EENOUR CH2244 Tumbler Heat Press 2 Station User Manual

June 14, 2024
EENOUR

Two Station Tumbler Mug Press
User Manual
EENOUR CH2244 Tumbler Heat Press 2
StationModel: CH2244

Please read this manual before use and follow its guidance.
Keep this manual for future reference.

INTRODUCTION

Thank you for purchasing the EENOUR Professional Two Station Tumbler Mug Press. Before use, please read the user manual of this product to ensure correct use after a complete understanding. After reading, please keep the user manual in a safe place for future reference. If you need any assistance, please contact our support team at: support@eenour.com with your product model number and Amazon order number.

SAFETY INSTRUCTIONS

  1. Don’t touch the tumbler heater as the machine is heating or still hot.
  2. Remember to turn off the machine after using it.
  3. This machine is not intended for use by children.

Notes:

  1. Check the voltage before using it.
  2. Do not heat the machine without a tumbler inside in case of burnout and reducing the life of the heater.
  3. If the machine works for more than 1.5 hours, it is better to turn it off for a 20-minute break.
  4. Use in a well-ventilated area — vapors from the heating process may irritate sensitive individuals.
  5. Plastic products cannot be heat pressed.
  6. Do not set the temperature any higher than 460°F, as it may cause overheating and stop working.
  7. Unplug the machine and allow it to cool completely before handling or storing.
  8. Do not clean the mug heating element with water.
  9. Use lubricating oil for regular machine connection maintenance.
  10. Keep the designed sublimation paper completely dry.
  11. Please take the sample to test. The sublimation temperature and time depend the subli- mation tumbler you purchased.

SPECIFICATIONS

Product Name CH2244 Two Station Tumbler Mug Press Voltage 110V
Temp. Range 0-482 °F (0-250°C) Power 1000W
Time Range 0-999 seconds Item Size 13.411.79.5 inch
Printable Size (Left Side) H: 10.6inch/27cm
D: 2.7-3.2inch/6.8-8.lcm Item Weight 20.91bs (9.5kg)
Printable Size (Right Side ) H: 10.6inch/27cm
D: 2.45-2.88inch/6.2-7.3cm Pack List 1 x Two Station 1 Tumbler Press Machine

1 x AC Power Cord
2 x Spare Fuse

Get to Know EENOUR CH2244 Tumbler Mug Press

EENOUR CH2244 Tumbler Heat Press 2 Station - overview

KNOW THE CONTROL PANEL

EENOUR CH2244 Tumbler Heat Press 2 Station - control
panel

How to Operate Control Panel

There are two control panels for the EENOUR CH2244 Professional 2 Station Tumbler Mug Press. The panel with the letter L is to control the left heater and the panel with the letter R is to control the right heater, and they work independently. The operation steps are the same, and you can operate two control panels at the same time.
1. How to switch between °F and °C?

  1. Long press the “SET” button for 3 scconds to “PV=Lo”, then press” ” to “SV=88”

  2. Short single press the “SET” button to “PV=CF” in the panel, then press the “ ” and “ ” buttons to switch between 1=°F and 0=°C.

  3. Long press the “SET” button for 3 seconds again to save the setting.

As shown above, the current temperature unit is °C. As shown above, the current temperature unit is °F. How to set printing time and temperature?

  1. Plug in power and press the power button(red), press the “SET” button once and “SP” shows on the screen, which means it’s in temperature setting mode. Press the ” ” and “ ” buttons to adjust the temperature.EENOUR CH2244 Tumbler Heat Press 2 Station - display 3
  2. Press the “SET” button again and “ST” shows on the screen, which means it’s in time setting mode. Press the ” “and ” ” buttons to adjust the counting time.EENOUR CH2244 Tumbler Heat Press 2 Station - display 4
  3. At Last, long press the “SET” button to save the settings and exit setting mode.
    Note: After buckling the handle, you need to press the countdown button, and then the countdown will start.

OPERATION STEPS GUIDE

The operation steps of the two stations are the same. The two heaters will not influence each other and they can work together. You need to set the temperature and countdown time for them individually. Follow the below operations to finish your DIY tumbler printing.
Part 1: Preparation Work

  1. Print the pattern on sublimation paper, or prepare the printed sublimation paper.
  2. Fix the image paper on a blank tumbler using thermal tape.EENOUR CH2244 Tumbler Heat Press 2 Station - Preparation work 2
  3. Put the tumbler into a proper heater.EENOUR CH2244 Tumbler Heat Press 2 Station - Preparation work 3
  4. Buckle the handle and turn two pressure knobs of the heater at the same time to adjust the pressure.EENOUR CH2244 Tumbler Heat Press 2 Station - Preparation work 4
  5. Push the bottom of the tumbler to make sure it does not move, in this case, the pressure is suitable.EENOUR CH2244 Tumbler Heat Press 2 Station - Preparation work 5
  6. Release the handle and take the tumbler out.EENOUR CH2244 Tumbler Heat Press 2 Station - Preparation work 6

Part 2: Steps to Print a Tumbler

  1. Connect the aviation connector of the heater.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 1
  2. Plug in power and press the power button.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 2
  3. Set printing temperature and countdown time (For temperature and countdown setting operation, please retum to p4; For the printing parameters, please move to p8).EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 3
  4. Wait until the machine heats up to the set temperature (Place a blank tumbler in, do not heat the machine without a tumbler inside).EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 4
  5. Wear protective gloves, put the tumbler into the heater, buckle the handle, and the machine starts countdown.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 5
  6. Press the countdown bution (green) of the heater and the countdown starts.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 6
  7. After the countdown is completed, release the handle and set a temperature and countdown time for another side.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 7
  8. Flip the tumbler 180° and buckle the handle, and press e countdown button 1o start.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 8
  9. After the countdown is completed, take out the tumbler and check the printing.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 9

Note:

  • Step 7 and Step 8 are not necessary for all tumblers pressing, you can find the best way for your tumblers.
  • Flip 180° heating to make sure another side heat enough, achieving a better printing.

HOW TO CHANGE THE HEATER?

  1. Tum off the machine, and unplug the aviation connectorEENOUR CH2244 Tumbler Heat Press 2 Station - assembly 11
  2. Unscrew the heater.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 12
  3. Take out the heater from the left or right side.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 13
  4. Put the new heater in, make sure all the screw holes coincide.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 14
  5. Fix the new heater with the screws in the amount it needs.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 15
  6. Insert the aviation connector.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 16

Note: Spared tumbler heater is not included.

HOW TO CHANGE THE FUSE?

  1. Tum off and unplug the power.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 17
  2. Pry off the fuse holder cover and take away.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 18
  3. Take out the old fuse and put in the new one (15A, 5x20mm).EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 19
  4. Close the fuse cover.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 20
  5. Make sure the fuse is installed tightly.EENOUR CH2244 Tumbler Heat Press 2 Station - assembly 21
  6. Plug in and turn on the powerEENOUR CH2244 Tumbler Heat Press 2 Station - assembly 22

PRINTING PARAMETERS

Material Machine Status Temperature Time
Straight stainless steel tumbler Cold(_140°F) 340°F-350°F 120s+50s
Hot( > 140°F) 356°F-365°F 50s+50s/90s+40s
Porcelain mug Cold(140°F) 374°F-392°F 300s
Hot( > 140°F) 374°F-392°F 200s
Glass tumbler Hot( > 140°F) 356°F-392°F 300s+200s/ 120s+120s

Note: The parameters above are for reference only. Please test to find the best parameters for your own tumblers.

TROUBLE SHOOTING

Fault Possible Causes Solutions
No display after powering up. Poor outlet contact or the fuse is blown. 1.

Check the power cable and check the outlet.
2. Make sure the heater attach-ment is connected.
3. Replace with the supplied backup fuse.
Fails to heat up or does not heat up to the temperature displayed. (±50°F available)| The mug heating attach- ment is burnt out.| 1. Check the heating attachment connections.
2. Replace the heating attach-ment.
Lack of color, faded image.| Because of the insufficient temperature and press time, the design is not tight or completely flat against the mug.| Adjust the temperature or increase the heating time. Make sure the design is firmly secured and flush against the mug. Adjust the temperature or increase the heating time.
Darkened, deep color, blurred image.| The temperature was too hot or pressed for a long time.| Set a lower temperature or time. Try more to get a suitable temperature and time for your mug.
The ink from the marker projects bleeds onto the mug heating element.| The transfer paper is too thin.| DO NOT clean with water that may cause a short circuit. You can wrap a mug with butcher paper to prevent transferring onto future projects or buy a new mug heating element to replace it.

WARRANTY

The product is with a 6-month warranty from the date of purchase (damages from normal wear and tear, alteration, misuse, neglect, accident, service by anyone other than the authorized service center, or act of God are not included).
During the warranty period and upon verification of defects, this product will be replaced or returned with proof of purchase.
Customer Support
If you need help regarding product issues, after-sales service, or other relevant problems, please contact us via email: support@eenour.com, and provide the following information:

  • Order ID
  • Problem description

E-mail: support@eenour.com
Website: www.eenour.com

MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals