EENOUR P5000 Portable Power Station User Manual

June 13, 2024
EENOUR

EENOUR-logo

EENOUR P5000 Portable Power Station

EENOUR-P5000-Portable-Power-Station-product.

  • Please read this user manual carefully before using the product to ensure you use it correctly.
  • To guarantee the safety of this product during transportation, it is only about 30% charged when it is packed.
  • So please charge it immediately after opening and before use.
  • Please avoid the use of extension cords or cable taps, as this product can be charged directly from wall sockets etc.
  • When using two or more sockets for charging, please avoid using any other products on the same socket.

DISCLAIMERS

  • Before using the product, please read the user manual carefully to ensure that you fully understand it before use. After reading, please keep the user’s manual in a safe place for future reference. If you use this product incorrectly, you may cause serious injury to yourself or others, as well as product damage and property damage.
  • Once you use this product, you can be deemed to have understood, recognized and accepted all the terms of this manual. Users under­take responsibility for their own actions and all the consequences that may arise therefrom.
  • EENOUR does not assume any responsibility for any loss caused by users’ failure to use the product in accordance with the User Guide. In order to comply with laws and regulations, EENOUR has the final interpretation of this document and all related documents of this prod­uct.

WHAT’S IN THE BOX

EENOUR-P5000-Portable-Power-Station-
fig-1

IMPORTANT SAFETY INSTRUCTIONS

Attention
Not permitted on aircraft.
WARNING – When using this product, basic precautions should always be followed, including the following:

  • Read all the instructions before using the product.
  • To reduce the risk of injury, close supervision is necessary when the product is used near children.
  • Do not put fingers or hands into the product.
  • Do not expose the product to rain or snow.
  • Use of an attachment not recommended or sold by the product man­ufacturer may result in a risk of fire, electric shock, or injury.
  • To reduce the risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting the product.
  • Do not use the product in excess of its output rating.
  • Do not use the product or attachment that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
  • Do not operate the product with a damaged cord, plug, or output cable.
  • Do not disassemble the product. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or electric shock.
  • Do not expose the product to fire or high temperatures.
  • To reduce the risk of electric shock, unplug the power pack from the outlet before attempting any instructed servicing.
  • Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the prod­uct is maintained.
  • When charging a device, the product may feel warm. This is a normal operating condition and should not be a cause for concern.
  • When charging the internal battery, work in a well-ventilated area and do not restrict ventilation in any way.
  • Do not clean the product with harmful chemicals or detergents.
  • Misuse, dropping, or excessive force may cause product damage.
  • When disposing of secondary cells or batteries, keep cells or batter­ies of different electrochemical systems separate from each other.
  • Do not use or store the power station in direct sunlight for a long period, such as in a car, cargo bed, or any other place where it will be exposed to high temperatures. Doing so may cause the product to malfunction, deteriorate, or generate heat. CAUTION: Risk of explo­sion if the battery is replaced by an incorrect type.
  • Disposal of a battery into a fire or hot oven, or mechanically crushing or cutting off a battery, can result in an explosion.
  • Leaving a battery in an extremely high-temperature environment can result in an explosion or leakage of flammable liquid or gas.
  • A battery subjected to extremely low air pressure may cause an explosion or leakage of flammable liquid or gas.
  • CAUTION: Risk of explosion if the battery is placed by an incorrect type.
  • Disposal of a battery into a fire or hot oven, or mechanically crushing or cutting off a battery, can result in an explosion.
  • Leaving a battery in an extremely high-temperature environment can result in an explosion or leakage of flammable liquid or gas.
  • A battery subjected to extremely low air pressure may cause an explosion or leakage of flammable liquid or gas.
  • Unplug the AC power cable to disconnect from the line voltage.

SPECIFICATIONS

Product Specifications

Product Name P5000 Portable Power Station
Product Size 21.6511.7719.17 in/ 5529.948.7cm
Product Weight 112.44 lb/ 51.0kg
Cell Capacity 5120Wh
AC Input 100 -120V/ 15A, 1800W Max
PV Input 12- 120V/ 15A, 1000W Max

AC Output

| ****

Rated 2200W, Peak 4000W, Pure Sine Wave, with Overcharge, Short Circuit Protection

USB QC 3.0| (5- 12V 18W) x2
USB| (5V 2.4A) x2
Type-C| 5-20V/5.0A, 100W max with PD 3.0 protocol
DC 5521| 12V/3Ax 2
4 Pin Aviation Socket| 24V/ 10A
Car Charger Output| 12V/ 10A
Charging Temperature| 32°F-104 °F/0-40°C
Discharging Temperature| 14°F-104°F/-10-40°C
Ambient Humidity| <90% RH
Cycle Life| >3500

Battery Specifications

Type LiFePO4 Battery
Single Battery Rated Voltage 3.2V
Rated Capacity of Single Battery 100Ah
Battery Pack Rated Voltage 51.2V
Single Cell Weight 2KG
Rated Capacity of Battery Pack 5120Wh

OVERVIEW

  • It is a portable power station, perfect for home emergency power backup and off-grid living.
  • It was built in LiFePO4 batteries, which supports AC fast charging, car charging, and solar panel charging. (It also has UPS function, which ensures continuous power, get non-stop power with a switcho­ver time of less than 1 Oms.)

Applications

  1. Outdoor: Car electronics: car refrigerator, car air pump, car vacuum cleaner, etc.; DIY power tools: blowers, lawn mowers, drills, electric saws; camping equipment: cameras, Drones, electric barbecue grills, LED lights, electric air mats.
  2. Indoors: Washing machines, TVs, radios, electric blankets, refriger­ators, kitchen appliances (cooking appliances), microwave ovens, cooking heaters, coffee makers, rice cookers, laptop computers, mobile phones, lighting equipment, etc.

The telescoping handle and wheels make it as easy to move around as a piece of luggageEENOUR-P5000-Portable-Power-Station-fig-2

  1. Power Switch
  2. 0ACSwitch
  3. DC Switch
  4. USB Switch
  5. LCD Screen
  6. Air Inlet/Outlet
  7. PV/ DC Input Port
  8. AC Fast/Slow Charging Switch
  9. AC Input Port
  10. Overload Protection
  11. Telescoping Handle Extension/ Retraction Button

Main Power Switch

  • Press the power button for 3S to switch it on, and press it again for 3S to turn it off.

NOTE:

  • Short press the switch will turn on/off the LCD display. If there is no operation for 30 minutes, the LCD display will be turned off and the power will be switched off automatically.

*AC Switch (AC outlet5, total output S2200W)**

  1. Press and hold the main power switch for 3 seconds to turn on the power station. Short press the AC button to switch the AC output ports on. Short-press it again to switch the AC output ports off.
  2. Check the remaining battery power. If the remaining battery level is less than 10%, please recharge the battery.
  3. Please check the operating voltage of the device to be connected.
  4. Make sure that the power consumption of the connected device is less than the rated power (2200W) of this unit.

Note:

  • When not in use, please turn off the AC output switch to save power.
  • The maximum AC output of the device that can be used is 2200W (Surge 4000W). Even if the total is less than 2200W, it may not be usable because the surge power is too high depending on the electri­cal equipment used.
  • For the 5 AC outlets, there are 1 for 30A and 4 for 20A. The 30A outlet has a rated output of 2200W, but the 20A outlet has a rated output of 2000W.
  • By pressing and holding the AC switch for 3 seconds or longer, you can switch between constant power mode and non-constant power mode (constant voltage mode).
  1. Constant Power Mode: When the load is over the rated 2200W but less than 3200W, it will reduce the working voltage of the load to operate the equipment with output up to 3200W.
  2. Non-constant power mode (constant voltage mode): Allows the device to operate at standard voltage. If the load exceeds the 2200W rating, the overload protection will cut off the output.

DC Switch

  1. Press and hold the main power switch for 3 seconds to turn on the power station. Short press the DC button to switch the DC output ports on. Short-press it again to switch the DC output ports off.
  2. Check the remaining battery power. If the remaining battery level is less than 10%, please recharge the battery.
  3. Connect the device to the DC cigarette lighter socket, DC output port, and the output side of the aviation socket.

Note:

When the DC output port is not in use, please turn off the DC output switch to save power.

USB Switch

  1. Press and hold the main power switch for 3 seconds to turn on the power station. Short press the USB button to switch the USB output ports on. Short-press it again to switch the USB output ports off.
  2. Check the remaining battery power. If the remaining battery level is less than 10%, please recharge the battery.
  3. Connect a USB device to the USB output port.

Note:

  • Quick charging (QC3.0, PD) may not be possible depending on the USB device being charged and the cable used for charging.
  • When not in use, please turn off the USB output switch to save power.

LCD Screen

  • Short press the main power button to switch the LCD ON/OFF. The LCD displays the power and status of the power station.

Cooling Air Inlet/Outlet

  • The cooling fan will run automatically when the product reaches a certain temperature during use. Please avoid blocking the cooling air inleUoutlet and do not place objects within 11.8 inches (30cm) of the cooling air inleUoutlet during the use of the product.
  • The fan has three gears, which are triggered according to the internal temperature. It will automatically run at low speed when the internal temperature reaches 113 °F(45°C) or higher.
  • It spins at medium speed when the internal temperature reaches 131 °
  • F (55°C) or higher.
  • It spins at high speed when the internal temperature reaches 149 °F (65°C) or higher.

PV/DC Input Port

  • Recharge this power station with a maximum solar input of 1 000W with a solar charging cable
  1. The maximum input voltage is 120V.
  2. If the PV/DC input port is charged with a voltage higher than 120V, the power station will be damaged. Which is not covered by the war­ranty.

AC Fast/Slow Charging Switch

  • The charging power can be adjusted through the AC charge speed switch on the back of the product.
  • Toggle this switch to the corresponding mode: fast charging or slow charging mode.
  • Slow charging: 600W Max Input
    • Fast charging: 1800W Max Input
  • When switching to the AC fast charging mode, you need to ensure that the output voltage of the power supply device meets 100-120V and the output current is greater than 15A.
  • The corresponding charging power is 1800W when the output voltage of power supply equipment is 120V and the output current is greater than 15A.

AC Recharging Port

  • Recharge your power station by connecting to a wall outlet with the AC charging cable. AC recharging (1800W Max)
  • Please ensure that the AC voltage and frequency of the device are consistent with the utility power before using the AC port for charging.

0verload Protection Button

  • In case of unstable power voltage supply due to lightning or other reasons, or if there is a large voltage input at the AC terminal, the over­load protection function (safety circuit breaker) will be activated to protect this product and disconnect the AC input port from external devices.
  • Please restore the AC input function of this product in the following order.
  1. Turn off the power button and unplug all ports devices.
  2. After confirming that there is no abnormality in each part, turn on the power button.
  3. Press the overload protection button and connect the AC cable to resume AC input.
  4. It is not recommended to use the voltage range beyond 100- 120V to charge the product, because it may cause damage to the power station, which is not covered by the warranty.

Telescoping Handle Extension/Retraction Button

Press this button to enable the extension/retraction of the telescoping handle.

LCD DISPLAY

EENOUR-P5000-Portable-Power-Station-
fig-6

1. Charge/Discharge Remaining Time 11. Cigarette Lighter (12V) Output
2. High Temperature Alert 12.DC( 12V) Output
3. Low Temperature Alert 13. Silent Mode
4. Fan Status 14. Constant Power Mode
5. Power Status 15. Fast Recharging Mode
6. UPS Mode 16. AC Recharging Mode
7. PV/Car Recharging Mode 17. Overload Warning
8. Total Input Power 18. USB Output
9. Total Output Power 19. PD Output
10. Aviation Socket (24V) Output 20. AC Output

UNINTERRUPTIBLE POWER SUPPLY (UPS)

To use the UPS feature, connect your power station to a wall outlet with the AC charging cable, then press the AC outlet button and con­nect your devices via the AC output portsEENOUR-P5000-Portable-Power-Station-
fig-7

  1. Once you turn on the electrical device, it makes use of grid AC power directly.
  2. When the utility power is cut off, it will automatically switch to the product’s internal battery power within 1 Oms.

Under UPS mode, the maximum AC output power is less than 1400W. If the AC output exceeds 1400W, the UPS icon will blink, which indicates an overcharge and the AC icon will be turned off, and the output is interrupted.

SOLAR PANEL RECHARGING

  • With a maximum solar input of 1 000W, fully charged at least 5.2 hours. ( Maximum input voltage 120V)
  • Solar panel charging power will be affected by the weather, climate and other conditions.
  • Solar panel voltage over 120V will damage the power station. Which is not covered by the warranty.
Solar Recharging

Option 1EENOUR-P5000-Portable-Power-Station-fig-8

Option 2EENOUR-P5000-Portable-Power-Station-fig-9

CAR RECHARGING

  • Recharge this power station by connecting to a car’s output port with the car charging cable.
  • Car recharging should be done after the car engine is started. Fail­ure to start the car engine may cause the car’s battery to run out of power.
  • Car recharging is usually low power of 90-240W, so the charging time is long ( 12V/8A or 24V/ 10A). If fast charging is required, wall outlet recharging is advised.EENOUR-P5000-Portable-Power-Station-fig-10

ESTIMATED USAGE TIME

  • 5120Wh x DOD x ri + (load W) = estimated usage time (unit: h)

Note:

  • DOD is the depth of discharge of the battery, and ri is the conversion rate of the inverter.
  • DOD= 90%, ri = 90%, load W = power consumption (wattage) of your device.
  • For reference, assuming the power consumption of your device is 1 000W, the working time will be 5120Wh0.90.9/1 000W=4.14hrs (roughly calculated).
  • Please note that there is also an electrical loss due to self-discharge when the output port is turned on. The specific electrical loss is AC: 20W, DC24V: 2W, DC12V: 1W, USB: 0.5W.

TROUBLESHOOTING

EENOUR-P5000-Portable-Power-Station-
fig-11

FAQ

  1. The electrical appliance power is within the rated output power range of the product but it cannot be used.
    • The battery of the power station is low and needs to be recharged. When some electrical appliances start, the peak power is higher than the product power, or the nominal power of the electrical appli­ance is greater than the electrical appliance power.
  2. Why is there a noise when using it?
    • The noise comes from the fan or the relay when you start or use it.
  3. Is it normal for the charging cable to heat up during use?
    • Yes, it is. The charge cable complies with national safety standards and has passed the certification.
  4. What devices the product can support the AC output?
    • The AC output is rated 2200W. It’s available to power most home appliances, whose rated power is lower than 2200W. Please make sure the total loading by AC is under 2200W before use.
  5. How can we know the remaining discharge time?
    • Please check the data on the LCD screen, it will show the remaining discharge time when you turn it on.
  6. How can we confirm the product is charging?
    • When the product is undercharging, the product screen will show the input wattage and the power percentage indicator will blink.
  7. How should we clean the product?
    • Please use a dry, soft, clean cloth or tissue to wipe the product.
  8. How to store?
  • Please turn off the product and place it in a dry environment. Do not place this product near water.
  • For long-term storage, we recommend using the product every three months(Run out the remaining power first and recharge it to the percentage you want, such as 50% ).

MAINTENANCE

  1. It is recommended to use or store this product in an environment of 68 ° F (20° C) to 36 ° F (30° C) and keep it away from water, heat, and other metal objects.
  2. For safety reasons, please do not store this product in an environment higher than 113 ° F (45° C) or lower than 14 ° F (- 10° C) for a long time.
  3. If it is not used for a long time, please charge it to 60% before stor­ing. If the battery is left unused for a long time when the battery is seriously insufficient, it will cause irreversible damage to the battery and shorten the cycle life of the product.

Warranty

  • The product comes with a 1-year warranty from the date of purchase (dam­ages from normal wear and tear, alteration, misuse, neglect, accident, service by anyone other than the authorized service center, or act of God are not included).
  • During the warranty period and upon verification of defects, this product will be replaced when returned with proof of purchase.

CUSTOMER SUPPORT

If you need help regarding product issues, after-sales service, or other relevant problems, please contact us via email: at support@eenour.com, and provide the following information:

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals