EENOUR CH2244 Tumbler Mug Heat Press Machine User Manual

June 13, 2024
EENOUR

Two Station Tumbler Mug Press
User Manual
EENOUR CH2244 Tumbler Mug Heat Press
Machine

Model: CH2244
Please read this manual before use and follow its guidance.
Keep this manual for future reference.

INTRODUCTION

Thank you for purchasing the EENOUR Professional Two Station Tumbler Mug Press. Before use, please read the user manual of this product to ensure correct use after a complete understanding. After reading, please keep the user  manual in a safe place for future reference. If you need any assistance, please contact our support team at: support@eenour.com with your product model number and Amazon order number.

SAFETY INSTRUCTIONS

  1. Don’t touch the tumbler heater as the machine is heating or still hot.
  2. Remember to tum off the machine after using it.
  3. This machine is not intended for use by children.

Notes:

  1. Check the voltage before using it.
  2. Do not heat the machine without a tumbler inside in case of bum out and reducing the life of the heater.
  3. If the machine works for more than 1.5 hours, it is better to tum it off for a 20-minute break.
  4. Use in a well-ventilated area vapors from the heating process may irritate sensitive individuals.
  5.  Plastic products cannot be heat pressed.
  6. Unplug the machine and allow it to cool completely before handling or storing.
  7. Do not clean the mug heating element with water.
  8. Use lubricating oil for regular machine connection maintenance.
  9. Keep the designed sublimation paper completely dry.
  10. Please take the sample to test. The sublimation temperature and time depend the subli­mation tumbler you purchased.

SPECIFICATIONS

Product Name CH2244 Two Station Tumbler Mug Press Voltage 110V
Temp. Range 0-400°F (0-204°C) Power meow
Time Range 0-999 seconds Item Size 13.4.11.7.9.5 inch

Printable Size
(Left Side)| H: 10.6inch/27cm
D: 2.7-3.2inch/6.8-8.1cm| Item Weight| 20.9Ibs (9.5kg)
Printable Size (Right Side )| H: 10.6inch/27cm
D: 2.45-2.88inch/6.2-7.3cm| Pack List| 1 x Two Station Tumbler Press Machine
1 x AC Power Cord
2 x Spare Fuse

Get to Know EENOUR CH2244 Tumbler Mug Press

EENOUR CH2244 Tumbler Mug Heat Press Machine - Control

KNOW THE CONTROL PANEL

EENOUR CH2244 Tumbler Mug Heat Press Machine -
Control1

How to Operate Control Panel

There are two control panels for the EENOUR CH2244 Professional 2 Station Tumbler Mug Press. The panel with the letter L is to control the left heater and the panel with the letter R is to control the right heater, and they work independently. The operation steps are the same, and you can operate two control panels at the same time.

  1. How to switch between F and °C?

  2. Long press the “SET” button for 3 seconds to “PV=Lo”, then press”△ ” to “SV=88”

  3. Short single press the “SET” button to “PV=CF” in the panel, then press the “△” and “▽ ” buttons to switch between 1 =°F and 0=°C.

  4. Long press the “SET” button for 3 seconds again to save the setting.

EENOUR CH2244 Tumbler Mug Heat Press Machine -
Control2|
---|---
As shown above, the current temperature unit is °C.| As shown above, the current temperature unit is °F.

How to set printing time and temperature?

EENOUR CH2244 Tumbler Mug Heat Press Machine - Shown1

  1. Plug in power and press the power button(red), press the “SET” button once and “SP” shows on the screen, which means it’s in temperature setting mode. Press the “△ ” and ” ▽” buttons to adjust the temperature.EENOUR CH2244 Tumbler Mug Heat Press Machine - Shown2
  2. Press the “SET” button again and “ST” shows on the screen, which means it’s in time setting mode. Press the “△ ” and ” ▽ ” buttons to adjust the counting time.
  3. At Last, long press the “SET” button to save the settings and exit setting mode.
    Note: After buckling the handle, you need to press the countdown button, and then the countdown will start.

OPERATION STEPS GUIDE

The operation steps of the two stations are the same. The two heaters will not influence each other and they can work together. You need to set the temperature and countdown time for them individually. Follow the below operations to  finish your DIY tumbler printing.

Part 1: Preparation Work

EENOUR CH2244 Tumbler Mug Heat Press Machine - pattern

  1. Print the pattern on sublimation paper, or prepare the printed sublimation paper. EENOUR CH2244 Tumbler Mug Heat Press Machine - image
  2. Fix the image paper on a blank tumbler using thermal tape.EENOUR CH2244 Tumbler Mug Heat Press Machine - put
  3. Put the tumbler into a proper heater.EENOUR CH2244 Tumbler Mug Heat Press Machine - Buckle
  4. Buckle the handle and turn two pressure knobs of the heater at the same time to adjust the pressure.EENOUR CH2244 Tumbler Mug Heat Press Machine - push
  5. Push the bottom of the tumbler to make sure it does not move, in this case, the pressure is suitable.EENOUR CH2244 Tumbler Mug Heat Press Machine - handle
  6. Release the handle and take the tumbler out.

Part 2: Steps to Print a Tumbler

  1. Connect the aviation connector of the heater.
  2. Plug in power and press the power button.
  3. Set printing temperature and countdown time (For temperature and countdown setting operation, please return to p4; For the printing parameters, please move to p8).
  4. Wait until the machine heats up to the set temperature (Place a blank tumbler in, do not heat the machine without a tumbler inside).
  5. Wear protective gloves, put the tumbler into the heater, buckle the handle, and the machine starts countdown.
  6. Press the countdown button (green) of the heater and the countdown starts.
  7. After the countdown is completed, release the handle and set a temperature and countdown time for another side.
  8. Flip the tumbler 180° and buckle the handle, and press the countdown button to start.
  9. After the countdown is completed, take out the tumbler and check the printing.

Note:
Step 7 and Step 8 are for sublimation tumblers with a full pattern, and flipping 180° heating is to make sure all sides heat pressed and to get a perfect result.

HOW TO CHANGE THE HEATER?

  1. Turn off the machine, and unplug the aviation connector
  2. Unscrew the heater.
  3. Take out the heater from the left or right side.
  4. Put the new heater in, make sure all the screw holes coincide.
  5. Fix the new heater with the screws in the amount it needs.
  6. Insert the aviation connector.

Note:
Spare tumbler heating attachment is not included, which is available on the EENOUR Direct US store.

HOW TO CHANGE THE FUSE?

  1. Tum off and unplug the power.
  2. Pry off the fuse holder cover and take away.EENOUR CH2244 Tumbler Mug Heat Press Machine - old
  3. Take out the old fuse and put in the new one (15A, 5x20mm).
  4. Close the fuse cover.
  5. Make sure the fuse is installed tightly.
  6. Plug in and tum on the power

PRINTING PARAMETERS

Material Machine Status Temperature Time
Straight stainless steel tumbler Hot( > 140°F) 356°F-365°F 50s+50s/90s+40s
Porcelain mug 1lot( > 140°F) 374°F-392°F 200s
Glass tumbler Hot( > 140°F) 356°F-378°F 300s+200s/60s+60s

Note:
The parameters above are for reference only. Please test to find the best parameters for your own tumblers.

TROUBLE SHOOTING

Fault Possible Causes Solutions
No display after powering up. Poor outlet contact or the fuse is blown.

I.Check the power cable and check the outlet.
2.Make sure the heater attach-ment is connected.
3.Replace with the supplied backup fuse.
Fails to heat up or does not heat up to the  temperature displayed. (50°F available)| The mug heating attach- ment is burnt out.| 1.Check the heating attachment connections.
2.Replace the heating attach-ment.
Lack of color, faded image.| Because of the insufficient temperature and press time, the design is not tight or completely flat against the mug.| Make sure the design is firmly secured and flush against the mug. Adjust the temperature or increase the heating time.
Darkened, deep color, blurred image.| The temperature was too hot or pressed for a long time.| Set a lower temperature or time. Try more to get a suitable temperature and time for your mug.
The ink from the marker projects
bleeds onto the mug heating element.| The transfer paper is too thin.| DO NOT clean with water that may cause a short circuit. You can wrap a mug with butcher paper to prevent transferring onto future projects or buy a new mug heating element to replace it.
One pressure knob gets stuck.| The knobs on one side are not in the same line.| 1.Twist a knob to a line with the stuck one, and then both can be twisted easily.
2. Contact us on Amazon or by email for a detailed operation guide if it cannot be solved by yourself.

WARRANTY

The product is with a 6-month warranty from the date of purchase ( damages from normal wear and tear, alteration, misuse, neglect, accident, service by anyone other than the authorized service center, or act of God are not included).
During the warranty period and upon verification of defects, this product will be replaced or returned with proof of purchase.
Customer Support
If you need help regarding product issues, after-sales service, or other relevant problems, please contact us via email: support@eenour.com, and provide the following information:

MADE IN CHINA

Documents / Resources

| EENOUR CH2244 Tumbler Mug Heat Press Machine [pdf] User Manual
2244, CH2244, CH2244 Tumbler Mug Heat Press Machine, Tumbler Mug Heat Press Machine, Mug Heat Press Machine, Heat Press Machine, Press Machine, Machine
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals