VSYSTO M1 2K WiFi Dash Camera User Manual

VSYSTO M1 2K WiFi Dash Camera

WARNING

Please read this manual carefully, before using the device.

Warnings

• Do not use chemical cleaning agents.
• Use a soft cloth or lens cleaning kit to clean the dash­cam lens.
• Do not use paper napkins or towels. Avoid hits, drops and mechanical damage to the device.
• Do not use or store the device in too cold or hot places.
  • Storage temperature: -20°C to +60°C.
  • Operating temperature: +5°C to +40°C.
• Do not try to repair the dashcam by yourself.
• In case of any breakdowns, contact the dealer or ser­vice center.
• Neither the manufacturer nor the seller will be re­sponsible for any losses or missed opportunities due to the use of video footage and data obtained with the help of this dashcam.
• Technical specifications may be changed without prior notice to improve the quality of the product.

Important information

Attention

• Do not insert or remove the SD card when the device is on. This can lead to the DVR malfunction. Wait for 30 seconds after DVR shutdown, make sure that all the lights are off for at least 10 seconds, and only then safely remove the memory card.
• Set the correct time and date before using the device. The DVR may not record in case these settings were entered incorrectly.
• Use at least 0.5 seconds time interval while pressing control buttons, this guarantees proper functioning of the device.
• Do not turn off the power for at least 20 seconds after the power supply cable is connected. This is necessary to help the built-in battery function conrectly.
• If after you have started the car (when the power sup­ply cable is connected to the DVR), the device failed to switch to the recording mode automatically, simply un­plug the power supply cable for ten seconds and then try again.
• Use the restart option (by pressing «RESIT» button) in the following cases:
  • power indicator is not on when the power supply cable is connected;
  • the device does not switch from the standby to the recording or control mode;
  • the device fails to function properly.
• Files protected from overwriting by G-sensor are recorded in a loop with 8 files limit. When G-sensor is system wil automatically delete no earles one. neck basis to prevent dana ross this happens when the memors card is full).

PACKAGE CONTENTS

CONTROLS

1. Display
2. MENU button
3. REC/OK button
4. UP button
5. DOWN button
6. Status indicator
7. MiniUSB connector
8. Mounting hole
9. RESET button
10. Microphone
11. Speaker
12. Camera lens
13. Micro SD slot

Installation and connection

• Degrease the windshield surface before mounting.
• Make sure that the installation location is dry and clean.
• Do not attach the bracket at temperatures below +5°C.
• Prior to installation, position the dashcam accurately on the windshield. Use a felt-tipped pen to mark the mounting location, remove the protective layer from bracket and mount the dashcam to the pre-selected location.
• Insert the memory card into the dashcam. Pay attention to the correct installation. The memory card is inserted slots pins towards the display. The memory card should be put gently into the slot until it clicks.
• Connect the power cable to the dashcam.
• Connect the power unit to the car socket.

Description of device operation

Turn on and off

• Whenever power is connected to the dashcam, it turns on automatically and starts recording.
• After the power is turned off, it completes the record­ing and switches off You can turn the dashcam on or off manually by pressing and holding the REC/OK button on the device housing.

Quick setup using dashcam buttons
You can control the dashcam and quickly change some of its settings using buttons on the front panel.

• Use the REC/OK button to stop or start recording.
• By pressing the UP button during recording, you can turn sound recording on and off.
• By pressing the DOWN button during recording, the the recorder will capture a picture.

G sensor

The dashcam is equipped with a G sensor.
After the G sensor is tripped, the dashcam protects the current file from cyclic overwriting.

Description of device operation

You can adjust the G sensor sensitivity in dashcam set­tings or through a smartphone application.

Settings menu
Entering the settings menu of the dashcam is possible only with the camera recording off.
To enter the settings menu, stop the recording by press­ing the REC/OK button and then enter the menu by pressing the MENU button.

There are 4 items available in the menu:

• Recording mode
• View mode
• Settings
• Device language

Select the item you need with the UP DOWN and REC/OK buttons.

Settings menu

The following options are available in the Settings menu:

Press the MENU button to return to the items selection menu. To return to the recording mode, press the MENU button once more or select the recording mode item.

View mode

• You can enter the view mode by using the respective item in the settings menu.
• To move between files, use the UP DOWN buttons, press REC/OK to select a specific file.
• While watching a video, you can stop it by pressing the REC/OK button. You can also rewind the video sequence forward or backward using the UP and DOWN buttons.
• To exit the playback file or the playback mode and enter the recording mode, press the MENU button.

Mobile APP Installation and Operation Instruction

The WiFiAPP is a mobile control software used with VSYSTO camera equipment. This software connects to the camera device via Wi-Fi, can preview the playback video directly on the mobile phone, and easily realize the operation of viewing the files in the camera on the mobile phone screen and performing settings and other operations. It subverts the control mode of traditional cameras and brings you a whole new experience.

Download and Installation

Scan the QR code above to download the latest APP from Google Play and APP Store. Or you can search “WiFi Camera”on Google Play or APP Store to download and install it.

Conditions of use and product association

1. Smart terminal with Android 5.0 or higher or Apple terminal.
2. Purchase a recorder terminal device that uses VSYSTO design scheme, and connect the mobile phone WiFi to the camera correctly DVR WiFi .
   Default Name: VSYSTO-M1-XXXXX Default Password:1234567890 0To ensure the normal use of APP functions, please update the APP to the latest version in lime.

Synchronous recorder time
After connecting the phone to the camera WiFi, open the APP. When the APP prompts “Command succeeded”, it means that the recorder time has been synchronized with the phone time (as shown in the following figure).

Work with a mobile application

Setting up the dashcam through the application

• Using the application, you can also set up the dashcam.
• To enter the settings, first stop the recording by pressing the respective button under the video frame, then open the settings by pressing the settings button .
• In this menu, you can change and set some of the dash­cam settings.

Specification

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>