VSYSTO D6RL WiFi Motorcycle Dash Cam User Manual

VSYSTO D6RL WiFi Motorcycle Dash Cam

Preface

Welcome to use our products!

Before installing and using this product for the first time, please read this material carefully, which will help you make better use of this product.

If you fail to operate this product according to the explanation of the manual and the requirements of this manual or operate this product by mistake due to misunderstanding and other reasons, it will lead to data loss or other losses. Please keep the product and the manual properly, operate in strictly accordance with the manual and back up the data in time.

We have collated and checked this manual strictly and carefully, but we can’t guarantee that this manual is completely free of any errors and omissions. If you find anything, please contact our company.

The pictures in this manual are for reference only. If any picture is inconsistent with the actual display of the product, please refer to the actual display of the product.

In order to provide better services, we reserve the right to improve or modify the products and software programs described in this manual and the contents of this manual at any time without prior notice.
We are not responsible for the loss and loss of data and materials caused by misoperation of software and hardware, product maintenance or other conditions and are not responsible for other indirect losses caused thereby. Please back up your data and materials at any time.

If you find that the actual situation of this product is inconsistent with this manual during use, or you want the latest information or you have any questions or ideas, please contact our local distributor or online customer service.

I hope our products can meet your needs and serve you for a long time!

Matters Needing Attention in Using the Dash Cam

• This product is an auxiliary (vehicle driving recorder) product for safe driving. Any loss caused by malfunction, information loss or using this product is irrelevant to our company.
• This product is an auxiliary device for recording external images of vehicles. Due to the different driving environment and vehicle environment, some functions will not support. The unscheduled firmware upgrade in order to improve the product will change the performance of the product, and sometimes the camera will cannot record due to the environment, so the driving images recorded in this product is for reference only. The state of TF card will also lead to camera cannot record.
• Although this product can record and save the videos of accidents, it does not guarantee that all the accident videos can be recorded. Slight collision accidents can’t start the collision sensor, so the video may not be recorded in the specialized folder.
• Be sure to disconnect the power supply when inserting or pulling out TF memory card.
• For the safe of product stability, please format TF card at least once a week.
• General TF cards have a lifetime, Long-term use may cause data to be unsaved. In this case, it is recommended to buy a new TF card to use, and our company will not be liable for data destruction caused by long-term use.
• Please do not install or operate this product while driving.
• This device may disturb the function of improperly protected medical equipment. If you have any question or are uncertain whether the medical equipment can shield external RF energy, please consult your doctor or medical equipment manufacturer.
• Please do not make this product subject to strong impact or vibration, so as not to damage the product and cause malfunction or unavailable.
• Please do not use it in an environment with excessive dust density, so as to prevent cameras and other parts from being contaminated with dust, which will affect the video effect.
• Please stop using this product before cleaning and maintenance.
• Please do not use chemical solvents or detergents to clean this product.
• Please do not unauthorized disassemble or modify this product.
• The ambient temperature range for the normal use of this device’s function is -20 to 65 degrees Celsius. Exceeding this temperature range may lead to product malfunction, outbreak of fire or explosion.
• Please use it within the scope permitted by law.

Packing List

After opening the package, please confirm whether the recorder is in good condition and whether the accessories are complete.

1. Dash Cam Main Unit x1
2. Cameras x2
3. Power Cable x1
4. USB Test Cable X1
5. Bracket x1
6. TF Memory Card (Optional) x1
7. Wired Controller x1

Diagram of Product Appearance

Diagram of product connection

• The product structure and parameters will be continuously improved with the technological progress. The figure in this manual is only for reference. If there is a figure, and the description is inconsistent with the actual product, please refer to the actual display of the product.

Function Operation

Loop Recording Function

When the TF card is full, the old files recorded before will be deleted automatically in order. If there is an emergency file during recording, the file will not be deleted. The loop recording time can be set to 1/2/3/5 minutes.

G-sensor Trigger Lock File

After the sensitivity of G-sensor is on, when the device is recording, after the G-sensor triggers a collision and reaches the system preset level, the video will be locked to ensure that it will not be looped. The video file name is named GSR-XXXXXXXXXXX. When the TF card video file exceeds 10 “GSR” videos, the system will delete the earliest one.

Mobile Phone APP Installation and Operation Instructions

WiFi APP is a mobile phone control software used with Vsysto DVR device. This software is connected to the DVR device via Wi-Fi, it can directly preview and playback the video on the mobile phone, easily realize that viewing the camera documents on the screen of mobile phone, setting or other operations. Subverting the control method of traditional cameras, bring you a new experience.

App download for Android user

|

App download for Apple user

---|---

Scan the corresponding QR code above and download the App.
Conditions of use and product association:

1. Smart terminal with Android 5.0 or higher or Apple terminal.
2. Purchase a recorder terminal device that uses Vsysto design scheme, and connect the mobile phone WiFi to the camera correctly DVR WiFi Default Name: MotoDV_XXX
   Default password: 1234567890
   ※To ensure the normal use of APP functions, please update the APP to the latest version in time

Time of Synchronous DVR

After WiFi connection between the mobile phone and the DVR, open the APP, and the time of the mobile phone and the time of the DVR have been synchronized when “Instruction succeeded” prompted (as shown in the figure below)

Live Preview (video/photo)

After connecting the DVR WiFi with mobile phone, open the APP, click “Connect Device” to enter the video preview status. In the video preview status, it is feasible to control the DVR to record and take photo ( If there is a rear camera, Click to switch front and rear camera images)
Click to switch to full screen display (as the picture shown below).

Browse DVR Files

Click to browse files in the DVR memory card (see the figure as below)

Replay the DVR Files
Browsing the DVR file interface in the “Online” option, click the file which you want to replay. Click on the upper left to switch files of the front and rear camera , F represents the front camera and R represents the rear camera.

Download or Delete   DVR Files

Browsing the DVR file interface in the “Online” option, click to select the file which you want to download or delete and then click “Save” or “Delete” below as needed (see the figure as below)

Local Files Management

Click to enter the browsing interface of local files to replay/delete the files stored in the mobile phone, and the operation is similar to the online interface (see the figure as below)

DVR Parameter Setting

Click to enter parameter setting interface of the DVR to set some parameters of the DVR in the APP. Among them, you can set the WiFi name and password of the DVR in (as shown below)

Quick Installation Guide

Preliminary Test

1. Connect cam 1 & 2 to DVR host .
2. Find the special USB power cable and connecting to your power bank or USB adaptor to do a quick test before installation.
3. Prepare installation if everything looks good.
   ※Instructions of the matched 12V→5V power module
   Normal Version : Connect red wire to battery positive , black wire to battery negative , yellow wire to the 12V port controlled by key ignition (ACC port).
   Smart Version : The same connection with normal version but please waggle the power module (black box) around every 3 minutes to trigger the power supply , otherwise the electricity will be cut off automatically.

Quick Installation Guide

1. Locating the proper place to fix the front & rear camera, wired controller (optional), main unit (normally placed under the seat).
2. Planning the path of camera cable, wired controller cable, power cable before installation.
3. Fix and connect these parts by 3M tape, screws, cable ties on the proper place.
4.   ① Normal power module: Connect red wire to battery positive, black wire to battery negative, yellow wire to the 12V port controlled by key ignition (ACC port).
   ② Smart power module: The DVR will be turned on while engine start, the DVR will be turned off after engine stop.
   ※ Different motorcycle has different installation way, different DVR model has different cable connection definition (The diagram is for reference only) The position of the main unit and lens cable should be away from the high voltage circuit like xenon lamp, ignition plug etc.
   If your motorcycle is a traditional carburetor system please try to change a suitable R-value ignition plug when you meet the interference phenomenon.

Quick Adjustment

1. Release the lens cap, viewing the screen and rotate the lens body to adjust the horizontal view angle.
2. ① Normal power module: The DVR will be turned on/off while engine on/off.
   ② Smart power module : The DVR will be turned on while engine start;The DVR will be turned off after engine stop.

Accessories installation

Camera

The concave and convex bayonet of the joint shall be matched correctly

Please fix the camera with our standard extension cable before connecting to the DVR unless 0.5M is enough for you. Please keep the extension cable in case you will need it in someday

① Release the camera cap, rotate the bracket to suit the place where the camera fixed in.
② Slowly and lightly bend the bracket to adjust the vertical view angle

Adjust the bracket around to find a suitable  horizontal view angle before fixed by double-sided foam tape

Screws fixing is also recommended if the camera fixed downward

Battery Power Cable (optional)

Connect the red wire to battery anode, connect the black wire to battery cathode before connecting the “U” shape terminal cable to the power module in case of damaging the module by the unsteady voltage generated by fixing the “U” shape terminal

Fix the power module to a properly place of your motorcycle with the double- sided foam tape

ACC Power Cable (optional)

Connect the red wire to battery anode, Connect the black wire to battery cathode,connect the yellow wire to a 12V wire that is controlled by your key

Fix the wired controller to a properly place of your motorcycle with the double-sided foam tape

Wired Controller

Wired controller indicator light description:
Slow flash-normal video recording of DVR Quick flash-after pressing the wired controller, the emergency video will be started and the front and rear cameras will take a picture at the same time, and the indicator light will flash quickly. When the current emergency video is recorded, the wired controller will resume the slow flashing state.
Constant light-DVR is in standby state
Note: The files generated by the wired controller will be named with “KEY”.”KEY” video files recorded in emergency will not be overwritten by normal recorded video. But when the video files in the memory card exceed 10 KEY-XXXXXX videos, the system will automatically delete the oldest one.

Fix the wired controller to a properly place of your motorcycle with the double-sided foam tape

Troubleshooting

whether it can startup
② Please don’t insert the card, don’t connect the front and rear cameras, and see whether it can be turned on. If you can’t turn it on, please contact customer service.
No recording when startup| Please check whether the TF card is in good condition.
Please format the TF card, or replace the TF ca rd.
Recording Process| Image upside down| ① Please check whether the camera is installed upside down.
Water ripple| ② The picture flickers, water ripples. Please check whether the installation location is strong.
Cameras have
no image| Please swap the front and rear cameras to determine  whether it is a camera problem or a main unit problem.
Video blurred| Please check the camera for dirt and fingerprints;
Foggy| Before recording, please wipe the camera with the dust-free cloth.
Wrong recording time| ① Find the time and date option in the menu settings,  set the date and time manually, or connect to WIFI to enter the APP to update the time automatically.
② If the DVR has GPS, it will also update to the current time after GPS positioning. If the GPS update time is  different from the current time, please check the  settings menu to see whether the time zone option is  the local time zone.
The display is always on/ Rest screen| ① By default, the DVR will not operate after 1 minute,  and the screen will shut down automatically.
② If you want to keep the DVR’s display screen always light on. You need to find the “turn off screen  automatically” option in the menu setting interface and set it to off.
WIFI Connection Process| Can’t find WiFi| Please check whether WiFi is turned off. You can check  whether WiFi is turned off in the menu setting interface.
WiFi password is incorrect| Find the reset system in the settings interface to restore  factory settings. The default password is 1234567890
WiFi connection failed| After turning off the WIFI function of the mobile phone, turn on the WIFI function and connect to the WIFI again.
WIFI has been  connected to the APP, but there is no image,  or the command failed| For Android, please turn off WiFi helper and turn off 4G  network. Reconnect to WIFI.
Installation Process| Installation, wiring,
fixed cameras| ① Try to keep away the engine and high voltage package when installing the cameras cables.
② The front and rear cameras must be installed in a  strong location which has little vibration.
ACC power cable installation| The red wire is connected to the positive electrode of the battery, the black wire is connected to the negative electrode, and the yellow wire is connected to the ACC which is controlled by the key. The ACC position is generally below the lock. If you can’t find it, please go to the repair shop to install it.
GPS module installation| It is recommended to place the GPS module in an open location at the front or rear of the vehicle. Place the three letters which is on the GPS to wards the sky, and the installation position should not be close to cameras.
Wired controller installation| It is recommended to install it near the handle bar of the motorcycle to observe the video recording status of the DVR during driving conveniently and to operate the wired controller conveniently.

ATTENTION
Solutions for WiFi Connection Problem on Some Mobile Phones: Android :Firstly turn off your phone’s mobile data and then connect to DVR’s WiFi. If the prompt ”Trust this Network” appears, you must click “YES”, because Android phone forbids mobile data to ensure the recorded video file transferring speed from DVR to mobile phone.

IOS: Allows the mobile phone to continue to use the mobile network after connecting to the recorder via WIFI, but it affects the speed of downloading the DVR’s video files to the mobile phone.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>