Kwikset 914ZB3 Zigbee 3.0 Polished Brass Convert Smart Lock User Guide

Kwikset 914ZB3 Zigbee 3.0 Polished Brass Convert Smart Lock

Tools needed

Parts in the box

Prepare your door

• Make sure your existing deadbolt is compatible. If you have a standard deadbolt mounted separately from the handle below it, it s compatible with Kwikset Convert.
• Make sure your door is aligned before proceeding with installation.
• Measure to confirm that your door is either 1-3/8″ or 1-3/4″ (35 mm or 44 mm) thick.
• Make sure your door is open and extend your latch bolt. Make sure your key is NOT in the deadbolt exterior.
• Secure your deadbolt exterior with masking tape.
• Remove all existing deadbolt hardware from the interior side of your door.

Determine the parts needed for your door

NOTE: You will only use one ofthe three provided kits. To determine which kit you should use, look at the hole in your door. What shape is your torque blade (the part sticking out through the latch)?

• Kwikset and Weiser deadbolts:
  Use kit “A” (5066143) for your door.

• Baldwin Estate deadbolts:
  Use kit “B” (5066145) for your door. You will need the gold adapter and the thinner gold screws.

• Schlage deadbolts:
  Use kit “C” (5066144) for your door. You will need the silver adapter.

• Schlage deadbolts:
  Use kit “C” (5066144) for your door. You will need the gold adapter.

• Baldwin Reserve and Baldwin Prestige deadbolts:
  Use kit “B” (5066145) for your door. You will need the black adapter and the thicker gold screws.

Install the mounting plate and test your latch

• Place the mounting plate on the door so that the torque blade inserts through the center hole.
• Secure the mounting plate with the mounting screws.
• Remove the masking tape from the exterior deadbolt, and insert your key and test the latch for smooth operation.
• Remove your key and make sure the bolt is fully extended.

Install the interior assembly

• Remove the interior cover and battery pack.
• Install the adapter on the interior assembly.
• Align the adapter with the torque blade and push the interior assembly onto the mounting plate.
• Secure with two (2) interior assembly screws.

Perform the door-handing process

This step will teach the lock the orientation of your door and is crucial for lock operation.

• Install 4 AA batteries in the battery pack.
• Make sure the door is open. Insert the battery pack while PRESSING AND HOLDING the Program button. Keep pressing the button for three seconds after the battery pack is installed, then release the button.
• The Status LED will flash red and green, and the lock will beep. Press and release the Program button again.
• The latch bolt will retract and extend on its own to learn the orientation of the door. Did the Status LED turn green or red?

Red Status LED
BALDWIN ESTATE DEADBOLTS:
If your latch bolt is to the RIGHT of your interior assembly, and the Status LED is solid red after door handing, press and release the Program button again. The door-handing process will restart. If you are unsure if your lock is Baldwin Estate, see step 2 on page 1

OTHER DEADBOLTS:
If the Status LED is solid red after door handing, make sure the batteries are installed correctly and the lock interior is correctly installed. Perform steps 5A-5D again. If the door handing process is still unsuccessful after a second attempt, see the Manual Door Handing section on page 4.

Confirm the lock status

• After successful handing, the Status LED blinks every six seconds to communicate whether the door is locked or unlocked.
• If the Status LED shows the opposite color to the latch bolt position, flip switch #4.

Pair the lock with your smart home system

• Initiate the pairing process through your smart home system (either through your smart home app, at your panel, or at your controller or hub). Refer to your smart home systemn instructions for more information.
• You may be prompted by your smart home system to Scan the QR code on the interior assembly. If not, proceed to step C.
• When prompted by your smart home system to initiate pairing at the lock, press button “A” on the lock interior four times.
• If the pairing process is successful, re-name the lock in your system (if applicable).
• If unsuccessful, press button “B” nine times. Perform steps 7A-7D again. If still unsuccessful, follow your smart home system’s instructions to remove (exclude/unpair) the lock from any other network. Then perform steps 7A-7D again.

Install the interior cover

Important Information about the interior cover

• The window on the interior cover is locked by default to prevent someone from tampering with your lock’s settings.
• For more convenient access to the programming buttons and the battery pack while the cover is installed, you may choose to unlock the window by removing the security screw.
• When the window is unlocked, you can slide up the window to access the battery pack and programming buttons.

Cover Installation:

• Install cover.
• Install screws.

Battery Pack Access:

If the window is locked, remove the interior cover and screws to access the battery pack and programming buttons.

If the window is unlocked, slide up the window to access the battery pack and programming buttons.

Kwikset Convert at a Glance

Status LED Notifications

Network Information

Removing the lock from the network Press button “B” on the lock interior nine times.

ZigBee System Notes

ZigBee is a “Wireless mesh network” and results may vary based on building construction and communication path, with 35+ feet being typical installed distance in a standard home environment and 250 feet+ when the lock has a clear line of sight with the smart home controller or hub. It may be necessary to install additional ZigBee devices to enhance the communication path between the lock and controller/hub for a more robust ZigBee network.

Switches
These features can be adjusted in some smart home apps. Once the associated functions are set by ZigBee, the setting of switches #1,2, and 3 no longer affect the lock operation until a factory reset is completed.

1. Status LED
   The door lock status LED blinks every 6 seconds. ON position is the factory default.

2. Auto-Locke
   Automatically re-locks door 30 seconds after unlocking. The OFF position is the factory default.

3. Audio
   A beeping sound is heard during programming and normal operation ON position is the factory default.

4. Invert A
   Only used if the Status LED is communicating the opposite door lock status.

Factory Reset
A factory reset will remove your lock from your smart home system.

1. Remove battery pack.
2. Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
3. Press the Program button once more. When the LED flashes green and you hear two beeps, the lock has been reset.
4. Perform the door-handing process again to teach the lock the orientation of the door and pair the lock to your smart home system.

Important Safeguards

1. Read al instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Always have access to your lock’s standard key.
5. If using the Auto-Lock feature, make sure to have your standard key with you to prevent locking yourself out.
6. Replace low batteries immediately.

CAUTION: Prevent unauthorized entry. Restrict access to your lock’s back panel and routinely check your settings to ensure they have not been altered without your knowledge.
WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.

©2021 Spectrum Brands, Inc. All Rights Reserved. Lake Forest, CA 92610.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>