VSYSTO F9B Baby Car Recorder User Manual

F9B Baby Car Recorder

User Manual

Safety Instructions

In order to use this product safely, please confirm that you fully understand the following.

WARNING: This section indicates that mishandling can have serious consequences.

Note: This section indicates that improper handling may cause injury to the user or damage the product.

WARNING

Please use this product under the premise of obeying traffic rules.
Do not install the device in a position that blocks the view or obstructs driving.
Do not disassemble or refit the product without permission
Do not use accessories other than the original ones
DVR main unit is NOT waterproof

ATTENTION

If the product makes an abnormal noise or smell, please stop using it immediately.
The camera module is IP67 waterproof but the host is NOT waterproof
When disposing of this product, please follow the classification principle and do not discard it at will.
Do not store this product in a high temperature and humid environment.
Pictures in this user manual for reference only, please in kind prevail.
Disclaimer: Tire pressure sensors may not fit all vehicle tires. Please consult your vehicle manual or a tire professional whether the tire pressure sensors are fit your car. If they affect your vehicle’s performance, driving, or insurance coverage, do not install it!
The manufacturer and distributor will not be responsible for damage due to improper installation and usage.

Standard Accessories

Main unit                                 Bracket

Front Camera                         Camera

Power module                             TPMS

Remote Control                   GPS Module

※If there is any change of specification and appearance due to improvement, we are not able to inform you in advance. Please understand.
※Please note that there are differences between the schematic diagram and the real object in the manual.

Packing List

After opening the package, please confirm whether the driving recorder is in good condition and the accessories are complete.

1)Main Unitx1                  2)Camera x2
3)Power Cable x1             4)TPMS x4
5)Bracket x1                     6)TF Card(Optional)x1
7)GPS Module x1             8)Wired Controller x1

Product Appearance Diagram

1. Type-C Interface
   (Can be connected to a computer and used as a USB flash drive)

2. TF Card Slot

3. Screw Hole

4. Bracket Hole

5. Display Screen

6. Power Cable Interface

7. Wire Controller Interface

8. Camera1 Interface

9. Camera 2 Interface

Product Connection Diagram

• With the advancement of technology, the product structure and parameters will continue to be improved. The pictures and texts in this book are for reference only. If there are pictures or descriptions that do not match the actual product, please refer to the actual display of the product.

Images Information and Menu Description

1. After selecting, press [OK] to enter Recording Mode.

2. The icon becomes larger to indicate that the function is selected.

3. Character description on the display in video mode

4. GPS

5. Microphone

6. Recording

7. Parking Monitoring

8. Atmospheric Pressure

9. Current Image

10. WiFi

11. Speed

12. Locked File

13. Video Time

14. Time Information

15. Temperature

16. Altitude

1. After selecting, press [OK] to enter Playback Mode.
2. The icon becomes larger to indicate that the function is selected.

Long press for 3 seconds in the Playback Mode to switch to the video files list of front ant rear camera

1. Press to select the video to playback

“F/”indicates front camera video playback

1. Front camera video files name identification: REC_The year, month and time of current video F.MOV

“R/”indicates rear camera video playback

2. Rear camera video files name identification: REC_The year, month and time of current video R.MOV

1. After selecting, press [OK] to enter Setting Mode.
2. The icon becomes larger to indicate that the function is selected.

1min/3min
5.Flameout detection| On:After detecting that the vehicle is turned off, the recorder shutdown after waiting for about 10 seconds; off:After 5 minutes without vibration, the recorder shutdown
6.Parking monitoring| Set whether to turn on or off parking monitoring function
7.Parking monitoring sensitivity| Set the sensitivity of parking monitoring
8.Timed recording after flameout| Set the time to keep recording after the vehicle is turned off
9.Date format| Three format options: YYYY MM DD/MM DD YYYY/DD MM YYYY
10.Clock setting| Set the recorder’s time
11.Time zone selection| Time zone selection around the world
12.Speed watermark| Whether it is necessary to turn on the driving speed display when playing videos
13.GPS Status| Display the current number of satellites, longitude, latitude, etc.
14.Unit system| Set the speed unit and temperature unit displayed when driving
15.Tire pressure function| Turn on/off
16.Tire pressure unit| 2 options of tire pressure value unit
17.Tire pressure alarm sound| Turn on/off
18.Tire pressure alarm threshold| Set the minimum or maximum value for the tire pressure alarm
19.Protection Level| G-Sensor sensitivity level adjustment
20.Button sound| Set the button sound on or off
21.Voice prompt| Set to turn on/off voice prompt
22.System reset| Restore to the factory default settings
23.WiFi Mode| Choose to turn WiFi on or off
24.Format SD card| Delete all files from the memory card
25.FW version| Information about the current software version of the recorder

1. After selecting, press [OK] to enter Language Choosing Mode.

2. The icon becomes larger to indicate that the function is selected.

3. Language identification — Corresponding to the selected language

4. The number of language choices depends on the actual model!

W5T Wired Controller Operating Instructions

• Function operation

1. Up Button:
   ①In the video recording interface, short press the up button once to switch to the full screen mode of the rear camera, which can be used as a backup camera. Then short press the up button once to return.
   ②In the video recording interface, long press the up button to enter the emergency video mode, and the front and rear cameras will capture a photo at the same time. The video file name of emergency recording is: KEY-XXXXXX.

2. OK Button:
   ①In the video recording interface, short press the OK button once to pause the recording, and then long press the OK button to enter the setting interface. You can use the up/down button to operate the settings required by the main unit. When the required functions are set, long press the OK key to return to the video recording interface.

3. Connect to main unit

4. Down Button:
   ①In the video recording interface and in the split screen mode of the front and rear cameras, short press the down button to switch to a single full front camera screen. Short press the down button again to switch to a single full rear camera screen. Then short press the down button again to return to the the split screen mode of the front and rear cameras.
   ※The software defaults to split screen images for front and rear cameras. When you select which display mode, the recorder will remember it. Next time you turn on the recorder, it will be the previous display mode you selected.

5. LED Blue Light:
   ①Blue light – Slow flashes – GPS is searching for satellites, the satellite icon in the upper left corner of the display is white.
   ②Blue light – Constant lights – GPS positioning is successful, and the satellite icon in the upper left corner of the display is green.

6. LED Red Light:
   Red light -Slow flashes- Camera is recording normally, the video file name is REC-XXXXXXX.
   Red light -Constant lights- Camera pauses recording.
   Red light -Fast flashes- Camera enters emergency recording mode, the video file name is GSR-XXXXXXX.
   ※If there are more than 10 videos named GSR-XXXXXXX in the TF card, the system will automatically delete the oldest video.
   Long press the up button in the recording state, the camera will record the emergency video. Video file name will be KEY-XXXXXXX.
   ※If there are more than 10 videos named KEY-XXXXXXX in the TF card, the system will automatically delete the oldest video.

• Recorder Video Playback Operation

In the video recording interface, long press the OK button once to switch to the setting interface. Use the up/down buttons to select the player icon. After selecting, short press the OK button once to enter the playback mode. Then select the video you want to play, and short press the OK button once to start the video. The default is the front camera video, long press the up button to switch to the rear camera video file.

ATTENTION
※There is a temperature sensor inside the wire controller. If the wire controller is operated, it is normal to find that the temperature of the recorder rises.
※The built-in temperature sensor has a deviation of 2 degrees Celsius.

Installation Diagram

1. Power Cable

2. Can be placed anywhere on the center console.

3. Waterproof Wired Controller
   Can be placed near the steering wheel.

4. Main Unit
   It can be installed on the window or center console where it does not block the driver’s view.

5. Waterproof Camera
   Can be placed anywhere on the center console.

6. Tire Pressure Monitoring Sensor
   Install it on the corresponding tire according to the letter on the tire pressure sensor, for example “F.L” means it needs to be installed on the left side of the front wheel.

Camera

Auxiliary Display Mode

1. Current speed while driving

①Long press the down button of the wire controller to enter the auxiliary display mode, and the driving speed is displayed on the first interface.

1. Tire pressure and temperature

②Short press the down button again to enter the tire pressure monitoring interface(optional)

1. Current Voltage
2. The voltage after flame out for one hour.
3. The voltage after flame out for one minute.

③Short press the down button again to enter the battery power display interface

1. Altitude
2. GPS Longitude
3. GPS Latitude
4. Atmospheric pressure

④Short press the down button again to enter the GPS information interface

1. Time of short time driving
2. Average speed of short-term

⑤Short press the down button again to enter the current mileage short-term memory interface

1. Current Time
2. Year Month Day
3. Current Week

⑥Short press the down button again to enter the year, month, and day interface

Mobile Phone APP Installation and Operation

WiFi APP is a mobile phone control software used with VSYSTO DVR device. This software is connected to the DVR device via Wi-Fi, it can directly preview and playback the video on the mobile phone, easily realize that viewing the camera documents on the screen of mobile phone, setting or other operations. Subverting the control method of traditional cameras, bring you a new experience.

App download for Android user

App download for Apple user

Scan the QR code above to download the latest APP from Google Play or APP Store. Or you can search “WiFi Camera” on Google Play or APP Store to download and install it.
Conditions of use and product association:

1. Smart terminal with Android 5.0 or higher or Apple terminal.
2. Purchase are cord erterminal device that uses VSYSTO design scheme, and connect the mobile phone WiFi to the camera correctly.

DVR WiFi Default Name: DV-F9B-XXXX
Default password: 1234567890

※To ensure the normal use of APP functions, please update the APP to the latest version in time.

• Synchronized Recorder Time

After the mobile phone is connected to the WiFi of the recorder, open the APP. When it prompts “command successful”, it means that the time of the recorder and the time of the mobile phone have been synchronized with the mobile phone (as shown in the figure below).

• Live Preview (Video / Photo)

After connect the camera WiFi with mobile phone, open the APP and click “Connect Device” to enter video preview status. In video preview state you can control camera to take video or photo. Click to switch front/rear image.
Click to full screen display(as shown in the figure below).

• Browse Recorder Files

Click browse the video files on recorder memory card(as shown in the figure below).

• Playback Recorder Files

Browsing the recorder file interface in the “Online” option, click the file you want to playback.
Click the upper left corner to switch the front/rear camera file, F means the front camera, L means the left camera, and R means the right camera.

• Download or Delete Recorder Files

In the “Online” browsing recorder file interface, click to select the file you want to download or delete, and then click “Save” or “Delete” below as needed (as shown in the figure below).

Video File Name
REC-XXXX— Normal recorded videos
GSR-XXXX— Emergency recorded videos

※The recorder will lock the last 20 emergency recorded videos (GSR-XXXX) that are not overwritten by the normal recorded videos. If there are more than 20 GSR-XXXX files, it will automatically overwrite the earliest locked emergency recorded videos.

• Local Files Management

Click to enter the browsing interface of local files to replay/delete the files stored in the mobile phone, and the operation is similar to the online interface.

• Recorder Parameter Setting

Click   to enter the recorder parameter setting interface, and you can set some parameters of the recorder in the mobile APP.
Set SSID is the WiFi name and password for setting the recorder (as shown in the picture below).

If you need to view the video track, you can save the downloaded video in the Local of APP. Then switch the phone to a network that can access the Internet, click to play the video, and thetrack of your driving will be displayed below the video. The default map of the APP is Baidu Map. If you need Google Map, please change Baidu Map to Google Map in the APP settings interface.

※When you play a video on the mobile APP to view the driving track, you can only view the video of a single camera (front/rear), and cannot play multiple cameras at the same time.

GVP Operation Guide (Optional)

Operating Systems Supported by GVPWinXP/7/8/10
Installed Version
Double-clicksetup.exe to start the installation. After the installation is complete, the desktop and start menu automatically generate shortcuts.

Double-click the desktop shortcut icon , or click the start menu to select the corresponding option of GVP to open the software.

Green Version

Double-click to open the software interface icon

Interface Picture Example

Initial Interface

When the mouse moves to the corresponding icon, there will be an operation prompt, please follow the prompt to operate (as shown in the figure below)

Interface during Playback

During playback, double-click the front camera or rear camera image, the full screen of the camera will be displayed. Double-click again to exit full screen.

Supports Multiple Languages and Google Maps
Click to set the player language and map

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>