sauermann Si-CA 230 Two Gas Industrial Emissions Analyzer Kit Instructions

: June 15, 2024
: sauermann

Table of Contents

sauermann Si-CA 230 Two Gas Industrial Emissions Analyzer Kit
Safety instructions
Introduction
General features
Parameter specifications
Perform a flue gas analysis
Perform a flue gas analysis
Set the general parameters of the analyzer
Set the parameters of the analysis
2 Oil / Domestic|
6 Oil / RFO|
Set the measuring unit
Perform other measurements
Maintenance of the analyzer
Optional accessories
Read User Manual Online (PDF format)
Download This Manual (PDF format)

sauermann Si-CA 230 Two Gas Industrial Emissions Analyzer Kit

Safety instructions

Before using the device, please read carefully this user manual. It delivers important information about the device operations, maintenance and storage.

Warnings

Interior or exterior use.
Do not expose the probe tip to an open flame.
Control device sealing with the probe.
Respect the range of the device measurement (0 to 60 bar)
After measurement and before clearing the device and accessories, wait for the probe to cool down. A hot probe can cause burns.
Condensate contain a low level of acidity, do not touch directly the condensate. Make sure no condensate is leaking into the device.
This device has been developed for the measurement of flue gas parameters. It must not be used in any other purpose.
This device has been developed, produced and sold exclusively to trained and qualified experts in the field of HVACR and combustion emissions monitoring. Appropriate training might be necessary in order to guarantee a riskless use of this instrument. Sagerman is not responsible for any possible accident during its use.
Please always use the device in accordance with its intended use and within parameters described in the technical features in order not to compromise the protection ensured by the device.
When using the device, the safety of the system integrating the device is the responsibility of the system assembler.
This device can pose a risk for wearers of pacemakers. Respect a distance of at least 10 cm (4″) between the device and the wearer.
Respect a safety distance with other electronic apparel like computers, credit cards, computers or TV screens which could be damaged by the magnetic field of the apparel.
Only the accessories provided with the device or available as an option must be used.
Do not use the device if it is damaged or if it operates abnormally. Inspect the device before every use. In case of doubt, please contact Sagerman’s After-sales service.
Do not authorize pressures beyond the device limits. Please refer to the technical features described in this user manual.
The device must not be exposed to rain or any other humid environments (> 85 %RH).
Do not use the device next to explosive and corrosives gases, vapour or dust.
Do not place your fingers in movable zones of the device (articulations).
The device must not be used in ATEX zones according to applicable standards.
Do not store the device with solvents. Do not use desiccants. Do not use isopropanol.
Do not obstruct the ventilation outflows of the device.
During use, keep inspecting the device and accessories for effective operation and your own safety.
Do not give this product to a child.
If the device falls or in case of similar inconveniences, or if an irregular malfunction appears, please send back the device to Sagerman After-sales service for a technical check and to ensure your own safety.

Environment protection
Send back the device at its end of working life to a waste collection center for electrical and electronic components (ac-cording to local regulations), or send it back to Sagerman to ensure a required waste collection in the respect of the environment.

Symbols used

For your safety and in order to avoid any damage of the device, please follow the procedure described in this user manual and read carefully the notes preceded by the following symbol
The following symbol will also be used in this user manual
Please read carefully the information notes indicated after this symbol.

Introduction

Analyzer description
The Si-CA 230 is a flue gas analyzer for emissions monitoring of boiler, engine, & other combustion applications with between two and six interchangeable gas sensors. Its main features are the following

Gas sensor options include O2, CO, NO, Low NO, NO2, Low NO2, SO2, H2S, CxHy (HC), Low SO2
CO Dilution auto-range with measurements to 50,000 ppm
Total NOx & Low NOx Capable
Large Color touch screen
Field Replaceable Pre-Calibrated Sensors
2000 points of memory
Mobile phone App for remote display and control
The gas analyzer is supplied with a 300 mm (12″) probe rated to 800 °C (1472 °F) with 3 m (10′) dual hose, an ABS hard plastic carrying case, a rubber holster, a water trap with filter, a charger with plug set, a USB cable, a quick start guide and a calibration certificate. (Longer probes available)
This gas analyzer is designed to measure parameters of flue gas in exhaust stream of combustion equipment. It can not be used in a permanently way and/or used as an alarm system.

Probe handle
Positioning cone (Adjustable)
Flue gas probe
Large color touch screen
On/off button
Min-DIN connection for optional CO and CO2 ambient air probes
Thermocouple connection for air temperature
Thermocouple connection for flue gas temperature
P- connection
P+ connection
Gas connection (Coming from water trap)
USB C connection

Main features

Screen

Color touch screen, 10.9 cm (4.3’’), 480 x 272 pixels with backlit. It allows to display measured parameters in a more comfortable format for the operator. Thanks to the zoom function, you can view on the screen the measured values in increased or decreased characters.

Battery charger

The instrument is supplied with a 5 V, 2 A power adapter to charge the internal batteries. The current loading is indicated by a battery symbol on the top right of the screen. To ensure a complete charge, the battery charging time is 6.5 hours. The voltage of the power supply is 100-240 VAC, 50/60 Hz. The USB cable included with the analyzer connects the power supply to the device.

Information about the low battery and power charging

When the battery of the analyzer is too low, the analyzer will make a purge before turning off.
When the analyzer is turned off and connected to USB or to the power supply, screen of the analyzer displays: “Device charging”.
If the analyzer is turned on and connected to USB or to the power supply, the power charging icon will be dis-played on the top of the screen.

• Flue gas suction pump

The pump, inside the gas analyser, is a diaphragm pump with a motor. It is energized in direct current directly by the in-strument in a way to get an optimal suction of flue gases.

Flue gas probe

Probe in stainless steel with a handle in plastic, with a standard length of 30 cm (12″) and with an adjustable positioning cone to maintain the contact tip inside the duct. The probe is connected to the instrument by 3 m (10′) of dual hose. Other probe lengths (75 cm, 1 m and 1.5 m) are available as options.

Interchangeable measurement sensors

The analyzer uses electrochemical sensors to measure the oxygen and the carbon monoxide (compensated in H2 hydro-gen). Measurement sensors (including NO, Low NO, NO2, Low NO2, SO2, Low SO2, CxHy
and H2S) are interchangeable. Regularly recharge the battery to guarantee an optimal operating of the electrochemical sensors. It is absolutely necessary to avoid falling to 0% battery as this would irreversibly
damage the cells.

Temperature sensors

Flue gas temperature is measured with a thermocouple integrated in the contact tip. The connection to the analyzer is made thanks to a single male type K thermocouple (nickel-nickel chromium) connector for measurements up to 1250 °C (2282 °F).
The instrument has a NTC thermoresistance sensor for the measurement of internal temperature; this sensor is also used for the measurement of ambient temperature.
If a temperature control of the combustive air must be performed directly by the supply duct (e.g.room sealed boiler), a TcK temperature probe can used. It is recommended to perform this measurement to make the efficiency calculation of the installation more precise.

Pressure sensors

The standard semiconductor type pressure sensor can measure draft and differential pressure (deltaP) for a range of ±200 mbar (±80 in WC). An optional high accuracy pressure measurement can be added for a
range of ±500 Pa.

Supply input of flue gases and +/- pressure

There are two hose connections coming from the probe that connect to the bottom of the analyzer. One comes from the water trap assembly and connects to the gas inlet (labelled “G” and colored black) while the other connects to the high pressure inlet (labelled “P+” and colored orange).

Fuel types

The analyzer is supplied with technical data which characterizes the most common fuels. It is also possible to add user defined fuels and their corresponding coefficients if needed.

Calibration certificate

The analyzer is calibrated by comparison with standard of metrology laboratories, which are periodically certified closed to laboratories known at the international level. Each analyzer is supplied with its calibration certificate in which, for each measured parameter, are indicated the nominal value, the one measured, the admitted error limits and the found error. It is advised to calibrate the instrument at least once a year.

Water trap

The analyzer has an external water trap assembly that hangs directly below the analyzer. The flue gas is cooled and dried in the lower chamber. Accumulated condensate must be manually drained as needed. The upper chamber has a filter car-tridge to remove dust and particulates from the flue gas. The filter should be replaced periodically as needed.
THE WATER TRAP MUST BE IN VERTICAL POSITION AT ALL TIMES DURING OPERATIONS FOR OPTIMAL PERFORMANCE!
The water trap must be emptied before storing it in the transport case.

CO dilution
The instrument has the CO dilution function to prevent high CO concentrations from over saturating the CO sensor. These high concentrations can damage the analyzer and the CO sensor. This function allows high CO measurements without damaging the sensor. In dilution function, the measuring range becomes 0-5% (50 000 ppm).

Measured and calculated values

The following parameters are displayed according to your analyzer model

O2: Direct O2 sensor measurement (also for Heat Exchanger Test)
CO: Direct CO sensor measurement (also for Heat Exchanger Test)
NO: Direct NO sensor measurement
NO L: Direct Low NO sensor measurement
NO2: Direct NO2 sensor measurement
NO2 L: Direct Low NO2 sensor measurement
SO2: Direct SO2 sensor measurement
SO2 L: Direct Low SO2 sensor measurement
H2S: Direct H2S sensor measurement
CxHy: Direct CxHy sensor measurement
CO(O2): Corrected CO sensor measurement for chosen O2 Ref. level
NO(O2): Corrected NO sensor measurement for chosen O2 Ref. level
NO L(O2): Corrected Low NO sensor measurement for chosen O2 Ref. level
NO2(O2): Corrected NO2 sensor measurement for chosen O2 Ref. level
NO2 L(O2): Corrected Low NO2 sensor measurement for chosen O2 Ref. level
SO2(O2): Corrected SO2 sensor measurement for chosen O2 Ref. level
SO2 L(O2): Corrected Low SO2 sensor measurement for chosen O2 Ref. level
H2S(O2): Corrected H2S sensor measurement for chosen O2 Ref. level
CxHy(O2): Corrected CxHy sensor measurement for chosen O2 Ref. level
NOx : Calculated NOx value
NOx L: Calculated Low NOx value with NOx factor
NOx (O2): Corrected calculated NOx for chosen O2 Ref. level
NOx L (O2): Corrected calculated Low NOx for chosen O2 Ref. level
CO2: Calculated CO2
Eff. (η): Net Combustion Efficiency
Eff. (η+): Gross Combustion Efficiency
Loss (Q): Stack Heat Losses (net)
Loss (Q+): Stack Heat Losses (gross)
CE (ηc): Condensation efficiency calculated acc. to the UNI 10389-1 standard
X Air: Calculated excess air
Lambda: Calculated lambda value (for air to fuel ratio)
Air Ind (n): Calculated air index
PI : Calculated CO to CO2 Ratio, also called poison index
P : Differential pressure (also for Gas Tightness Test)
Draft : Draft (static pressure) measurement
T flue : Flue gas temperature
T air : Air temperature
T : Differential temperature
T dp : Calculated dew point temperature
CO AF : Calculated CO Air Free = CO corrected for 0.0% O2 Ref. level
COcorr : Calculated value for Corrected CO = Lambda x Measured CO
CO Amb: Ambient CO measurement using external probe
CO2 Amb: Ambient CO2 measurement using external probe
Velocity : Calculated Stack Gas Velocity
K Value : Constant value used for velocity calculation
Volumetric Flow Rate : Calculated Stack Gas Volumetric Flow Rate
Mass Flow Rate : Calculated Stack Gas Mass Flow Rate
CO Monitor (Current & Max): CO measurement for room safety
Pump Flow Rate : Measured flow rate of flue gas through the analyzer
ΔO2: O2 Variance during Heat Exchanger Integrity Test
ΔCO: CO Variance during Heat Exchanger Integrity Test
Stack Cross Sectional Area: Input for Stack Cross Sectional Area
O2 Reference: Input for O2 Reference Level
NOx Factor: Input for Assumed NO to NO2 Ratio
moke/Soot : Smoke index value
Atmospheric Pressure: Input for Atmospheric Pressure

Displaying of measurements
When a value is out of range or unavailable, “—” will be displayed on the screen.

Conformity and standards

The analyzer complies with 2014/53/EU (RED) and 2015/863 EU (RoHS 3). Document available on request .Moreover, the analyzers complies with EN 50379-1 and EN 50379-2, UNI 7129; UNI 11137, UNI 10389, UNI 10845, UL & cull Certification, BS 7967:2015, BS EN 50543:2011, UNE 60670-10 and ES.02173.ES
The analyzer was tested in accordance with the requirements of VDI 4206 – TÜV RgG 323 part 1.
Hereby, Sagerman Industry SAS declares that the radio equipment type Si-CA 230 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: sauermanngroup.com

FCC rules

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference’s by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by Sagerman could voice the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions

This device may not cause interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Canadian standard
This device contains licenceexempt transmitter(s)/receiver(s) that comply with innovation, Science and Economic Development Canada’s licenceexempt RSS(s). Operation is subject to the following two conditions

This device may not cause interference
This device must accept any interference, including interference that may cause undesired operation of the device.

When the analyzer is first started up, parameters of the analyzer must be set.
Keep pressed for 3 seconds to turn ON the analyzer.
DO NOT insert the gas probe in the flue/chimney/stack at this time.
The probe can be inserted in the chimney.
The analyzer displays the measurements
The settings done during the first start-up can be reselected at a later time using the Settings menu.

General features

Dimensions

Parameter specifications

All accuracies indicated in this document were stated in laboratory conditions at 20 °C (68 °F) and can be guaranteed for measurement carried out in the same conditions.
Accuracy given for the analyzer only.
Accuracy given for the analyzer only.
For Higher Heating Value
For Lower Heating Value

Perform a flue gas analysis

Prepare the instrument before the analysis

During the measurement, the analyzer must be in vertical position to keep the water trap vertical. Do not hold the analyzer in inclined or horizontal position.
Before the 1st use of the analyzer, a full charge of the battery should be made for 12 hours. Do not leave the battery completely discharged.
Empty the water trap if any condensate is inside it and after every use before you store it. For this operation the instrument has to be turned OFF.
In case of any default or damage of the instrument, Sudermann After-sales service shall be contacted. On the back of the analyzer, there is a label with the analyzer serial number. This number shall be communicated for every operation (technical operation or request of spare parts). This number is also available in “Analyzer information” menu (see page 29).

Perform a gas analysis

Connect the flue gas probe to the analyzer. (Two hoses + thermocouple)
Turn ON the instrument.
Wait for the end of the autozero cycle (probe out of stack).

Gas analysis screen is displayed.

Insert the probe in the flue/stack as suggested on the figure.
Tap Menu icon .
The screen with the different possible item menu is displayed.
Tap “Gas analysis”.
The screen displays the measured and calculated values.
Tap the combustible fuel currently used on the top of the screen The list of available fuels is displayed .
Select the required combustible fuel and return to the Gas Analysis screen.
The screen displays values of the different parameters of the analysis.
Perform measurement for at least 3 minutes until measurements stabilize.

Turn ON and OFF the gas sampling pump

During a gas analysis, it is possible to turn off the gas sampling pump. Calculated and measured values will be then on hold.
During the measurements
To turn OFF the gas sampling pump

Tap on the bottom right of the screen.
The pump stops and values are on hold.

To turn ON the gas sampling pump

Tap on the bottom right of the screen.
The pumps restarts and values are measured.

Visualize data as graph

It is possible to visualize the measured data as graph.

During the measurements

Tap
Tick the boxes to select one or to parameters to display.
Select the time period to display.
Tap “Start”.
The analyzer displays the measurements as graph.

Save the analysis
During the combustion gas analysis, when measurements are constant, it is possible to save the gas analysis data to a previously created data folder or to a newly created folder.

Tap .
The analyzer displays the list of recorded folders.
Select a folder or create a new folder.
If creating new folder, type in the folder name and then save by tapping on icon. Then select new folder after it has been created and saved.
Tap “Save”.

The analyzers returns to the measurement screen of the analysis after the data point is saved.

Print the analysis results

It is possible to print the results on the ticket with the optional printer accessory.
The printer must be connected via the wireless connection to the analyzer. See page page 28 to connect and set up the printer.
Tap during the analysis.

Measured values are printed on the ticket.
Use the Zoom function
From the gas analysis screen, the zoom function is available using The initial screen displays 8 measured values.

To zoom in, tap
- The screen displays 4 values.
To zoom in again tap
- The screen displays 2 values.
To zoom out, tap
- The screen displays 4 values.
To zoom out again, tap
- The screen displays 8 values.
To zoom out again, tap
- The screen displays 12 values.

Perform a flue gas analysis

Set the general parameters of the analyzer

The settings menu allows to set the general parameters of the analyzer:

Time
Time zone
Date
Language
Country
Wireless connection
Autozero
Purge time
Brightness

Any changes made to settings are automatically saved when you exit the screen.

Set the time
“Settings > General” screen is displayed.

Tap “Time”.
Set the time and select the hour format (24 hours and AM or PM).

Set the time zone

“Settings > General” screen is displayed.
Tap “Time Zone”.
Set the time zone.

Set the date
“Settings > General” screen is displayed.

Tap “Date”.
Set the date and the date format (Month-Day-Year or Day-Month-Year)

Set the language

“Settings > General” screen is displayed.

Tap “Language”.
Select the language among English, French, Spanish, Italian, German, Portuguese and Chinese.

Set the country
“Settings > General” screen is displayed.

Tap “Country”.
Select the country from available list. If desired country is not on list, then select area of the world (EMEA, AMERI-CAS, APAC) show at the bottom of the country list.

Set the autozero
This part allows to set the autozero duration. “Settings > General” screen is displayed.

Tap “Autozero”.
Select the autozero duration : 30 s, 60 s, 120 s or 180 s (default value is 60 s).

The manufacturer recommendation is a minimum of 60 seconds for most applications.

Set the purge time
This part allows to set the purge time duration. “Settings > General” screen is displayed.

Tap “Purge time”.
Select the purge time: 15 s, 30 s, 60 s or 120 s.

Set the self-extinction
It is possible to activate a self-extinction on the analyzer: it will turn off after a certain period of time of non-use. From main menu

Tap “Settings”.
Tap “General”.
Tap “Self extinction”.
Activate the self extinction on top of the screen.
Select the period of time: 1 hour or 2 hours.

Before turning off, the analyzer will make a purge.

Set the brightness of the screen
“Settings > General” screen is displayed.

Tap “Brightness”.
Set the brightness level from 1 to 5.

Reset to factory setting
It is possible to set the analyses with its factory setting.
From main menu

Tap “Settings”.
Tap “General”.
Tap “Factory settings”.
Tap “Reset and restart”.

The analyzer will be reset to original delivery settings. All your configurations will be deleted.

Units and values of measurement settings of the factory setting

Purge time : 30 s
Autozero: 60 s
Stack cross sectional area : 10 cm²
Saving interval : 10 s
Saving duration : 5 s
Reference O2 : 20.9%
NOx factor : 1.05
Atmospheric pressure : 1013.25 mbar
Air temperature : 21.5 °C
K value : 0.84
Smoke soot : 2
Smoke soot : disable
CO dilution threshold: 1200 ppm
CO cut-off threshold: 2000 ppm
CO cut-off : enable
Pump after autozero: deactivated

Set the parameters of the analysis

This menu allows to set the following items regarding the analysis

Fuel|

Alarms

---|---
CO dilution mode|

Pump after autozero

CO dilution threshold|

Zero draft sensor

CO pump cut-off level|

Atmospheric pressure

Reference O2|

Air temperature

NOx factor|

Display configuration

Smoke/soot|

Stack cross-sectional area

Set the fuel
This part allows to select the required fuels for the gas analysis but it also allows to add customized fuels.

Select the fuel
The default list of fuels is dependent on the country selected. Possible fuels listed include the following

Natural Gas (H)|

Biogas

---|---
Natural Gas (L) Groningue|

Firewood 20% (Soft)

Natural Gas North America|

Firewood 50% (Soft)

2 Oil / Domestic|

Firewood 20% (Hard)

#3 Oil / Heavy|

Firewood 50% (Hard)

6 Oil / RFO|

Wood Chips / Pellets 8%

Propane|

Cannel Coal

Butane|

Low Volatile Coal

LPG|

Hog Fuel

Biofuel 5%|

Peat

Diesel|

Biomass

Coke Gas|

“Settings > Analysis” screen is displayed.

Tap “Fuel”.
Select the required fuel.

To see features of the fuel, tap on it. The following information about the fuel is displayed: A1, B, K, CO2t(%), V dry gas (m3/ucb), M air (kg/ucb), MH2O (kg/ucb) and PCI (MJ/ucb)

7.1.2 Create a fuel

is possible to create a customized fuel.“

Settings > Analysis” screen is displayed.

Tap “Fuel”.
Tap “Add fuel” on the bottom of the screen.
Name the fuel and validate it tapping
Enter the following features of the fuel: A1, B, K, CO2t(%), V dry gas (m3/ucb), M air (kg/ucb), MH2O (kg/ucb) and PCI (MJ/ucb).
Tap “Save”.

The customized fuel is then integrated at the end of the fuel list.
If a very specific fuel must be created please contact the Sauermann Service Center for further information.

A customized fuel can be deleted

Tap the name of the customized fuel on the fuel list.
Features of this fuel are displayed.

Tap on the top of the screen.

A message is displayed asking to confirm the deleting.
Tap Yes to confirm.

Set the CO dilution mode
This part allows to activate the CO dilution mode. The CO dilution allows to bring fresh air to the analyzer and so to dilute the CO.

The folowing choices can selected for the CO dilution

AUTO: dilution is activated once the CO value exceeds the defined threshold value (see chapter 7.3 “Set the CO dilu-tion threshold” on page 20)
ON: dilution is activated continuously.
OFF : dilution is inactivated

“Settings > Analysis” screen is displayed.

Tap “CO dilution mode”.
Select “AUTO, “ON” or “OFF”.

The manufacturer recommendation is to set to AUTO for most applications.

When dilution is activated, will be displayed on top of the screen and in front of the CO line on the measurement screen.

Set the CO dilution threshold
This part allows to define the CO dilution threshold. “Settings > Analysis” screen is displayed.

Tap “CO dilution threshold”.
Enter the required threshold between 100 and 4000 ppm.

Set the CO pump cut-off level
This part allows to define the CO pump cut-off level. “Settings > Analysis” screen is displayed.

Tap “CO pump cut-off level”.
Enter the required level between 1000 and 8000 ppm.

To enable the CO pump cut-off level, activate the protection at the top of the screen.
In normal operation it is recommended to set the CO pump cut-off level threshold higher than the CO dilution threshold.

Set the Reference O2
This part allows to set the oxygen reference level to use when corrected emissions calculations are needed. “Settings > Analysis” screen is displayed.

Tap “Reference O2”.
Enter the required reference O2 in percentage between 0.0 and 21%.

Set the NOx factor
This part allows to set the NOx factor, which is the assumed NO to NO2 ratio used to calculate NOx when the NO sensor is included but the NO2 is not included. The same applies when NO and NO2 are low range sensors.
“Settings > Analysis” screen is displayed.

Tap “NOx factor”.
Enter the required NOx factor in percentage between 1.00 and 1.50.

Set the Smoke/soot index
This part allows to enter the smoke or soot index obtained with an external pump (available as option). An inputted smoke value will be included with saved data points.
“Settings > Analysis” screen is displayed.

Tap “Smoke/soot”.
First activate the function at the top of the screen to enable the smoke value to be entered.
Enter the smoke/soot index between 0 and 9.

Set the alarms

This part allows to set an alarm for parameters measured and calculated by the analyzer.
This alarm can be rising (the alarm of the instrument is activated when the measured value exceeds the defined threshold) or falling (the alarm of the instrument is activated when the measured value is below the defined threshold).
A maximum of 5 different alarms can be set.

“Settings > Analysis” screen is displayed.

Tap “Alarms”.
Tap on one of the five listed alarms to first set it up.
Select the parameter in which the alarm will be activated on the “Parameter” line.
Enter the threshold value on the “Value” line.
Select either high threshold or low threshold alarm.
Return to main Alarm screen and tap on the activate button in order for the alarm to be enabled.
Repeat the procedure for other alarms as needed.

Alarms can be revised later (for example, different threshold value) if needed.
During the measurements, an alarm remains ON even if the measurement goes below or above the threshold value until it is acknowledged.
If the alarm is acknowledged and the value is always in alarm, the alarm remains ON.

Zero draft sensor
This part allows to reset the draft sensor and the high accuracy sensor (if this optional sensor is installed on the analyzer).. “Settings > Analysis” screen is displayed.

Tap “Zero Draft Sensor”.
Remove the smoke probe from the stack and leave the analyzer pressure connectors free of use.
Tap “Start”.

The draft sensor is re-zeroed (takes a few seconds to complete).

Set the atmospheric pressure
This part allows to set the atmospheric pressure in which measurements are performed. This value is taken into account in calculations such as the smoke velocity. It is set to 1013 mbar by default.
“Settings > Analysis” screen is displayed.

Tap “Atmospheric pressure”.
Set the atmospheric pressure between 500 and 1100 mbar.

Set the air temperature
This part allows to set the air temperature for the incoming air into the combustion equipment if known. This value is obtained by three different ways:

by an external probe if this optional probe is connected
entered by the user if no probe is connected
by the internal NTC sensor of the analyzer if no probe is connected and if no value entered

To enter an air temperature
“Settings > Analysis” screen is displayed.

Tap “Air temperature”.
Activate it at the top of the screen.
Enter the required air temperature.

Set the display configuration
This section is used to organize the display of values on the gas analysis screen. “Settings > Analysis” screen is displayed.

Tap “Display configuration”.
Tick the parameter boxes for the parameters that are to be shown on the gas analysis screen.
Use up and down arrows to move values up or down on the gas analysis screen to put the parameters in the de-sired sequential order.

Set the stack cross-sectional area
This part allows to define surface of the stack cross-sectional area that will help to measure the stack gas velocity. “Settings > Analysis” screen is displayed.

Tap “Stack cross-sectional area”.
Enter the surface between 0 and 99,999 cm2.

Set the measuring unit

This part allows to define the measuring unit for each parameters measured or calculated by the analyzer. The following unit is available according to the parameter

Temperature : °C, °F
Pressure : mbar, iwg (inches water gauge), mmwg, mmHg, Pa, hPa, kPa, psi
Gas concentrations: ppm, mg/m3, %, mg/kWh, g/GJ, g/m3, g/kWh, g/hp
Excess air : %, — (no unit)
Stack gas velocity: m/s, f/m, km/h, mph
Volumetric flow rate : m3/m, cf/m
Mass flow rate : kg/h, lb/h, t/d
Stack cross-sectional area : cm2, in2
CxHy: %, ppm

“Settings” screen is displayed.

Tap “Measuring units”.
Tap the required parameter to set.
Select the required unit in the list.

This part allows to define the data saving mode: manual or data logger “Settings” screen is displayed.

Tap “Data saving”.
Select “Manual”: data will be manually saved during measurement.
Select “Data logger” : data will be saved according to a specified time interval and duration.
Define the time interval between 10 and 600 seconds (by default time interval 10 seconds and duration 10 min). This time interval is for how often data points will be saved and to respect a maximum of 60 points per campaign.
Tap “Next”.
Define the duration between 1 and 120 minutes. The duration is the total time for the entire test period.
Tap OK.

Data will not be saved until initiated on the gas analysis screen (see chapter “It is possible to visualize the measured data as graph.” on page 15) Only displayed values are saved.
When combustion analysis is on hold, saving and printing data are possible.

The following screen will be displayed if the memory is insufficient

Tap “Change setting”.
Modify the time interval or the duration.

This part allows to set the printer specifications: printer connection, custom header and number of copies. This printer is available as option.

Set the printer connection
“Settings > Printer” screen is displayed.

Turn on your wireless printer.
Tap “Printer connection”.
Activate the “Wireless printer mode” button.
ap “Search for printers”.

The analyzer searches for available printers and then displays the results.

Tap the required printer.

The analyzer can not be connected to the app and the printer at the same time. If the analyzer is connected to the app, disconnect it from the app and then search again for printers.

Custom the printing header

Tap to change capital letters and numbers to/from lower case letters and symbols.

It is possible to customize the header of the ticket with you own contact details. “Settings > Printer” screen is displayed.
Tap “Custom header”.
Enter your own information.
Tap the validate sign at the bottom right of the screen.

Set the number of copies
It is possible to set the number of copies that will be printed (default number is 1). “Settings > Printer” screen is displayed.

Tap “Number of copies”.
Use up and down arrows to define the number of copies. Maximum number of copies is five.

This part gives information about the analyzer

Service and Calibration
Gas sensor information
Model number
Serial number
Firmware version
Battery status
Memory status (how much memory is available) From the main menu of the analyzer:
Tap “Analyzer information”.

Service and Calibration
Calibration information
This screen gives calibration information about gas sensors installed into the analyzer. “Service / Calibration” screen is displayed.

Tap “Calibration Information”.

The following information is displayed for each installed gas sensor that can be selected

Date of Last service center calibration
Date of last user calibration
Due date of next service center calibration
Tap “Contact Service Center” at the bottom of the screen, the address where the analyzer should be sent is displayed.

Service center contact
“Service / Calibration” screen is displayed.

Tap “Service Center Contact” to display the address of the Sauermann Service Center.

Perform calibration
This screen allows the user to perform a calibration on a gas sensor.

The calibration must be performed by a qualified technician.
All modifications performed in this menu will affect the measurement values. If false manipulations are done, measurement values will be wrong.

“Service / Calibration” screen is displayed.

Tap “Perform Calibration”.
Enter the code to access to calibration.

To get your code, please contact the Service Contact. Our team will explain how to get this code.

Tap ”Access Calibration”.
Select the gas sensor on which the calibration must be applied.
Enter the new reference value then tap Start.

The analyzer performs the measurement for a defined time and displays the following information

Measurement
Sensor current
Reference value
During the measurement, if values are correct, tap “Validate adjustment” on the bottom of the screen.
Tap “Save adjustment” to apply the calibration on the gas sensor.
Tap “Restart analyzer” for changes to be taken into account.

Gas sensor information
This screen gives information about the gas sensor installed on the analyzer. “Analyzer information” screen is displayed.

Tap “Gas sensor information”.
Tap the gas sensor on which information must be displayed.

The following information is displayed

Type of sensor
Serial number of the sensor
Measuring range of sensor
Date of last calibration
Date of installation
Output current (in units of micro amps)
Sensor life estimation: a four bar display is shown. When down to one bar, it is recommended to contact an authorized Sauermann service center

Other information
Analyzer information screen also gives the following information

Model number / Serial number
Firmware version
Battery status
Memory status

Please provide the model number and serial number for contact with the manufacturer or the Service Center.

Perform other measurements

The analyzer can perform other measurements than a gas analysis

CO monitor
Gas tightness test
Gas/pump flow rate
Heat exchanger integrity test
Stack gas velocity
Draft

Perform CO monitoring
The CO monitoring is performed with the external CO probe (available as option) or with the internal CO sensor.

Connect a CO probe (available as option) on the DIN connection on the bottom of the analyzer (if the CO probe is used).
Turn on the analyzer.
Tap “Menu” then “Other Measurements”.
Tap “CO monitor”.

The measurement is launched, the instrument displays the current level of CO, the maximum level of CO, and the duration of the test. The maximum CO level and duration are reset each time the CO Monitor screen is entered.

If the internal sensor is used, the main pump will be ON and if the CO probe is used the main pump will be OFF.

Perform a gas tightness test
To perform this test, it is necessary to have a Differential pressure hose kit. This kit is available as option (ref: KEG3).
Perform a gas tightness test according to UNI 7129 (new piping)

Connect the hose to the gas analyzer P+.
Connect the hose to the piping system.
Select the piping system: UNI 7129 (new piping)
Select the estimated volume: < 100 dm3, 100-250 dm3 or 250-500 dm3.
Select the fuel: natural gas or LPG
Pressure the pipe up to 150.00 hPa.
Tap “Start stabilization”.

The analyzer starts the stabilization which takes 15 minutes.
At the end of the stabilization, the analyzer starts the test and then displays the following results

P1
P2
Pressure drop
Pressure drop allowed
According to the results, the analyzer will display if the test is compliant or not compliant.

Perform a gas tightness test according to UNI 11137 (existing piping)

Connect the hose to the gas analyzer P+.
Select the piping system: UNI 11137 (existing piping)
Select the test type: Preliminary test (< 18 dm3) or Indirect test (>18 dm3 up to 35 dm3)

If Preliminary test is selected

Select the fuel: natural gas or LPG.
Read the gas pressure inside the pipe.
Tap “Start stabilization”.

The analyzer starts the stabilization.

Tap “Start test” once the stabilization is completed.

At the end of the test, the analyzer displays the following results

P1
P2
Pressure drop
Pressure drop allowed
According to the results, the analyzer will display if the test is compliant or not compliant.

If Indirect test is selected

Select the fuel: natural gas or LPG.
Select the test gas: fuel or air.

If the volume is known

Enter the known volume of the installation between 19 and 999 dm3.
Connect the hose to the piping system.
For test with gas, read the gas pressure inside the pipe.
For test with air, pressure the pipe up to 22 hPa for natural gas pipeline or 30 hPa for LPG pipeline.
Tap “Start stabilization”.

The analyzer starts the stabilization.

Tap “Start test” once the stabilization is completed.
- At the end of the test, the analyzer displays the following results:
P1
P2
Pressure drop
Leakage rate
Maximum leak allowed
According to the results, the analyzer will display if the test is compliant or not compliant.

If the volume is unknown

Connect the hose to the piping system.
For test with gas, read the gas pressure inside the pipe.
For test with air, pressure the pipe up to 22 hPa for natural gas pipeline or 30 hPa for LPG pipeline.
Tap “Start stabilization”.

The analyzer starts the stabilization.

At the end of the stabilization, extract a volume from pipeline using the Syringe (20 or 100 ml).
Select the volume extracted (20 or 100).
Wait for the pressure stabilization (minimum 1 min) before tapping “Refill done”.
The volume measurement is shown.
Tap “Start test”.

At the end of the test, the analyzer displays the following results:

P1
P2
Pressure drop
Leakage rate
Maximum leak allowed
According to the results, the analyzer will display if the test is compliant or not compliant.

Gas pump flow rate
This screen shows the real-time measured flow rate of the gas passing through the analyzer as performed by the main flue gas sampling pump. This menu also allows to measure the tightness of the analyzer and the probe.
Display the pump flow rate

The pump of the analyzer must be turn on. “Other measurements” screen is displayed.

Tap “Gas/pump Flow Rate”.

The analyzer displays the flow rate of the pump in L/m.
Perform a tightness test

The pump of the analyzer must be turn on.

Block the extremity of the probe.

“Other measurements” screen is displayed.

Tap “Gas/pump Flow Rate”.

If the flow rate displayed is between 0 and 0.3 L/min => there is no leak.
If the flow rate displayed is greater than 0.3 L/min => there is a leak. Please contact the Sauermann After-sales service for a technical check.

Heat exchanger integrity test
This test provides information to help determine if there might be a crack or leak in the heat exchanger and/or combustion chamber.

The pump of the analyzer must be on to perform this test. “Other measurements” screen is displayed.

Tap “Heat Exchanger Integrity Test”.
Insert the sampling probe into the exhaust flue/pipe.
Turn on the heating equipment (with the blower off) and let the O2 & CO measurements stabilize on the analyzer screen.
Tap Start icon on the bottom of the screen to start the Heat Exchanger Integrity Test on the analyzer right before the blower turns on. Make sure the blower turns on during the first 30 seconds of the test period.
The results of the test will calculate the amount the O2 and CO measurements varied during the 60 second test period. The greater the variances, the more likely there is to be a crack or abnor-mality with the heating system that should be investigated by a heating professional.

Perform a Stack Gas Velocity measurement with a Pitot tube

To perform this test, it is necessary to have a Pitot tube Type L or Type S.

Place and connect the L Pitot tube

The Pitot tube must be introduced perpendicularly, in the middle into the duct and parallel to the flow. The head (ending with an ellipsoidal nose) must be maintained parallel and facing the flow.
The total pressure (+) caught by the nose, is connected to the P+ at the bottom of the analyzer.
The static pressure (-) caught by the holes of the head, is connected to the P- at the bottom of the analyzer.

Place and connect the S Pitot tube

The S-type Pitot tube is inserted into the stack and rotated until the differential pressure measurement is greatest for a given location in the stack. The proper orientation is for the high pressure side of the S-type
Pitot tube tip to face into the direction of the stack gas flow as shown in the diagram.
The holes must be perfectly aligned with the air or gas flow direction.
The Pitot tube S is more sensitive to alignment errors than the Pitot tube L.
The connecting to the measurement device must be carried out like following:
The leg in front of the air flow is connected to the P+ sign of the analyzer.
The leg at the opposite of the air flow is connected to the P– sign of the analyzer

When the connections are made and “Other measurements” screen is displayed

Tap “Stack Gas Velocity”.
The analyzer displays the following measurements: Velocity, Volume flow and Mass Flow.
Tap the K value to modify it if necessary (K value must be between 0.0000 and 99.0000).
Recommended values are: 0.84 for S-Type Pilot tube and 1.0015 for L-Type Pilot tube.
For proper calculations of volumetric flow rate and mass flow rate, enter correct stack cross-sectional (see chapter “7.13 Set the stack cross-sectional area” on page 25)

Perform a draft measurement
The analyzer can measure the draft. This draft can be measured by the flue gas probe or the draft probe.

Tap “Menu” then “Other Measurements”.
Tap “Draft”.

Screen for the draft measurements contains 3 lines

Outside Air Temperature: ambient temperature manually entered. Default value: 15 °C / 59 °F
Draft: draft/pressure measured by internal pressure sensor
Normalized draft: calculated value of the draft at a temperature of 20 °C / 68 °F
The outside air temperature can be manually changed. This value must be between -25 and +19.9 °C (-13 and 66.2 °F). Change the outside air temperature from the “Draft” screen:
Tap the blue arrow on the “Outside air temperature” line.
Enter the required outside air temperature between -25 and +19.9 °C (-13 and 66.2 °F).
Tap “Outside Air Temp.” on the top left of the screen to back to the draft measurement screen.

Perform a draft measurement with the flue gas probe

Disconnect the water trap connector from the gas connection of the analyzer.
Plug the water trap connector with the blue cap.

The analyzer displays the draft without the influence of the main pump.

Perform a draft measurement with the draft probe
The draft measurement can be performed thanks to the draft probe available as option.

If the draft probe is used, it will be necessary to drill another hole dedicated to this draft measurement in the duct.
- Disconnect the P+ connector of the flue gas probe from the analyzer.
- Connect this connector to the blocked connection of the draft probe.
- Connect the orange connector of the draft probe to the P+ connection of the analyzer.
- Insert the draft probe into the duct.

Perform a measurement of smoke/opacity

It is possible to enter in the analyzer from 1 to 3 smoke/opacity indexes performed thanks to smoke/opacity pump avail-able as option.
The smoke/opacity index consists of the measurement of solid waste of combustion in the flue with a pump and a filter of measurement. The filter coloration is compared with a table reference composed by 10 greyed areas numbered from 0 to 9.

Perform the measurement

Preliminary operation: to avoid the condensation in the pump, it is necessary to breathe in WITH-OUT FILTER fresh air before performing a measurement

Put the paper filter in the pump.
Insert tip of pump into the flue/stack.
- The necessary gas volume for a measurement of opacity corresponds to about 10 pump strokes.
Compare the filter clogging to the reference table to determine the opacity index.
Make the same operation several times if necessary, replace the filter each time.

UK test
The UK test menu allows to access to different tests to perform according to UK regulations. The avalaible tests are the following:

CO Sweep
Room Safety
Let By

For CO Sweep and Room Safety tests, an external CO2 probe is needed. This probe is available as option. Please Contact Sagerman to get one.

CO sweep
From the main menu of the gas analyzer

Tap “Other measurements”.
Tap “UK Tests”.
Tap “CO Sweep”.
The test starts and lasts 20 minutes.
The analyzer displays the measured CO and CO2 in the room. It displays also peaks for these values. At the end of the test, the analyzer displays the maximum values of measured CO and CO2.
If the CO max is equal or lower than 10 ppm and the CO2 max is lower than 15,000 ppm, test is OK.
If the CO max is higher than 10 ppm and the CO2 max is higher than 15,000 ppm, test is not OK.
Print the results if needed by tapping at the bottom of the screen.
Save the results if needed by tapping at the bottom of the screen.
It is possible to stop the test at any time tapping at the bottom of the screen.

Room Safety
From the main menu of the gas analyzer:

Tap “Other measurements”.
Tap “UK Tests”.
Tap “Room Safety”.
Tap the required appliance in which the measurements must be performed.
The analyzer displays the measured CO and CO2 in the appliance. It also displays peaks for these values.
At the end of the test duration, the analyzer displays the measured CO max and CO2 max. According to these values, the CO level is normal or not.

Test durations are according to the appliance selected

Boiler: 15 minutes
Cooker: 20 minutes
Water heater: 5 minutes
Space heater: 30 minutes
Room seal appliance: 15 minutes

CO values above which measurements are not normal

Boiler: 10 ppm
Cooker: 30 ppm
Water heater: 10 ppm
Space heater: 10 ppm
Room seal appliance: 10 ppm
Print the results if needed by tapping at the bottom of the screen.
Save the results if needed by tapping at the bottom of the screen.
It is possible to stop the test at any time tapping at the bottom of the screen.

Let By
From the main menu of the gas analyzer:

Tap “Other measurements”.
Tap “UK Tests”.
Tap “Let By”.
Connect the tube to the P+ input of the analyzer
Tap “Start pressure autozero” then “Start stabilization”.
The analyzer perform a one-minute stabilization phase and displays the measured pressure.
At the end of the stabilization, the analyzer displays «Stabilization complete».
Tap “Validate stabilization” if the stablization has been satisfactory

Tap “Invalidate stabilization”

If the stabilization is not satisfactory, it’s possible to start a new stabilization:
- Tap “Invalidate stabilization”.
- Tap “New stabilization”.
If the stabilization is validated, the analyzer displays “Successful stabilization”.
- Tap “Start test”.
The test starts and lasts 2 minutes. The analyzer displays Pressure 1 (P1), Pressure 2 (P2) and the pressure difference (deltaP).
At the end of the test, P1, P2 and deltaP results are displayed and it’s possible to validate or invalidate the test according to your specifications.
- Tap “Validate test” or “Invalidate test”.
Print the results if needed by tapping at the bottom of the screen.
Save the results if needed by tapping at the bottom of the screen.
It is possible to stop the test at any time tapping at the bottom of the screen.

Maintenance of the analyzer

Life-time of the sensors
Gas sensors are electrochemical type: inside them, in the presence of gas to detect, a chemical reaction occurs that causes an emission of electrical current. The electric current strength detected by the instrument is converted into a correspond-ing gas concentration. The life-time of the sensor is strongly linked to the reagent consumption present in the sensor. As their consumption increases, features of the sensor are getting worse until their exhaustion, after which it is necessary to replace it. To ensure the measurement accuracy, sensors have to be calibrated only in Assistance center qualified by Sauermann.

Sensor	Average life-time	Required calibration
O2	4 to 5 years	Annual
CO-H2 (also used with dilution)	2 to 5 years	Annual
NO	2 to 5 years	Annual
Low NO	2 to 5 years	Annual
NO2	2 to 5 years	Annual
Low NO2	2 to 5 years	Annual
SO2	2 to 5 years	Annual
Low SO2	2 to 5 years	Annual
H2S	2 to 5 years	Annual
CxHy Hydrocarbon	2 to 3 years	Annual

Regularly recharge the battery to guarantee optimal operations of the electrochemical sensors. Do not leave the instrument an empty battery charge. Make sure the battery is always charged even during a long period of non use.

Replaced used sensor
Follow this procedure to replace a used sensor: The analyzer must be turned OFF

Remove the protective rubber holster.
Turn the analyzer on its back side.
Open the analyzer by removing 6 screws with cruciform (Philips) screwdriver. The back shell can then be lifted up.
Pull used sensor (1) up off the black manifold (3).
Remove black rubber cap (2) off used sensor and push cap onto new sensor.
Mount new sensor with rubber cap starting by connecting onto manifold’s pins (5) then make sure to properly align to 10 metal pins (6) into the mating black connector (4). Push sensor down to make sure connections are secure.

Sensors have very precise locations, see the following locations defined for each sensor

O2 sensor must be in O2 position
CO-H2 sensor must be in CO position
NO or low NO sensor must be in 6 position
NO2, SO2, low NO2, low SO2, CxHy and H2S sensors must be in 3, 4 or 5 position.
When a sensor has been replaced, it is possible to check the proper functioning of this new sensor by going in the “Information” menu of the analyzer. It is normal that a sensor that has just been installed gives the following message: “Current Error”, it is necessary to wait designated time to stabilize the polarization of the sensor.

Here are the minimum stabilization times for each sensor

O2: 1 hour
CO-H2: 8 hours
NO: 12 hours
Low NO: 12 hours
NO2: 8 hours
Low NO2:
SO2: 8 hours
Low SO2: 8 hours
H2S: 8 hours
CxHy: 8 hours

Replace filter inside the water trap
Follow this procedure to replace the filter inside the water trap:

Disconnect the smoke probe from the analyzer.
Turn the lower part (2) of the water trap to the left to detach it from the upper part (1).
Remove the part (3) by pulling it slightly.
Remove the used filter (4) and replace it by a new one.
Replace the part (3).
urn the lower part (2) of the water trap to the right to fix it on the upper part (1).
Make sure O-ring is seated properly in the lower part of water trap.

Replace the internal filter

The filter inside the analyzer is recommended be changed once a year.

Remove the protective rubber holster.
Turn the analyzer on its back side.
Open the analyzer by removing 6 screws with cruciform (Philips) screwdriver. The back shell can then be lifted up.
Remove the filter protection cover (1) by turning it to the left.
Remove the used filter (2).
Replace with a new filter following details shown below.
Reattach the filter protection cover and the analyzer’s back shell.
The bottom of the filter (4) is slightly wider than the top (3). The bottom of the filter (4) must be in contact with the filter holder 5).