Cumbor CB418 Extra Wide Baby Safety Gate User Guide

Cumbor CB418 Extra Wide Baby Safety Gate

IMPORTANT! KEEP FOR FUTURE REFERENCE

WARNING

• To prevent serious injury or death, securely install gate or enclosure and use according to manufacturer’s instructions.
• Never use with a child able to dimb over or dislodge the gate or enclosure.
• This product will not necessarily prevent all accidents.
• Never leave child unattended.
• Use only with the locking mechanism securely engaged.
• Intended for use with children from6 months through 24 months of age.
• Stop using gate if any parts are missing or become damaged.
• Periodically check all fasteners to be sure they are tight and secure.
• Adult Assembly Required.
• The surfaces that the gate is to fixed to must be suitable for the purpose and must be structurally sound.
• Indoor use only, is not to be exposed to outdoor elements.
• Install this gate away from heaters and other sources of heat.
• Children have died or been seriously injured when gates are not securely installed.
• ALWAYS install and use gates as directed using all required parts.
• You MUST install wall cups to keep gate in place. Without wall cups,child can push out and escape.
• NEVER use to keep child away from pool.
• Gates that must be installed at least 4inch from the first step of the stair.

components

• A  Main Gate  x1
• B  Extension x1
• C  Extension x1
• D  Extension x1
• E  Tension Bolt x4
• F Wall cup xl  x4
• G Position plate x1
• H  Wrench Dry Wall Anchor   x1
• G  Screw   x1
• H  Sticky Pad  x1

INSTALLATION GUIDE

• METHOD A : (follow STEP1→2 >3 >4 >5 >6)

• METHOD В: (follow STEP1→2→2.1→2.2 >3 >4 >5 >6

• If mounting the gate at the top of the stairs please follow method

• B NEVER use at the top of stairs without fixing wall cups to the wall.

TIP: If you need to place in a doorway that has baseboards, ensure that both the top and bottom measurements are considered

Add extensions as needed.

If mounting the gate at the top of the stairs, please follow steps 2.1 and 2.2.Otherwise, you can skip to step 3.

• Place the position plates on where you want to install the gate. (This is where you will attach the wall cups.) Make sure the plates are centered within your doorway/opening and MARK the position on the wall.
• Use the wall anchors and the screws to attach the wall cups to the wall, based on your markings.
• • Insert the bolts into all (4) corners of the gate/extension.
• Hold the rubber base while. Twist the adjustment wheels with your hands or the wrench.
• Make sure the upper and lower latches lock securely
• Make sure that the upper and lower distances are consistent.

TIP: Suitable clearance of the door gap is 1/16″. The gap between the gate and wall should never exceed 2.4″.

Cut off the belt and test the door gate:

1. Open and close the gate repeatedly to check the smoothness.
2. Push the gate and frame to check stability

Opening Method: Press the button and ift the gate panel UP to open.

TROUBLESHOOTING

If the gate does not open or engage properly:

• The gate is over-tightened or not tight enough. Suitable clearance of the door gap is 1/16″.(Please refer to step 5)
• The latches are not level. Solution: Adjust the tension bolts on each side of the door until it is centered and level, with equal distance between the gate and wall on both sides, top and bottom.

• C. Gate is not properly aligned onto the door frame. Solution : Adjust the gate by loosening all tension bolts and reposition gate. Make sure the gate is properly aligned onto the door frame/door opening, then re-tighten tension bolts.
• If you have cut the belt by accident or need to reinstall the gate elsewhere in the future:
  • Solution : Use another rope/belt to tie the guardrail before removing, otherwise you may need the assistance of others to help you install it.
• If you need to place it in a doorway that has baseboards:
  • Solution: it will fit securely. Each of the four corners has an adjustable mount that can be tightened to varying distances. Important Advice: Measure the width and ensure that both the top and bottom measurements are considered.
• If the gate becomes loose on the wall:
  • Solution: Check if the bolts are properly tightened. (Please refer to step 5)

MAINTENANCE

• Clean by using a sponge with warm water or mild detergent. DO NOT use abrasive cleaners or bleach.
• Check the gate regularly to ensure all hardware and mounts are securely tightened.
• DO NOT use if any component is damaged or missing.

Scan the QR code above or search our official account Cumbor Family on YouTube for more detail instruction.

Manufacturer Support: 1-888-281-8150 (24/7)

• * [support@aborderproducts.com](mailto:support@aborderproducts.com)(24/7) 30

  • Days Free Return & Replacement
  • 2-Year Product Warranty
• Have a question for the seller?

1. Find your order
2.  Click “View order details” ****
3. Click the “Seller name”
4. Click “Ask a question”

• Gifted parts, replacements, consumable products are not covered by the 2-year warranty. Manufacturers’ warranties may not apply in all cases, depending on factors such as use of the product, where the product was purchased, or who you purchased the product from. Please review the warranty carefully, and contact the manufacturer if you have any questions.

Documents / Resources

| Cumbor CB418 Extra Wide Baby Safety Gate [pdf] User Guide
CB418 Extra Wide Baby Safety Gate, CB418, Extra Wide Baby Safety Gate, Baby Safety Gate, Safety Gate, Gate
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>