Kwikset 99160-020 SmartCode Touchpad Electronic Locks User Guide

June 4, 2024
Kwikset

Kwikset 99160-020 SmartCode Touchpad Electronic Locks - logo
2
Touchpad Electronic Locks
User Guide

Kwikset 99160-020 SmartCode Touchpad Electronic Locks

Welcome to the Kwikset family!
This guide will get you up and running with your new SmartCode™ Lock. If you have any issues, please visit our support center: kwikset.com
or call us at 1-800-327-5625.
BEFORE YOU BEGIN
Kwikset logo 2
Scan for easy 3D instructions Downloads the BILT app before you begin.

https://www.kwikset.com/doorprep

Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
28

Parts in the box

Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
27Kwikset 99160-020 SmartCode
Touchpad Electronic Locks - fig 25Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
26

Philips
screwdriver
No electric drills

Installation

Remove your existing deadbolt and strike

Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
24

https://sj83t.app.goo.gl/4VE8

If drilling a new door, use the supplied template and instructions available at: kwikset.com/doorprep

Install the latch

Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
23

Install the strike

Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
22

Install the exterior assembly

Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
21

If your door hole is 1-1/2” (38mm), remove the adapter ring, and discard it.Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
20

A Route cable under the latch.Kwikset 99160-020 SmartCode Touchpad
Electronic Locks - fig 19Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
18 B Route the cable through the center hole of the mounting plate.
Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
15 C Push the cable into the bottom hole of the mounting plate.
Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
16 D Insert the key and test the latch. If the latch does not extend or retract smoothly, adjust the screws. Leave bolt LOCKED/EXTENDED.Kwikset 99160-020 SmartCode Touchpad
Electronic Locks - fig 17

3.2 Install the interior assembly
Check to make sure the latch bolt is in the extended/locked position to install the interior assembly.
If the turn piece is not pointing up, rotate the turn piece until you hear a click.
Remove the interior cover from the interior assembly.Kwikset 99160-020
SmartCode Touchpad Electronic Locks - fig 12

Secure the interior assembly onto the mounting plate.Kwikset 99160-020
SmartCode Touchpad Electronic Locks - fig 11

A Connect the cable. Ensure a tight cable connection.
Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
10 B Route cable around the side notch and bottom of the interior assembly.
C Insert the flat blade into the turn piece shaft.
Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
8

Install the AA batteries

Ensure the door is open while installing batteries.

Note: Batteries are not included
Ensure correct polarity. For best results, use new, non-rechargeable Alkaline batteries only.

Add a User Code and install the cover

Add a User Code per instructions on page 19.
After the first User Code is created, the latch bolt will automatically retract and extend to learn the locking and unlocking the direction of the door.Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
6

Secure the interior cover onto the interior assembly.Kwikset 99160-020
SmartCode Touchpad Electronic Locks - fig 5

Bolt will extend and retract to learn the orientation of the door.
The keypad will indicate success or failure.
Green: Door handing was successful.
Red: Door handling was unsuccessful. Make sure the interior and batteries are correctly installed.

**** Before you can lock or unlock the door a User Code must be created. Refer to page 19 for instructions on how to create a User Code.

Locking

To lock your door, press the Lock button. The lock will beep and the keypad will flash amber as the bolt extends.
Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
2 Unlocking
To unlock your door, enter the User Code. The lock will beep and the keypad will flash green and beep twice as the bolt retracts.Kwikset 99160-020
SmartCode Touchpad Electronic Locks - fig 3

SmartCode™ at a Glance

Kwikset 99160-020 SmartCode Touchpad Electronic Locks - fig
1

  1. Number Buttons
    Used to enter User Codes. Each code must be 4 to 8 digits in length.

  2. Checkmark
    Used for programming.

  3. SmartKey Cylinder
    The rekeyable cylinder retracts and extends the latch bolt by key from the exterior.

  4. Lock Button
    Used for programming, clearing User Code entry errors, lighting up the keypad, and locking the door.

  5. Battery Holder
    Uses 4 AA Alkaline batteries, 1.5V

  6. Programming Button
    Used for programming functions.

  7. Turn the piece
    Lock and unlock from the interior.

  8. Battery Cover
    Push it upward and outward to replace the batteries.

SmartKey Re-Keying

Re-key the lock to work with your existing key. See the supplied
SmartKey Re-key instructions for more information.
Note: If Auto-Lock is enabled, remove the batteries before re-keying your lock.
Kwikset 99160-020 SmartCode Touchpad Electronic Locks -
fig

System Alerts

Operation Lights Sounds Explanation Troubleshoot
Unlock Flashes GREEN x2 2 beeps Successful unlock
Flashes RED x10 10 beeps Low battery Install fresh new batteries
Flashes RED x 3 3 beeps Incorrect User Code Check code, and retry
Flashes RED x15 15 beeps Exceed 3 incorrect User Code attempts Wait 1

minute, check the code, and retry
Lock| Flashes AMBER x2| 2 beeps| Successful lock|
Flashes RED x10| 10 beeps| Low battery| Install fresh new batteries
Alternate RED/ WHITE Flash x5| 5 beeps| Stuck/Jammed bolt| Clear jam and try again
Factory Reset| Flashes GREEN xl| 1 beep| Successful|
Flashes RED x3| 3 beeps| Unsuccessful| Retry factory reset steps.
Make sure to press the Programming Button one more time within 10 seconds after the long beep.
Programming| Flashes GREEN xl| 1 beep| Successful|
Flashes RED x3| 3 beeps| Unsuccessful| Review Programming steps

Programming

Ensure the door is open before performing any programming.
The programming button is located on the interior chassis below the battery holder (refer to page 17). During programming, if no button is pressed within 5 seconds, the system will time out and you will need to restart the procedure.

Programming Notes
Add User Code:
Up to 50 User Codes can be saved. User Codes should be 4 to 8 digits in length.
For security reasons, the first 4 digits of each User Code must be unique. For example, you are unable to program a User Code 1-2-3-4-5 as well as a User Code 1-2-3-4-6.
Press the lock button before entering your code to light up the keypad at night.
Enable/Disable Programming Code:
Optional: A Programming Code enables you to make programming changes without needing to access the programming button. This is ideal for landlords to allow programming from the outside without access to the interior programming button. One Programming Code can be saved and should be 4 to 8 digits in length.
The Programming Code can not be the same as any User Code and will not unlock the lock.
To program the lock when the Programming Code is enabled, instead of pressing the programming button, enter the Programming Code, press the checkmark, and proceed with the remaining steps on page 19. Repeat the programming steps to disable the Programming Code. Please note once a Programing Code is enabled, the programming button is disabled and can only be used to factory reset the lock.
Delete All User Codes:
The keypad locking function will be disabled when User Codes are deleted. The lock can only be operated manually by key during this time.
Enable/Disable Audio:
The LED status indicator will still function once the audio is disabled. Repeat the programming steps to enable the audio.
Enable/Disable User Codes:
When all User Codes are disabled, all electronic functions will be disabled as well. The door must be locked or unlocked manually with the key. Repeat the
programming steps to enable the User Codes.
Add One-Time Use Code:
Up to 10 One-time User Codes can be saved. One-time User Codes should be 4 to 8 digits in length. The One-Time User Code will be deleted automatically after it is
used. The same One-Time User Code can be created again after it’s used.
Change Auto-Lock Time Delay:
Press the keypad number that corresponds to your time delay preference:
“1”: 30 seconds
“2”: 1 minute
“3”: 3 minutes
“4”: 5 minutes
“5”: 10 minutes
Enable/Disable AutoLock:
The default setting is disabled. Once you enable auto-lock the default setting is set to 30 seconds.
To change the auto-lock time delay, see the “Change Auto-Lock Time Delay” programming step.
Repeat the programming steps to disable auto-lock.
Door Rehandling Identification:
Perform this process for the lock to learn the locking and unlocking direction of the door.
This feature is used for the lock to learn the orientation of your door (left- or righthanded). If a stuck/jammed bolt error continues to occur after performing this step, please make sure there is no obstruction from the strike or door jamb to prevent the bolt from extending.
Factory Reset:
A factory reset will delete all User Codes and change all programming to factory settings.

Important Safeguards

  1. Read all instructions in their entirety.
  2. Familiarize yourself with all warning and caution statements.
  3. Remind all family members of safety precautions.
  4. Always have access to your lock’s standard key.
  5. If using the Auto-Lock features, make sure you have your smartphone or standard key with you to prevent locking yourself out.
  6. Familiarize yourself with the system alerts.
  7. Replace low batteries immediately.
  8. Dispose of used batteries according to local laws and regulations.

WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.
CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the User Codes, you must restrict access to the back panel and routinely check the User Codes to ensure they have not been altered without your knowledge. The use of a programming code can help protect your system’s settings.

Regulatory Compliance

This product complies with standards established by the following regulatory bodies:

  • Federal Communications Commission (FCC)
  • Industry Canada

FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1 ) this device may not cause harmful interference, and ( 2 ) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT! Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Industry Canada
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation
is subject to the following two conditions: ( 1 ) This device may not cause interference, and ( 2 ) This device must accept any interference, including interference that may cause undesired operation of the device.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals