Laserliner 081.180A SuperPlane Laser 3D Cross Line Laser Instruction Manual

: June 4, 2024
: Laserliner

Table of Contents

Laserliner 081.180A SuperPlane Laser 3D Cross Line Laser
General safety instructions
Safety instructions
Special product features
Number and direction of the lasers
Inserting the batteries
Overview
Horizontal and vertical leveling
Hand receiver mode
Slope mode
Information on maintenance and care
EU directives and disposal
SERVICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Laserliner 081.180A SuperPlane Laser 3D Cross Line Laser

Completely read through the operating instructions, the „Warranty and Additional Information“ booklet as well as the latest information under the internet link at the end of these instructions. Follow the instructions they contain. This document must be kept in a safe place and if the laser device is passed on, this document must be passed on with it.

Three-dimensional laser with horizontal and two vertical 360° laser circles and slope function for aligning tiles, wall studding, windows, doors, etc.

General safety instructions

The device must only be used in accordance with its intended purpose and within the scope of the specifications.
The measuring tools and accessories are not toys. Keep out of reach of children.
Modifications or changes to the device are not permitted, this will otherwise invalidate the approval and safety specifications.
Do not expose the device to mechanical stress, extreme temperatures, moisture or significant vibration.
The device must no longer be used if one or more of its functions fail or the battery charge is weak.

Safety instructions

Using class 2 lasers

Attention: Do not look into the direct or reflected beam.

Do not point the laser beam towards persons.
If a person‘s eyes are exposed to class 2 laser radiation, they should shut their eyes and immediately move away from the beam.
Under no circumstances should optical instruments (magnifying glass, microscope, binoculars) be used to look at the laser beam or reflections.
Do not use the laser at eye level (1.40…1.90 m)
Reflective, specular or shiny surfaces must be covered whilst laser devices are in operation.
In public areas shield off the laser beam with barriers and partitions wherever possible and identify the laser area with warning signs. Dealing with electromagnetic radiation
The measuring device complies with electromagnetic compatibility regulations and limits in accordance with the EMC Directive 2014/30/EU.
Local operating restrictions – for example, in hospitals, aircraft, petrol stations or in the vicinity of people with pacemakers – may apply. Electronic devices can potentially cause hazards or interference or be subject to hazards or interference.

Special product features

Automatic alignment of the device with a magnetically dampened pendulum system. The device is brought into the initial position and aligns itself autonomously.
Transport LOCK: The device is protected with a pendulum lock during transport.
Laser diodes of the highest performance class produce extremely bright laser lines. They remain visible even on surfaces at great distances or on dark surfaces and under bright ambient light conditions.
RX-READY technology enables line lasers to be used even in unfavorable light conditions.The laser lines pulsate at a high frequency and this can be picked up by special laser receivers over long distances.

Number and direction of the lasers

H: horizontal laser
V: vertical laser
S: slope function

Inserting the batteries

Open the battery compartment (3) and insert the batteries in accordance with the installation symbols, ensuring the correct polarity.

Overview

Laser emitting window
Slide switch
- ON
- OFF / Slope mode
Transport lock
Battery compartment (bottom)
1/4″ tripod threads (bottom)
Laser line selection button / Slope mode on / Hand receiver mode on / off

When transporting always switch off all lasers, secure the pendulum and set the slide switch to “OFF”!

Low battery indicator: All laser lines flash for 3 seconds and then go out when the battery charge is low.

Horizontal and vertical leveling

Release the transport restraint, and set slide switch (2) to “ON”. The horizontal laser line appears. The laser lines can be switched individually with the selection button.

Warning: The transport restraint must be released for horizontal and vertical leveling. The laser lines flash when the device is outside the automatic leveling range of 3°. Position the device such that it is within the leveling range.

Hand receiver mode

Optional: Working with the laser receiver RX

Use an RX laser receiver (optional) to carry out leveling at great distances or when the laser lines are no longer visible. To work with a laser receiver, switch the line laser to hand-held receiver mode by keeping button 5 (handheld receiver mode on / off) pressed. The laser lines will now pulsate with high frequency, making the laser lines darker. The laser receiver can detect these pulsating laser lines.

warning

Observe the laser receiver‘s operating instructions for line lasers.
Due to the special optics required to generate a continuous 360° laser line, the underlying technology may cause differences in brightness in different areas of the line.
This may lead to different ranges in hand receiver mode.

Slope mode

Do not release the transport restraint, set slide switch (2) to “OFF” and switch on slope mode by pressing and holding (3 seconds) button 5. Select the laser with the selector button (5). Sloping planes and tilts can now be measured. In this mode, the laser lines no longer align automatically. This is signalized by the laser lines flashing.

Preparing the calibration check

It is possible for you to check the calibration of the laser. To do this, position the device midway between 2 walls, which must be at least 5 meters apart. Do this by turning the unit on, thus releasing the transport restraint (cross laser on). Please use a tripod.

Mark point A1 on the wall.
Turn the device through 180° and mark point A2. You now have a horizontal reference between points A1 and A2.

Performing the calibration check

Position the device as near as possible to the wall at the height of point A1.
Turn the device through 180° and mark point A3. The difference between points A2 and A3 is the tolerance.

When A2 and A3 are more than 0.35 mm / m apart, an adjustment is necessary. Contact your authorized dealer or else the UMAREX-LASER LINER Service Department.

Checking the vertical line

Position the device about 5 m from a wall. Fix a plumb bob with a line of 2.5 m length on the wall, making sure that the bob can swing freely. Switch on the device and align the vertical laser to the plumb line. The precision is within the specified tolerance if the deviation between the laser line and the plumb line is not greater than ± 1.75 mm.

Checking the horizontal line

Position the device about 5 m from a wall and switch on the cross laser. Mark point B on the wall. Turn the laser cross approx. 2.5 m to the right and mark point C. Check whether the horizontal line from point C is level with point B to within ± 1.75 mm. Repeat the process by turning the laser to the left.

Regularly check the adjustment before use, after transport and after extended periods of storage.

Information on maintenance and care

Clean all components with a damp cloth and do not use cleaning agents, scouring agents, and solvents. Remove the battery(ies) before storing it for longer periods. Store the device in a clean and dry place.

Technical data (Subject to technical alterations. 21W25)

Self-levelling range| ± 3°
Precision| ± 0.35 mm / m
Operating range| (depending on room illumination) 15 m
Working range with hand receiver| (depends on how the technology affects the difference in brightness) 40 m
Laser wavelength| 650 nm
Laser class| 2 / < 1 mW (EN 60825-1:2014/AC:2017)
Power supply| 4 x 1.5 V alkaline batteries (type AA) / rechargeable batteries
Operating time with 3 laser levels with 2 laser levels

with 1 laser level

| approx. 6 hours

approx. 10 hours

approx. 25 hours

Operating conditions| 0 … 50°C, 80% rH, no condensation, max. altitude 4000 m
Storage conditions| -10°C … 70°C, 80% rH, no condensation
Weight| 650 g (incl. batteries)
Dimensions (W x H x D)| 85 x 125 x 130 mm

EU directives and disposal

This device complies with all necessary standards for the free movement of goods within the EU. This product is an electric device and must be collected separately for disposal according to the European Directive on waste electrical and electronic equipment.

Further safety and supplementary notices at: http://laserliner.com/info?an=AFM