VSYSTO S2F 3 Inch IPS Screen WiFi Motorcycle Dash Cam User Manual

VSYSTO S2F 3 Inch IPS Screen WiFi Motorcycle Dash Cam

Specifications

• Model : S2F Dash Cam
• M a in Unit Dimensions : N/A
• Camera Dimensions : N/A
• Power Cable Length : N/A
• USB Test Cable Length: N/A
• Tie Quantity : 8
• Bracket Quantity : 1
• TF Card (Optional): 1
• GPS Module Quantity : 1
• Wire Controller Quantity : 1

Notes for Using the Dash Cam

• This product is an auxiliary (vehicle driving recorder) product for safe driving. Any loss caused by malfunction, information loss or using this product is irrelevant to our company.
• This product is an auxiliary device for recording external images of vehicles. Due to the different driving environment and vehicle environment, some functions will not support. The unscheduled firmware upgrade in order to improve the product will change the performance of the product, and sometimes the camera will cannot record due to the environment, so the driving images recorded in this product is for reference only. The state of TF card will also lead to camera cannot record.
• Although this product can record and save the videos of accidents, it does not guarantee that all the accident videos can be recorded. Slight collision accidents can’t start the collision sensor, so the video may not be recorded in the specialized folder.
• Be sure to disconnect the power supply when inserting or pulling out TF memory card.
• For the stable use of the product, it is recommended to format the TF card at least once a week.
• Generally TF card has a service life. Long-term use of TF card may cause the data to be unable to save. In this case, it is recommended to buy a new TF card to use. Our company will not be liable for data destruction caused by the long-term use of TF card.
• Please do not install or operate this product while driving.
• This device may disturb the function of improperly protected medical equipment. If you have any question or are uncertain whether the medical equipment can shield external RF energy, please consult your doctor or medical equipment manufacturer.
• Please do not make this product subject to strong impact or vibration, so as not to damage the product and cause malfunction or unavailable.
• Please do not use it in an environment with excessive dust density, so as to prevent cameras and other parts from being contaminated with dust, which will affect the video effect.
• Please stop using this product before cleaning and maintenance.
• Please do not use chemical solvents or detergents to clean this product.
• Please do not disassemble or modify this product without authorization.
• The ambient temperature range for the normal use of this device’s function is -20 to 65 degrees Celsius. Exceeding this temperature range may lead to product failure, fire or explosion.
• Please use it within the scope permitted by law.

The Packing List

• After opening the package, please confirm whether the driving recorder is in good condition and the accessories are complete.

1. Main Unit x1
2. Camera x2
3. Power Cable x1
4. USB Test Cable x1
5. Tie x8
6. Bracket x1
7. TF Car Optional） x1
8. GPS Module x1
9. Wire Controller x1

Product Appearance Diagram

Product Connection Diagram

• With the advancement of technology, the product structure and parameters will continue to be improved. The pictures and texts in this book are for reference only. If there are pictures or descriptions that do not match the actual product, please refer to the actual display of the product.

Images Information and Menu Description

1. After selecting, pass [OK] to enter Video Mode.

2. The icon becomes larger to indicate that the function is selected.

3. Character description on the display in video mode

4. After selecting, press [OK] to enter Playback Mode.

5. The icon becomes larger to indicate that the function is selected.

6. Press to select the video to playback ” indicates front camera video playback

• Long press for 3 seconds in the Playback Mode to switch to the video files list of front and rear camera

1. Front camera video files name identification: REC_ The year, month and time of current video F.MOV
2. Rear camera video files name identification: REC_ he year, month and time of current video R.MOV
3. After selecting, press[OK]to enter Setting Mode.
4. The icon becomes larger to indicate that the function is selected.

off after 1 min / 3min
5 . Parking monitoring| On / Off
6 . Parking monitoring sensitivity| Set the vibration sensitivity when parking
7 . Recording Time After Flameout| Set recording time after flameout(15 minutes / 30 minutes / 1 hour / 2 hours / 3 hours )
8 . Date format| YYYY MM DD / MM DD YYYY / DD MM YYY &
9 . Clock setting| Day Time
10 . Time zone selection| Time zone selection around the world
11 . Speed watermark| Whether it is necessary to turn on the driving speed display when playing videos on the computer .
12 . GPS Status| Display the current number of satellites , longitude , latitude and other information
13 . Unit system| Set the speed unit selection displayed when driving
14 . Rear camera mirror| Whether mirror selection is required for the rear camera display
15 . Protection Sensitivity| G – Sensor adjustment
16 . Button sound| On / Off
17 . Voice guide| On / Off
18 . Format SD card| Delete all videos from the memory card
19 . WIFI Mode| WIFI On / Off
20 . System reset| Restore to the factory default settings
21 . FW version| Information about the current software version of the machine

1. After selecting, press[OK]to enter Language Choosing Mode.

2.  The icon becomes larger to indicate that the function is selected.

3. Language identification — Corresponding to the selected language

4. The number of language choices depends on the actual model

W3 Wire Controller Operating Instructions

1. In the video recording interface, short press the up button once to switch to the full screen mode of the rear camera, which can be used as a backup camera. Then short press the up button once to return.
2. ln the video recording interface, long press the up button to turn off the recorder. After the motorcycle is powered off, the recorder will usually turn off after 5 minutes without vibration. If you don’t want to wait 5 minutes, you can long press the up button to quickly shut down.

OK Button

1. in the video recording interface, short press the OK button once to enter the emergency video mode, and the front and rear cameras will capture a photo at the same time. The emergency recording locked video filename is: KEY-XXXXX
   If there are more than 10 videos named KEY-XXXXXXX in the memory card, the system will automatically delete the oldest video.

2. In the video recording interface, long press the OK button to enter the setting interface. You can use the up/down button to operate the settings required by the main unit. When the required functions are set long press the OK button to return to the video recording interface.

Down Button

1. In the video recording interface and in the split screen mode of the front and rear cameras ,short press the down button to switch to a single full front camera screen. Short press the down button again to switch to a single full rear camera screen. Then short press the down button again to return to the front and rear camera split screens.
   The software defaults to split screen images for front and rear cameras. When you select which display mode, the recorder will remember it. Next time you turn on the recorder, it will be the previous display mode you selected.

2. In the video recording interface, long press the down button to enter the auxiliary mode, you can view Speed, Battery Power Display, Location, Short-term Memory, Date & Time.

LED Red Light

• Red light slow flashes – Camera is recording normally, the video file name is REC-XXXXXXX.
• Red light constant lights – Camera pauses recording. -Red light fast flashes
• Camera triggered the gravity sensor to record emergency vide, the video file names GSR_ХХХХХХХ
• If there are more than 10 videos named GSR-XXXXXXX in the memory card, the system will automatically delete the oldest video

Recorder Video Playback Operation

• In the video recording interface, long press the OK button once to switch to the setting interface. Use the up/down buttons to select the player icon. After selecting, short press the OK button once to enter the playback mode.Then select the video you want to play, and short press the OK button once to start  the video .The default is the front camera video, long press the up button to switch to the rear camera video file.

Auxiliary Display Mode

1. Long press the down button of the wire controller to enter the auxiliary display mode, and the battery power is displayed on the first interface.

2. Short press the down button again to enter driving speed interface.

3. Short press the down button again to enter short term memory interface.
   

4. Short press the down button again to enter GPS information interface.

5. Short press the down button again to enter the year, month, and day interface

Mobile Phone APP Installation and Operation

• Wi-Fi APP is a mobile phone control software used with VSYSTO DVR device. This software is connected to the DVR device via Wi-Fi, it can directly preview and playback the video on the mobile phone, easily realize that viewing the camera documents on the screen of mobile phone, setting or other operations. Subverting the control method of traditional cameras, bring you a new experience.

• App download for Android user

• App download for Apple user

Scan the corresponding QR code above and download the App.

Conditions of use and product association

1. Smart terminal with Android 5.0 or higher or Apple terminal.
2. Purchase a recorder terminal device that uses VSYSTO design scheme, and connect the mobile phone Wi-Fi to the camera correctly DVR WIFI Default Name: Moto DV _XXX Default password 1234567890

• To ensure the normal use of APP functions, please update the APP to the latest version in time.

Installation Guide

Shock Absorption Camera Bracket

1. Put the rubber shock absorption ring on the camera body.

2. Install the camera body on the bracket, and tighten the screws to fix it after adjusting the proper angle.

Cameras

• During installation, it is recommended to install the extension cable first, and then connect the main unit and camera separately (so that the installation is easier). If the distance between the main unit and the camera is less than 0.5 meters, it is recommended not to use the camera extension cable (please keep the camera extension cable for future needs).

• Viewing the screen or smart phone screen via Wi-Fi and adjust the bracket around to find a suitable horizontal view angle before fixed by double-sided foam tape
• Install the bracket downwards, tear off the double- sided tape and paste it in a suitable position （Adjust the position of the bracket to a satisfactory angle, and finally stabilize the cameras）
• The bracket is installed upwards, after tearing off the double-sided adhesive, it is recommended to screw on the lens to stabilize the cameras.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>