable for future needs).

Installing the power cable

• ACC Power Cable Connection Method: The red wire is connected to the positive pole of the motorcycle battery, the black wire is connected to the negative pole, and the yellow wire is connected to the positive pole of the motorcycle key control (12V ACC power source).
• A test is required after connection. After the motorcycle power is turned on, the recorder will turn on automatically. After the motorcycle flameout, the recorder is turned off. If you do not know the circuit of the motorcycle, it is recommended to find a professional to install it.

Troubleshooting

Scenes| Malfunction

Phenomenon

| Cause/Solution
---|---|---

Startup Process

|

Cannot startup

| ① Use the USB power cable to test whether it can start up Please don’t insert the card, don’t connect the front and rear

②cameras, and see whether it can be turned on. If you can’t turn it on, please contact customer service.

No recording when starting up| Please check whether the TF card is in good condition. Please format the TF card, or replace the TF card.

Recording Process

| Image upside down| ① Please check whether the camera is installed upside down.

②

Water ripple| The picture flickers, water ripples. Please check whether the installation location is strong.
Cameras have no image| Please swap the front and rear cameras to determine whether it is a camera problem or a main unit problem.
Video blurred| Please check the camera for dirt and fingerprints;
Foggy| Before recording, please wipe the camera with a dust-free cloth.

Wrong recording time

| d①Find the time and date option in the menu settings, set the date and time manually, or connect to WIFI to enter the APP

update the time automatically.

a②f If the DVR has GPS, it will also update to the current time m for GPS positioning. If the GPS update time is different from

the current time, please check the settings menu to see whether the time zone option is the local time zone.

WiFi Connection Process

|

The display is always on/ Rest screen

| s①c By default, the DVR will not operate after 1 minute, and the

② reen will shut down automatically.

If you want to keep the DVR’s display screen always light

on. You need to find the “LCD Power Save “option in the menu setting interface and set it to off.

Can’t find WiFi| Please check whether the WiFi is turned off. You can check whether WiFi is turned off in the menu setting interface.
The WiFi password is incorrect| Find the reset system in the settings interface to restore factory settings. The default password is 1234567890
WiFi connection failed| After turning off the WiFi function of the mobile phone, turn on the WIFI function and connect to the WiFi again.
WiFi has been connected to the APP, but there is no image, or the command failed| For Android, please turn off the WiFi helper and turn off the 4G network. Reconnect to WiFi.

Notes

• This product is an auxiliary (vehicle driving recorder) product for safe driving. Any loss caused by malfunction, information loss, or use of this product is irrelevant to our company.
• This product is an auxiliary device for recording external images of vehicles. Due to the different driving environments and vehicle environments, some functions will not be supported. The unscheduled firmware upgrade to improve the product will change the performance of the product, and sometimes the camera cannot be recorded due to the environment, so the driving images recorded in this product are for reference only. The state of the memory card will also lead to the camera not recording.
• Although this product can record and save videos of accidents, it does not guarantee that all the accident videos can be recorded. Slight collision accidents can’t start the collision sensor, so the video may not be recorded in the specialized folder.
• Be sure to disconnect the power supply when inserting or pulling out the memory card. For the stable use of the product, it is recommended to format the memory card twice a week.
• Generally, memory card has a service life. Long-term use of memory cards may cause the new data to be unable to be saved. In this case, it is recommended to buy a new memory card to use. Our company will not be liable for data destruction caused by the long-term use of memory card.
• Do not use a high-pressure water gun or chemical solvent to clean the host, camera, power module, and other parts (otherwise, no warranty will be given).
• Please do not use it in an environment with excessive dust density, to prevent cameras and other parts from being contaminated with dust, which will affect the video effect.
• Do not twist cables or cable connectors during installation, and keep the recorder host and wires away from high-pressure areas.
• Please replace the spark plug with a spark plug with the appropriate R-value if there is interference in some motorcycle models.
• Do not disassemble, modify, or repair this equipment by yourself. If the recorder fails due to this, we will not provide after-sales service.
• Some pictures, functions, and specifications may change due to product or software upgrades. Please understand that we cannot notify you separately.
• For your safety, please do not install or operate this product while driving. Please use it within the scope permitted by law.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>