Kwikset 914 Contemporary Keypad SmartCode Electronic Deadbolt Smart Lock Instruction Manual

Kwikset 914 Contemporary Keypad SmartCode Electronic Deadbolt Smart Lock

Product Information

Specifications:

• Model: 61037-005 Rev 05 ZigBee
• Required Tools: Ruler, Phillips head screwdriver
• Manufacturer: Kwikset
• Contact Information: 1-866-863-6584, www.kwikset.com

Parts List:

• Latch A
• Exterior Assembly
• Interior Assembly
• Latch B (not included, contact Kwikset to order)
• Latch/Strike Adapter Ring
• Mounting Plate
• Strike 03809
• Batteries Keys 46780
• Lock SmartKey Tool 69316
• Lock Bag 48654

Installation and User Guide

If you will be using a smart home app with your lock, download the app and set up your controller or hub before proceeding further  with lock installation.

Prepare the Door and Check the Dimensions:

1. Make sure your door is compatible. If you have a standard deadbolt mounted separately from the handle below it, your door is compatible.
   • Compatible: Standard deadbolt mounted separately from the handle.
   • Not Compatible: Rim Lock, Mortise Lock, Integrated Interior.
2. Remove your existing deadbolt from your door.
3. Measure to confirm that the hole in the door is either 2-1/8  (54 mm) or 1-1/2 (38 mm).
4. Measure to confirm that the backset is either 2-3/8 or 2-3/4 (60 or 70 mm).
5. Measure to confirm that the hole in the door edge is 1 (25 mm).
6. Measure to confirm that the door is between 1-3/8 and 2 (35 mm and 51 mm) thick.

Install the Latch and Strike:

1. Extend the latch bolt.
2. Hold the latch in front of the door hole, with the latch face flush against the door edge.
3. Check if the D-shaped hole is centered in the door hole. If not, rotate the latch face to extend the latch.
4. Install the latch using provided screws.
5. Install the strike on the door frame, ensuring the hole is drilled at least 1 (25 mm) deep.

Install the Exterior Keypad:

1. Determine the diameter of the hole in the door (2-1/8 or 1-1/2 inches).
2. If the diameter is 1-1/2 inches, install the Adapter Ring on  the Exterior Assembly. Otherwise, discard the Adapter Ring.
3. Install the exterior keypad and mounting plate using provided screws.
   • Support the exterior assembly during mounting plate installation.
   • Route the cable underneath the latch and through the center hole, then push it into the bottom hole.
   • Tighten screws evenly, avoiding over-tightening.

FAQ:

• Q: What tools do I need for installation?
  A: You will need a ruler and a Phillips head screwdriver.

• Q: How can I order a drive-in latch if Latch B is not included?
  A: Please contact Kwikset at 1-866-863-6584 to order a drive-in latch for your lock.

• Q: Where can I find complete door drilling instructions?
  A: Complete door drilling instructions are available at www.kwikset.com/doorprep.

• Q: What should I do if my door is not compatible?
  A: If your door is not compatible (Rim Lock, Mortise Lock, or Integrated Interior), the lock cannot be installed.

• Q: How do I adjust the latch if the D-shaped hole is not centered?
  A: Rotate the latch face to extend the latch until the D-shaped  hole is centered in the door hole.

• Q: What should I do if the holes are worn out?
  A: Use longer screws provided in the Latch/Strike Bag if the holes are worn out. You will have two extra screws.

• Q: How deep should the hole in the door frame be for installing  the strike?
  A: The hole in the door frame should be drilled a minimum of 1 (25 mm) deep.

• Q: How should I route the cable during installation?
  A: Route the cable underneath the latch and through the center hole, then push it into the bottom hole.

Required tools

Kwikset 1-866-863-6584 www.kwikset.com

Parts List

Begin with your smart home app

If you will be using a smart home app with your lock, download the app and set up your controller or hub before proceeding further with lock installation

Prepare the door and check dimensions

If drilling a new door, use the supplied template and the complete door drilling instructions available at kwikset.com/doorprep

• Make sure your door is compatible. If you have a standard deadbolt mounted separately from the handle below it, your door is compatible.

• Remove your existing deadbolt from your door

• Measure to confirm that the hole in the door is either 2-1/8″ (54 mm) or 1-1/2″ (38 mm).
  Note: Additional door preparation may be required for doors with 1-1/2″ (38 mm) holes. Consult the deadbolt drilling instructions at kwikset.com/doorprep

• Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70 mm).

• Measure to confirm that the hole in the door edge is 1″ (25 mm).

• Measure to confirm that the door is between 1-3/8″ and 2″ (35 mm and 51 mm) thick

Install the latch and strike

• Extend the latch bolt.
• Hold the latch in front of the door hole, with the latch face flush against the door edge.
• Is the D-shaped hole centered in the door hole?
• Install the latch.
• Install the strike on the door frame.
  Make sure the hole in the door frame is drilled a minimum of 1″ (25 mm) deep

Install the exterior keypad

• What is the diameter of the hole in the door?
• Locate the screws for step 4C and keep them within reach.
• Install the exterior keypad and mounting plate.

Install the interior assembly

• Remove the interior cover and battery pack from the interior assembly
• Install the interior assembly onto the mounting plate.

Install the batteries and perform the door handing process

This step will teach your lock the orientation of your door and is crucial to lock operation.

• Install 4 AA batteries in the battery pack.

• With the door open, press and HOLD the “Lock” button while installing the battery pack.
  Hold the button until the latch bolt starts moving on its own.

• The latch will retract and extend to learn the orientation of the door.

• The Status LED will indicate success or failure.

Pair the lock with your smart home system

• Initiate the pairing process through your smart home system (either through your smart home app, at your panel, or at your controller or hub).
  Refer to your smart home system instructions for more information.

• You may be prompted by your smart home system to scan the QR code on the interior assembly. If not, proceed to step C.

• When prompted by your smart home system to initiate pairing at the lock, press button “A” on the lock interior four times.

• If the pairing process is successful, re-name  the lock in your system (if applicable).
  If the pairing process is unsuccessful, press button “B” nine times.
  Perform steps 7A-7D again.
  If still unsuccessful, follow your smart home system’s instructions to remove (exclude/unpair) the lock from any other network. Then perform steps 7A-7D again.

Add user codes

(30 maximum)

It is recommended that you add and delete all user codes through your smart home system.
If your system does not allow this, codes may be added directly to the lock as shown here.

• Programming information
  • Mastercode: For enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the SmartCode 914 Programming and Troubleshooting Guide at www.kwikset.com.
  • Programming Timeout: During programming, if no button is pressed for five seconds, the system will time out (indicated by three beeps and a red flashing keypad), and you will need to restart the procedure.
• Make sure the door is open. Press the “Program” button once.
• Enter a new user code. A total of 30 user codes may be programmed.
• Press the “Lock” button once.
• What lights and sounds does the lock produce?

One green flash with one beep

Three red flashes with three beeps

Programming was unsuccessful.

• Move swiftly through programming, as the system will time out if no button is pressed for five seconds
• Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt.
• Make sure the lock has room for an additional code. If all user code positions are filled, delete a code to make room for this one.

Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon.

Test the lock and check door alignment

• With the door open, press the “Lock” button. Confirm that the door locks.
• Enter the user code(s) added in the previous step. Confirm that the door unlocks
• Close the door. Press the “Lock” button. Confirm that the door locks smoothly without error
• If your does not lock smoothly, make sure you replaced your previous latch and strike with those supplied in the box.
• If you still experience locking errors, call Kwikset Support toorder a Warped Door Service Kit. Kwikset Support: 1-866-863-6584

Install the interior cover

• The window on the interior cover is locked by default to prevent someone from tampering with your lock’s  settings.
• If you wish to unlock the window, you can slide it up for more convenient access to the programming buttons while the cover is installed.
• To unlock the window, remove the security screw.

Important Information about the interior cover

Cover Installation

Battery Pack Access

• If the window is unlocked, remove the window to access the battery pack.
• If the window is locked, remove the interior cover and screws to access the battery pack.

SmartCode at a Glance

System Alerts

One incorrect code entered.

|

Re-enter code.

Keypad flashes red three times with three beeps*.

| No user code programmed.| Program at least one user code.
Programming timeout after five seconds.|

Attempt programming procedure again.

Unsuccessful programming.

Keypad flashes red 15 times with 15 beeps*

|

Three incorrect codes entered within one minute.

|

Re-enter code after 60 second keypad lockout.

Keypad flashes red with fast beeping sound for three to four seconds.|

Low battery.

|

Replace batteries.

Keypad flashes red with continuous beeping sound for two seconds.|

Door jammed while attempting to lock.

|

Manually re-lock door. If needed, reposition strike.

Lock beeps continuously.

| Interior assembly is disconnected from exterior.| Remove battery pack, reconnect the interior to the exterior, then reinstall battery pack.

Switches and Status LED colors

These features can be adjusted in some smart home apps. Once the associated functions are set by Zigbee, the setting of switches #1, 2 & 3 no longer affect the lock operation until factory reset

1

| Door lock status LED blinks every 6 seconds

2

| Lock automatically re-locks door 30 seconds after unlocking. Disabled if no codes are programmed.
3| Audio
4| Not used.
Color| Lock Status
---|---
Blinking green| Unlocked
Blinking amber| Locked
Blinking red| Low battery

Solid red

| Door handing process did not work properly. See the online Programing and Troubleshooting Guide.

Troubleshooting

A complete SmartCode 914 Programming and Troubleshooting Guide is available at www.kwikset.com.

Deleting a single user code (manually at the lock)

Note : All codes may be deleted at once if the mastercode is enabled. For more information about the mastercode, consult the SmartCode 914 Programming and Troubleshooting Guide at www.kwikset.com

If no button is pressed for five seconds, the system will time out, and you will need to restart the procedure

Factory Reset

A factory reset will delete all codes associated with the lock, and it will remove it from your smart home system.

Network Information

ZigBee System Notes ZigBee is a “Wireless mesh network,” and results may vary based on building construction and communication path, with 35+ feet being typical installed distance in a standard home environment and 250 feet+ when the lock has a clear line of sight with the smart home controller or hub. It may be necessary to install additional ZigBee devices to enhance the communication path between the lock and controller/hub for a  more robust ZigBee network.

Removing the lock from the network
Press button “B” on the lock interior nine times

SmartKey Re-Keying

Re-key the lock to work with your existing key. See the supplied SmartKey Re- key instructions for more information.
Note : If Auto-Lock is enabled (see “Switches and Status LED Colors”), remove the battery pack before re-keying your lock.

Important Safeguards

1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Protect your user codes and mastercode.
5. Dispose of used batteries according to local laws and regulations.

CAUTION : Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings.
WARNING : This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.

©2021 Spectrum Brands, Inc. All Rights Reserved. Lake Forest, CA 92610.

References

• Drilling Instructions | Kwikset
• Door Locks, Door Hardware, Smart Locks & Smartkey Technology | Kwikset

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>