Autonics CX6S Series LCD Display Counter Timer User Manual
- June 17, 2024
- Autonics
Table of Contents
CX6S Series LCD Display Counter Timer
Product Information
Specifications:
- Product Name: LCD Display Counter/Timer
- Series: CX6S Series, CX6M Series
Product Usage Instructions
Safety Considerations:
-
Please observe all safety considerations for safe and proper
product operation to avoid hazards. The symbol represents caution
due to special circumstances in which hazards may occur. -
Warning: Failure to follow these instructions
may result in serious injury or death. -
Caution: Failure to follow these instructions
may result in personal injury or product damage.
Warning:
-
Fail-safe device must be installed when using the unit with
machinery that may cause serious injury or substantial economic
loss. (e.g. nuclear power control, medical equipment, ships,
vehicles, railways, aircraft, combustion apparatus, safety
equipment, crime/disaster prevention devices, etc.) Failure to
follow this instruction may result in fire, personal injury, or
economic loss. -
Install on a device panel to use. Failure to follow this
instruction may result in electric shock or fire. -
Do not connect, repair, or inspect the unit while connected to
a power source. Failure to follow this instruction may result in
electric shock or fire. -
Check ‘Connections’ before wiring. Failure to follow this
instruction may result in fire. -
Do not disassemble or modify the unit. Failure to follow this
instruction may result in electric shock or fire.
Caution:
-
When connecting the power input and relay output, use AWG 20
(0.50mm2) cable or over, and tighten the terminal screw with a
tightening torque of 0.74 to 0.90N.m. Failure to follow this
instruction may result in fire or malfunction due to contact
failure. -
Use the unit within the rated specifications. Failure to follow
this instruction may result in fire or product damage. -
Use the unit within the rated specifications. Failure to follow
this instruction may result in shortening the life cycle of the
unit or fire. -
Do not use the unit in the place where
flammable/explosive/corrosive gas, humidity, direct sunlight,
radiant heat, vibration, impact, or salinity may be present.
Failure to follow this instruction may result in fire or
explosion. -
Keep metal chip, dust, and wire residue from flowing into the
unit. Failure to follow this instruction may result in fire or
product damage.
Manual:
For detailed information and instructions, please refer to the
user manual and be sure to follow cautions. Visit our homepage
(www.autonics.com) to download
manuals.
Ordering Information:
CX 6 S – 1P 4 F
Signal input method:
-
No mark – Voltage input (PNP) / no-voltage input (NPN)
selectable type -
F – Free voltage input
Power supply:
- 2 – 24VAC 50/60Hz, 24-48VDC
- 4 – 100-240VAC 50/60Hz
Output:
- Size Display digit Item
- 1P – 1-stage setting
- 2P – 2-stage setting
- S – 6-digit
Unit Description:
- CX6S Series
- CX6M Series
Counting value display component:
RUN mode:
Displays counting value for counter operation or time progress
value for timer operation.
Function setting mode:
Displays parameter.
FAQ
Q: Where can I download the user manual?
A: You can download the user manual from our homepage at
www.autonics.com.
Q: What should I do if I notice metal chip, dust, or wire
residue flowing into the unit?
A: It is important to keep metal chip, dust, and wire residue
from flowing into the unit as it may result in fire or product
damage. Ensure the unit is placed in a clean environment and
regularly clean around the unit to prevent any debris from
entering.
DRW171461AB
LCD Display Counter/Timer
CX SERIES
INSTRUCTION MANUAL
CX6S Series
CX6M Series
Thank you for choosing our Autonics product. Please read the following safety considerations before use.
Safety Considerations
Please observe all safety considerations for safe and proper product operation
to avoid hazards. symbol represents caution due to special circumstances in
which hazards may occur.
Warning Failure to follow these instructions may result in serious injury or
death.
Caution Failure to follow these instructions may result in personal injury or
product damage.
Warning
1. Fail-safe device must be installed when using the unit with machinery that
may cause serious injury or substantial economic loss. (e.g. nuclear power
control, medical equipment, ships, vehicles, railways, aircraft, combustion
apparatus, safety equipment, crime/disaster prevention devices, etc.) Failure
to follow this instruction may result in fire, personal injury, or economic
loss.
2. Install on a device panel to use. Failure to follow this instruction may
result in electric shock or fire.
3. Do not connect, repair, or inspect the unit while connected to a power
source. Failure to follow this instruction may result in electric shock or
fire.
4. Check `Connections’ before wiring. Failure to follow this instruction may
result in fire.
5. Do not disassemble or modify the unit. Failure to follow this instruction
may result in electric shock or fire.
Caution
1. When connecting the power input and relay output, use AWG 20 (0.50mm2)
cable or over, and tighten the terminal screw with a tightening torque of 0.74
to 0.90N.m. Failure to follow this instruction may result in fire or
malfunction due to contact failure.
2. Use the unit within the rated specifications. Failure to follow this
instruction may result in fire or product damage.
3. Use the unit within the rated specifications. Failure to follow this
instruction may result in shortening the life cycle of the unit, or fire.
4. Do not use the unit in the place where flammable/explosive/corrosive gas,
humidity, direct sunlight, radiant heat, vibration, impact, or salinity may be
present. Failure to follow this instruction may result in fire or explosion.
5. Keep metal chip, dust, and wire residue from flowing into the unit.
Failure to follow this instruction may result in fire or product damage.
Manual
For the detail information and instructions, please refer to user manual and
be sure to follow cautions. Visit our homepage (www.autonics.com) to download
manuals.
Ordering Information
CX 6 S – 1P 4 F
Signal input method
No mark
Voltage input (PNP) /no-voltage input (NPN) selectable type
F
Free voltage input
Power supply
2
24VAC 50/60Hz, 24-48VDC
4
100-240VAC 50/60Hz
Output
Size Display digit Item
1P
1-stage setting
2P
2-stage setting
S
DIN W48×H48mm
M
DIN W72×H72mm
6
999999 (6-digit)
CX
LCD Display Counter/Timer
Unit Description
CX6S Series
CX6M Series
1
7
2
1
8
9
3
7
4
10
5
8
2
11
6
9
3
12 13 14
10
4 5
11
6
1. Counting value display component (red) RUN mode
12 13
14
: Displays counting value for counter operation or time progress value for timer operation.
Function setting mode: Displays parameter.
2. Setting value display component (green)
RUN mode: Displays setting value.
Function setting mode: Displays parameter setting value.
3. Time unit indicator (h:m:s): Turns ON for time unit for timer.
4. Key lock indicator ( ): Turns ON for key lock setting.
5. Reset input indicator (RST): Turns ON for reset key input or reset signal input.
6. INH indicator (INH)
: For the voltage input (PNP)/no-voltage input (NPN) selectable model (CX6 – ),
it turns ON for INHIBIT signal input.
(In case of CX6S Series and timer mode, it turns ON for INB/INH signal input.)
For free voltage input model (CX6 – F), it turns ON for INB/INH signal input for timer.
7. Output indicator (OUT1, OUT2): Turns ON for the dedicated control output ON.
8. SV checking and changing indicator (SET, SET1, SET2) (green)
: Turns ON when checking and changing SV.
9. COUNTER indicator (COUNTER): Turns ON for counter operation. 10. TOTAL indicator1 (TOTAL)
: In case of TOTAL counter display mode, it turns ON with the COUNTER indicator.
11. TIMER indicator (TIMER)
: Flashes (progressing time) or Turns ON (stopping time) for timer operation.
12. RESET key
RUN mode, Function setting mode
: Press the RESET key to reset the counting value and turn OFF the output. TOTAL counter display mode1: Press the RESET key to reset the counting value of TOTAL counter.
key
RUN mode: Hold the Press the
key over 3 sec to enter function setting mode. key to select SV2 (SET2)/SV1 (SET1)/TOTAL counter1 display for
counter operation.
Function setting mode: Hold the
key over 3 sec to return RUN mode.
Press the
key to save the SV and enter the next setting.
Function setting check mode: Hold the
key over 1 sec to return RUN mode.
Changing SV mode: Press the
key to save SV and return RUN mode.
14. , key
- key
RUN mode: Press the key to change SV and move SV (SET, SET1, SET2) digits.
Changing SV mode: Press the key to change digits.
- key
Changing SV mode: Increases SV.
Function setting mode: Changes the settings.
1: This is for the voltage input (PNP)/no-voltage input (NPN) selectable model (CX6 – ).
Specifications
Model
CX6S-1P
CX6S-2P
CX6M-1P
CX6M-2P
Display digits
6-digit
Display method
7-segment (1st, 2nd digits of counting value display: white, setting value display: green) LCD method, 11-segment (the other digits of counting value display: white) LCD method, Operation display part: yellow LCD method
Character Counting value size (W×H) Setting value
Power supply
AC voltage AC/DC voltage
4.1×10.1mm
3.3×8.1mm 100-240VAC 50/60Hz 24VAC 50/60Hz, 24-48VDC
6.2×15.2mm 5×12.3mm
Permissible voltage range 90 to 110% of rated voltage
Power consumption
AC
CX6 –
Max. 6.4VA
voltage CX6 – F Max. 4.2VA
Max. 6.7VA Max. 4.9VA
Max. 7.1VA Max. 4.7VA
Max. 7.5VA Max. 5.4VA
AC/DC CX6 voltage CX6 –
AC: max. 5.5VA AC: max. 5.6VA AC: max. 6.2VA AC: max. 6.3VA DC: max. 3.5W DC: max. 3.6W DC: max. 4W DC: max. 4.1W
F
AC: DC:
max. max.
3.6VA 2.5W
AC: max. 4.0VA DC: max. 2.8W
AC: max. 3.9VA DC: max. 2.9W
AC: max. 4.5VA DC: max. 3.3W
Max. INA/INB CX6 –
counting
speed
CX6 –
Selectable among 1cps/30cps/300cps/1kcps/5kcps F 20cps
Counter
Counting range
-99999 to 999999
Scale
Decimal point up to fifth digit
Min. signal CX6 –
RESET, TOTAL RESET signal: selectable among 1ms/20ms
width
CX6 – F RESET signal: 25ms
Time range
999.999s, 9999.99s, 99999.9s, 999999s, 99m59.99s, 999m59.9s, 9999m59s, 99999.9m, 999999m, 99h59m59s, 9999h59m, 99999.9h
Operation mode
Up, Down
Timer
Min. signal CX6 –
INA, INHIBIT, RESET, TOTAL RESET signal: selectable among 1ms/20ms
width
CX6 – F INA, INH, RESET signal: 25ms
Repeat error Set error Voltage error Temp. error
[CX6 [CX6 –
]-In case of power ON start: max. ±0.01% ±0.05s In case of signal ON start:
max. ±0.01% ±0.03s
F]-In case of power ON start: max. ±0.01% ±0.08s In case of signal ON start:
max. ±0.01% ±0.06s
Input method
CX6 CX6 –
Selectable among voltage input (PNP)/no-voltage input (NPN) [Voltage input
(PNP)]-input impedance: 10.8k,
H: 5-30VDC, [L]: 0-2VDC [No-voltage input (NPN)]-short-circuit impedance:
max. 1k,
short-circuit residual voltage: max. 2VDC
[Free voltage input]-INA (START) , INB (INHIBIT) input
F
24-240VDC/24-240VAC 50/60Hz, [L]: 0-10VDC/VAC input]-RESET input, short- circuit impedance: max. 1k,
short-circuit residual voltage: max. 2V
One-shot output time 0.01 to 99.99s setting
Control
Contact
Type Capacity
SPDT (1c): 1 Max. 250VAC
SPST (1a): 2 SPDT (1c): 1 3A, 30VDC 3A resistive load
SPDT (1c): 2
output Solid state
Type
–
Capacity
NPN open
NPN open
collector: 1
collector: 2
Max. 30VDC 100mA
External power supply1 Max. 12VDC ±10%, 100mA
Memory retention
Approx. 10 years (non-volatile memory)
Insulation resistance
Over 100M (at 500VDC megger)
Dielectric strength
3,000VAC 50/60Hz for 1 min
Noise AC voltage Square-wave noise by noise simulator (pulse width 1) ±2kV immunity AC/DC voltage Square-wave noise by noise simulator (pulse width 1) ±500V
Mechanical Vibration
Malfunction
0.75mm amplitude at frequency 10 to 55Hz (for 1 min) in each X, Y, Z direction for 1 hour 0.5mm amplitude at frequency 10 to 55Hz (for 1 min) in each X, Y, Z direction for 10 minutes
Shock
Mechanical 300m/s² (approx. 30G) in each X, Y, Z direction for 3 times Malfunction 100m/s² (approx. 10G) in each X, Y, Z direction for 3 times
Relay life Mechanical Min. 5,000,000 operations
cycle
Malfunction Min. 100,000 operations
Protection structure
Front part: IP50 (IEC standard)
Environ- Ambient temp. -10 to 55, storage: -25 to 65
ment
Ambient humi. 35 to 85%RH, storage: 35 to 85%RH
Approval
AC voltage
CX6 CX6 –
Approx. 157g (approx. 112g)
F
Approx. 155g (approx. 110g)
Approx. 162g (approx. 117g) Approx. 160g (approx. 115g)
Approx. 235g (approx. 170g) Approx. 233g (approx. 168g)
Approx. 240g (approx. 175g) Approx. 238g (approx. 173g)
Weight2
AC/DC voltage
CX6 CX6 –
Approx. 156g (approx. 111g)
F
Approx. 154g (approx. 109g)
Approx. 161g (approx. 116g) Approx. 159g (approx. 114g)
Approx. 234g (approx. 169g) Approx. 232g (approx. 167g)
Approx. 239g (approx. 174g) Approx. 237g (approx. 172g)
1: This is for the voltage input (PNP)/no-voltage input (NPN) selectable model (CX6 – ). 2: The weight includes packaging. The weight in parenthesis is for unit only. Environment resistance is rated at no freezing or condensation.
The above specifications are subject to change and some models may be
discontinued without notice.
Be sure to follow cautions written in the instruction manual, user manual and
the technical descriptions (catalog, homepage).
45+00.6
68+00.7
Dimensions
48
6
64.5
72
6
64.5
44.8 Min. 65
(unit: mm)
Panel cut-out
Min. 65
45+00.6
Min. 91
68+00.7
67.5 Min. 91
4 3.3
Bracket
CX6S Series 48.6±0.2 45 +00.2
30.6 20 5
16
+0.3 0
CX6M Series 46
+0.2 -0.05
36
44.9
37.5 40.5
55
15
21
12
23.9
56
Terminal cover (sold separately)
CX6S Series (RSA-COVER, 48×48mm)
22
3
48.4
13
CX6M Series (RMA-COVER, 72×72mm)
4
70
10
64
68.5
18 22
41 45
13
Connections
CX6S Series
1. Voltage input (PNP)/no-voltage input (NPN) selectable model
CX6S-1P CONTACT OUT: 250VAC 3A, 30VDC 3A RESISTIVE LOAD
CX6S-2P2 CONTACT OUT1/OUT2: 250VAC 3A, 30VDC 3A RESISTIVE LOAD
CX6S-2P4 CONTACT OUT1/OUT2: 250VAC 3A, 30VDC 3A RESISTIVE LOAD
1
7 INA
1 OUT2 7 INA
1
7 INA
2 OUT 8 INB/INH
3
9 12VDC 100mA
2
8 INB/INH
3 OUT1 9 12VDC 100mA
2
8 INB/INH
OUT2
3
9 12VDC 100mA
4 1
5
10 0VDC 11 RESET
4
10 0VDC
5
11 RESET
4
10 0VDC
OUT1
5
11 RESET
6
12 TOTAL RESET
6
12 TOTAL RESET
6
12 TOTAL RESET
SOURCE: 100-240VAC 50/60Hz 6.4VA 24VAC 50/60Hz 5.5VA 24-48VDC 3.5W
SOURCE: 24VAC 50/60Hz 5.6VA 24-48VDC 3.6W
SOURCE: 100-240VAC 50/60Hz 6.7VA
2. Free voltage input model
CX6S-1P F CONTACT OUT : 250VAC 3A, 30VDC 3A RESISTIVE LOAD SIGNAL INPUT : 24-240VAC 50/60Hz, 24-240VDC
CX6S-2P2F CONTACT OUT1/OUT2 : 250VAC 3A, 30VDC 3A RESISTIVE LOAD SIGNAL INPUT : 24-240VAC 50/60Hz, 24-240VDC
CX6S-2P4F CONTACT OUT1/OUT2 : 250VAC 3A, 30VDC 3A RESISTIVE LOAD SIGNAL INPUT : 24-240VAC 50/60Hz, 24-240VDC
1
7
INA
OUT2
1
7
INA
1
7
INA
2
8
INB/INH
2
8
INB/INH
2
8
OUT2
INB/INH
3 OUT
9
INPUT
4 1
5
10 11
RESET
3
9
OUT1
4
10
INPUT
5
11
RESET
3
4 OUT1
5
9
10
11 RESET
INPUT
6
12
0VDC
6
12
0VDC
6
12
0VDC
SOURCE: 100-240VAC 50/60Hz 4.2VA SOURCE: 24VAC 50/60Hz 4.0VA
24VAC 50/60Hz 3.6VA
24-48VDC 2.8W
24-48VDC 2.5W
SOURCE: 100-240VAC 50/60Hz 4.9VA
CX6M Series
1. Voltage input (PNP)/no-voltage input (NPN) selectable model
CX6M-1P CONTACT OUT: 250VAC 3A, 30VDC 3A RESISTIVE LOAD
CX6M-2P CONTACT OUT1/OUT2: 250VAC 3A, 30VDC 3A RESISTIVE LOAD
1 2 OUT 3 4
10 INA
11 INB
12 12VDC 100mA 0VDC
13
1 2 OUT2 3 4
10 INA
11 INB 12 12VDC 100mA 0VDC 13
5
14 RESET
5 OUT1
14 RESET
6
15 INHIBIT
6
15 INHIBIT
7 1
8
9
SOLID STATE OUT: 30VDC 100mA
16 TOTAL RESET 17 18
7 1
8
9
SOLID OUT1 16 TOTAL RESET
STATE
OUT:
17
30VDC
100mA
18
OUT2
SOURCE: 100-240VAC 50/60Hz 7.1VA 24VAC 50/60Hz 6.2VA 24-48VDC 4W
SOURCE: 100-240VAC 50/60Hz 7.5VA 24VAC 50/60Hz 6.3VA 24-48VDC 4.1W
2. Free voltage input model CX6M-1P F
CONTACT OUT: 250VAC 3A, 30VDC 3A RESISTIVE LOAD
SIGNAL INPUT: 24-240VAC 50/60Hz, 24-240VDC
CX6M-2P F CONTACT OUT1/OUT2: 250VAC 3A, 30VDC 3A
RESISTIVE LOAD SIGNAL INPUT: 24-240VAC 50/60Hz, 24-240VDC
1 2 OUT 3 4
10 INA
11 INB/INH
12 SIGNAL INPUT
13
1 2 OUT2 3 4
10 INA
11 INB/INH
12 SIGNAL INPUT
13
5
14
5 OUT1
14
6 7 1 8
9
15
0VDC RESET
16
SOLID
STATE
OUT:
17
30VDC
100mA
18
6 7 1 8
9
15
0VDC RESET
16 SOLID
STATE
OUT: 30VDC
OUT1 17
100mA OUT2 18
SOURCE: 100-240VAC 50/60Hz 4.7VA 24VAC 50/60Hz 3.9VA 24-48VDC 2.9W
1: AC voltage: 100-240VAC 50/60Hz AC/DC voltage: 24VAC 50/60Hz, 24-48VDC
SOURCE: 100-240VAC 50/60Hz 5.4VA 24VAC 50/60Hz 4.5VA 24-48VDC 3.3W
Operations
1. Operation and setting (counter/timer)
(RUN mode)
(CX6 – )
TOTAL counter
RESET
Reset TOTAL counter
SET 1 value
SET 2 value
(CX6 – F)
[Counter]
Function setting mode
3 sec 3 sec
RUN mode
1 sec
Changing SV
mode
Function setting 1 sec check mode
(RUN mode)
RESET PV RESET
12:30:25
OUT 1
OUT 2 1:25:47
SET 2
TIMER
Display PV Display SET 2
1-1. Function setting mode
12:34:56
OUT 1
OUT 2 SET 1
5:43:50
TIMER
Display PV Display SET 1
[Timer]
Hold the
key over 3 sec to enter function setting mode in RUN mode.
Set the function by the , keys.
Hold the
key over 3 sec to return RUN mode in function setting mode.
1-2. Function setting check mode
Hold the key over 1 sec to enter function setting check mode in RUN mode.
When checking the saved parameters, press the , key to check next item..
Hold the
key over 1 sec at function setting check mode and it returns to RUN mode.
1-3. RESET
In RUN mode, function setting mode, press the RESET key to reset the current value and the output
turns OFF.
At TOTAL counter display mode1, press the RESET key to reset TOTAL counter counting value and
the current counting value.
1: This is for the voltage input (PNP)/no-voltage input (NPN) selectable model (CX6 – ).
TOTAL counter display mode is only for counter operation.
2. Function setting
RUN mode
3 sec
Function setting mode
3 sec
Counter [COUNT]
Timer [TIME] Counter/Timer [C-T]
Input mode [InM] Output mode [OUtM]
Up/Down mode [U-D] Output mode [OUtM]
(In case of OND, ONdI, ONd2, ONd3, FLk1, FLk2, INT, INt1, INt2, OFD, INTG, TOTAL1, ONtD)
Max. counting speed1 [CPS] OUT 2 output time [OUT2]
(In case of FLK, NFD, NFdI)
Output ON time range [OnRNG]
Time range [tRNG]
OUT output time
[OUtT]
OUT 1 output time [OUT1]
Decimal point [DP]
Min. reset time1 [RESET]
Output OFF time range [OFfRNG] OUT 2 output time [OUT2] OUT 1 output time [OUT1]
(2-stage output model)
(1-stage output model)
OUT output time [OUtT]
Input logic1 [SIG]
Input logic1 [SIG]
Prescale decimal point [SClDP] Prescale value [SCL] TOTAL counter2 [TOTAL] Start point value [START] Memory protection [DATA] Key lock [LOCK]
Input signal time1 [IN-T]
Memory protection2 [ D A T A ]
Key lock [LOCK] 1: In case of free voltage input model (CX6 – F), these
parameters do not appear due to fixed setting.
2:This parameter is for the voltage input (PNP)/no-voltage input (NPN)
selectable model (CX6 – ).
: When changing the setting of shaded parameters, all output turn OFF. When
returning RUN mode, PV is reset.
Counter Mode
1. Parameter setting (
key: Moves parameters, key: Changes parameter setting value)
Parameter Parameter setting value
Counter/Timer [C-T]
COUNT
TIME
COUNT: Counter TIME: Timer
Input mode [InM]
UP UP-1 UD-C1
UP-2 UP-3 DN DN-1 UD-B1 UD-A DN-3 DN-2
Input mode is UP, UP-1, UP-2, UP-3 or DN, DN-1, DN-2, DN-3, F N [ RKPQA
Output mode Input mode is UD-A, UD-B1, UD-C1
[OUtM]
F N [ RKPQASTD
If max. counting speed is 5kcps, and output mode is D, max. counting speed is automatically changed as 30cps, factory default.
Max. counting 30 300 1K 5K 1 speed2 [CPS]
Max. counting speed is when duty ratio of INA or INB input signal is 1:1.
It is applied for INA, or INB input as same. When output mode is D, set max.
counting speed
one among 1cps, 30cps, 300cps, or 1kcps.
OUT 2
Set one-shot output time of OUT 2.
output time3 Setting range: 00.01 to 99.99 sec
[OUT2]
W hen output mode is F, N, S, T, D, this parameter does not appear. (fixed as HOLD)
OUT 1 output time3 [OUT1]
Set one-shot output time of OUT 1. Setting range: 00.01 to 99.99 sec, Hold When number of tens digit is flashing, press the key once and HOLD appears. When output mode is S, T, D, this parameter does not appear. (fixed as HOLD)
OUT output time3 [OUtT]
Setting range: 00.01 to 99.99 sec When output mode is F, N, S, T, D, this parameter does not appear. (fixed as HOLD)
Decimal point4 —— —–.- —-.– —.—
[DP] Decimal point is applied to PV and SV.
Min. reset time2 1
20, unit: ms
[RESET]
Set min. width of external reset signal input.
Input logic2 [SIG]
NPN: No-voltage input, PNP: Voltage input
–.—-
-.—–
Prescale
-.—– —–.- —-.– —.— –.—-
decimal point4
[SClDP]
Decimal point of prescale should not set smaller than decimal point [DP].
Prescale
Setting range: 0.00001 to 99999.9
value [SCL] Setting range of prescale is linked with prescale decimal point [SClDP] setting.
TOTAL counter1 ON [TOTAL]
OFF
Start point value [START]
Setting range of start point value is linked with decimal point [DP] setting.
(0.00000 to 999999)
WheninputmodeisDN, DN-1, DN-2, this parameter doesnotappear.
WhentotalcountfunctionisON,thisparameter does not appear.1
Memory protection CLR [DATA]
CLR: Resets the counting value when power OFF.
REC
REC: Maintains the counting value when power OFF.
(memory protection)
Key lock [LOCK]
lOFF: Unlock keys, key lock indicator turns OFF
lOFF LOc1
LOc1: Locks RESET key, key lock indicator turns ON
LOc3 LOc2 LOc2: Locks , keys, key lock indicator turns ON LOc3: Locks , RESET , keys, key lock indicator turns ON
1: For voltage input (PNP), no-voltage input (NPN) model (CX6 – ). 2: For free
voltage input model(CX6 – F), these parameters do not appear due to fixed
setting. 3: For 1-stage setting model (CX6 -1P ), OUT1 does not appear.
The OUT2 output time is displayed as OUtT.
4: Decimal point and prescale decimal point -Decimal point: Set the decimal
point for display value regardless of prescale value.
-Prescale decimal point
: Set the decimal point for prescale value of counting value regardless of
display value.
2. Input mode
Input mode Counting chart
Operation
INA
H L
No counting
Up [UP]
INB
H L
No counting
4
Count 1
2
3
0
When INA is counting input,
5
67
INB is no counting input. When INB is counting input,
INA is no counting input.
Up-1 [UP-1]
INA
H L
INB
H L
Count 0
2 1
No counting 3
When INA input signal is
rising ( ) , it counts.
4
5 INA: Counting input
INB: No counting input
Up-2 [UP-2]
INA
H L
INB
H L
Count
1
0
When INA input signal is
falling ( ) , it counts.
No counting 2
3
4
INA: Counting input
INB: No counting input
INA
H L
Up-3
INB
H L
When INA or INB input signal is rising ( ) , it counts.
[UP-3]
Count
3
5
6 INA: Counting input INB: Counting input
1
2
0
Down [DN]
INA
H L
INB
H L
n n-1
Count
0
No counting n-2
No counting
n-3 n-4 n-5
n-6
When INA is counting input, INB is no counting input. When INB is counting
input, INA is no counting input.
n-7
Down-1 [DN-1]
INA
H L
INB
H L
n n-1
n-2
Count
0
No counting n-3
When INA input signal is rising ( ) , it counts.
INA: Counting input INB: No counting input
n-4 n-5
Down-2 [DN-2]
INA
H L
INB
H L
n n-1
Count
0
No counting n-2
When INA input signal is
falling ( ) , it counts.
INA: Counting input
n-3
INB: No counting input
n-4
n-5
INA
H L
Down-3 [DN-3]
INB
H L
n
n-1
Count
n-2
0
When INA or INB input signal
is rising ( ) , it counts.
INA: Counting input
n-3
INB: Counting input
n-5
n-6
INA
H L
Up/Down-A [UD-A]
INB
H L
4
3
Count
2
1
0
INA: Counting input
INB: Counting command input
When INB is “L”,
4 counting command is up.
3 2
1
2
3
When INB is “H”, counting command is down.
INA
H L
Up/Down-B1 [UD-B]
INB
H L
4 3
Count
2 1
0
INA: Up counting input
INB: Down counting input
3
3
4
When INA and INB input signals are rising ( ) at
22
the same time, it maintains
previous counting value.
INA
H L
Up/Down-C1 [UD-C]
INB
H L
Count
0
3
2
2
1
1
When connecting encoder
output A, B phase with
counter input, INA, INB, set
3 2
input mode [InM] as phase different input [UD-C] for
counter operation.
1: This is for the voltage input (PNP)/no-voltage input (NPN) selectable model (CX6 – ).
A: over min. signal width, B: over than 1/2 of min. signal width. If the signal is smaller than these width, it may cause counting error (±1).
INA H (INB) L
ON OFF ON OFF T.on T.off
T
T.on, T.off: Min. signal width
The meaning of “H”, “L”
Input Voltage
method input
Character
(PNP)
No-voltage input (NPN)
H
5-30VDC Short
L
0-2VDC Open
Min. signal width by counting speed
CX6 –
CX6 –
Counting Min. signal
speed
width
Counting speed
1cps
500ms
20cps
30cps
16.7ms
300cps 1.67ms
1kcps
0.5ms
5kcps
0.1ms
F
Min. signal width 25ms
3. Prescale function This function is to set and display calculated unit for
actual length, liquid, position, etc. It is called “prescale value” for
measured length, liquid, or position, etc per 1 pulse. For example, when
moving L, the desired length to be measured, and P, the number of pulses per 1
revolution of a rotary encoder, occurs, prescale value is L/P. E.g.)
Positioning control by counter and encoder
Pulley
Cutter
Rotary encoder
Motor
Motor conlrol system
Counter
[Diameter (D) of pulley connected with encoder=22mm, the number of pulses by 1 rotation of
encoder=1,000]
*Prescale value
=
× Diameter (D) of pulley
The number of pulses by 1
= 3.1416 × 22 1000
= 0.069mm/pulse
rotation of encoder
Set decimal point [DP] as [—–.-], prescale decimal point [SClDP] as [—.—], and prescale value [SCL] as [)069] at function setting mode. It is available to control conveyor position by 0.1mm unit.
Timer Mode
1. Parameter setting (
key: Moves parameters, key: Changes parameter setting value)
Parameter
Parameter setting value
Counter/Timer [C-T]
COUNT
TIME
COUNT: Counter TIME: Timer
Up/Down mode [U-D]
UP
DN
UP: Time progresses from ‘0’ to the setting time. DN: Time progresses from the setting time to ‘0’.
Output mode [OUtM]
OND ONd1 ONd2 ONd3 FLK FLk1 FLk2 INT ONtD TOTAL1 INTG NFd1 NFD OFD INt22 INt1
Time range [tRNG]3
output ON TIME range [OnRNG]4, output OFF TIME range [OFfRNG]4
999.999
TIMER
s
99999.9 TIMER h
9999.99
TIMER
s
9999:59
TIMER
h:m
99999.9
TIMER
s
99:59:59 TIMER h:m:s
999999
TIMER
s
999999
TIMER
m
99:59.99
TIMER
m:s
99999.9
TIMER
m
999:59.9
TIMER
m:s
9999:59
TIMER
m:s
OUT 2 output time5
[OUT2]
Set one-shot output time of OUT 2. Setting range: 00.01 to 99.99 sec, Hold When number of tens digit is flashing, press the
key once and HOLD appears.
OUT 1 output time5
[OUT1]
Set one-shot output time of OUT 1. Setting range: 00.01 to 99.99 sec, Hold When number of tens digit is flashing, press the
key once and HOLD appears.
OUT output time5 [OUtT] Input logic6 [SIG]
Setting range: 00.01 to 99.99 sec, Hold When number of tens digit is flashing, press the key once and HOLD appears. NPN: No-voltage input, PNP: Voltage input
Input signal time6
[IN-T]
1
20, unit: ms
Set min. width of INA, INHIBIT, RESET, TOTAL RESET signal
Memory protection [DATA]
CLR
REC
CLR: Resets the counting value when power OFF.
REC: Maintains the counting value when power OFF. (memory protection)
lOFF: Unlock keys, key lock indicator turns OFF
Key lock
lOFF LOc1
LOc1: Locks RESET key, key lock indicator turns ON
[LOCK]
LOc3 LOc2 LOc2: Locks , keys, key lock indicator turns ON LOc3: Locks , RESET , keys, key lock indicator turns ON
1: This is for the voltage input (PNP)/no-voltage input (NPN) selectable model (CX6 – ).
2: INt2 mode is available only for 2-stage setting model(CX6 -2P ). 3: When output mode is OND, ONd1, ONd2, ONd3, FLk1, FLk2, INT, INt1, INt2, OFD, INTG,
TOTAL, ONtD, set time range [tRNG]. 4: When output mode is FLK, NFD, NFD.1, set output ON TIME range [OnRNG] and output OFF
TIME range [OFfRNG]. 5: In case of 1-stage setting model (CX6 -1P ), OUT1 output time does not appear.
OUT2 output time is displayed as OUtT. 6: In case of free voltage input model (CX6 – F), this parameter does not appear due to fixed
setting.
One-shot output (0.01 to 99.99 sec) Retained output
One-shot output
Retained output
2. Timer ‘0’ time setting
2-1. Timer output mode for ‘0’ time setting [OND, ONd1, ONd2, ONd3, NFD, NFd1] 2-2. Operations by output mode (‘0’ time setting)
A. OND (Signal ON Delay) mode [OND]
Set ‘0’ for setting time 1.
Up mode
Down mode
Set `0′ for setting time 2.
INA (START) Setting time 2
INA (START) Setting time 1
0 OUT 1
OUT 2
B. OND.1 (Signal ON Delay 1) mode [ONd1]
Set `0′ for setting time 1.
Up mode
Down mode
INA (START)
RESET Setting time 2
0 OUT 1 OUT 2
Set `0′ for setting time 2.
INA (START) RESET
Setting time 1
0
OUT 1
OUT 2
C. OND.2 (Power ON Delay) mode [ONd2]
Set `0′ for setting time 1.
Up mode
Down mode
POWER RESET Setting time 2
0 OUT 1 OUT 2
Set `0′ for setting time 2. Up mode
POWER RESET Setting time 1
0 OUT 1
OUT 2
D. OND.3 (Power ON Delay) mode [ONd3]
Set `0′ for setting time 1.
Up mode
Down mode
POWER
RESET Setting time 2
0 OUT 1 OUT 2
Set `0′ for setting time 2. Up mode
POWER RESET Setting time 1
0
OUT1
OUT2
E. NFD (ON-OFF Delay) mode [NFD] Set ‘0’ for Off_Delay setting time.
INA (START) RESET
UP DISPLAY DOWN
On_Delay 0
On_Delay 0
OUT 2 (OUT)
F. NFD.1 (ON-OFF Delay1) mode [NFd1] Set `0′ for Off_Delay setting time.
INA (START) RESET
UP DISPLAY DOWN
On_Delay 0
On_Delay 0
OUT 2 (OUT)
0 OUT1 OUT2
Set `0′ for On_Delay setting time.
INA (START) RESET
UP
Off_Delay
DISPLAY
0
DOWN Off_Delay
0
OUT 2 (OUT)
Set `0′ for On_Delay setting time.
INA (START) RESET
UP
Off_Delay
DISPLAY
0
DOWN Off_Delay
0
OUT 2 (OUT)
Factory Default
Parameter
Factory default CX6 –
CX6 – F
InM
UD-C
UD-A
OUtM
F
F
CPS
30
–
OUT2 (OUtT1) OUT11
HOLD (fixed) 0)10
HOLD (fixed) 0)10
DP
——
——
Counter
RESET
20ms
–
SIG
NPN
–
SClDP
-.—–,
-.—–,
SCL
!00000
!00000
TOTAL2
OFF
–
START
000000
000000
DATA
CLR
CLR
U-D
UP
UP
OUtM
OND
OND
OUT2 (OUtT1)
HOLD
HOLD
Timer
OUT11
0)10
0)10
tRNG
99(999s
99(999s
SIG2
NPN
–
IN-T
20ms
–
LOCK
lOFF
lOFF
SET1
1000
1000
SET2
5000
5000
1: For 1-stage setting model (CX6 -1P ), OUT1 does not appear.
The output time of OUT2 is displayed as OUtT. 2: This is for the voltage input
(PNP)/no-voltage input (NPN) selectable model (CX6 – ).
Error Display and Output Operation
Error Display
Error description
Troubleshooting
ERR0
Setting value is 0.
Change the setting value anything but 0.
When error occurs, the output turns OFF. When 1st setting value is set as 0
(zero), OUT1 maintains OFF.
When 2nd setting value is smaller than 1st setting value, 1st setting value is
ignored and only OUT2 output operates.
Indicator model does not have error display function.
Cautions during Use
1. Follow instructions in Cautions during Use’. Otherwise, it may cause unexpected accidents. 2. In case of 24-48VDC, 24VAC model, power supply should be insulated and limited voltage/ current or Class 2, SELV power supply device. 3. Use the product, 0.1 sec after supplying power. 4. When supplying or turning off the power, use a switch or etc. to avoid chattering. 5. Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting the power. 6\. Keep away from high voltage lines or power lines to prevent inductive noise. In case installing power line and input signal line closely, use line filter or varistor at power line and shielded wire at input signal line. Do not use near the equipment which generates strong magnetic force or high frequency noise. 7\. This unit may be used in the following environments. Indoors (in the environment condition rated inSpecifications’) Altitude max.
2,000m Pollution degree 2 Installation category II
Major Products
Photoelectric Sensors
Temperature Controllers
Fiber Optic Sensors
Temperature/Humidity Transducers
Door Sensors
SSR/Power Controllers
Door Side Sensors
Counters
Area Sensors
Timers
Proximity Sensors
Panel Meters
Pressure Sensors
Tachometer/Pulse (Rate) Meters
Rotary Encoders
Display Units
Connector/Sockets
Sensor Controllers
Switching Mode Power Supplies
Control Switches/Lamps/Buzzers
I/O Terminal Blocks & Cables
Stepper Motors/Drivers/Motion Controllers
Graphic/Logic Panels
Field Network Devices
Laser Marking System (Fiber, Co, Nd: YAG)
Laser Welding/Cutting System
http://www.autonics.com
HEADQUARTERS: 18, Bansong-ro 513 beon-gil, Haeundae-gu, Busan, South Korea,
48002 TEL: 82-51-519-3232 E-mail: sales@autonics.com
DRW171461AB
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>