intelbras TX 4020 Smart Universal Transmitter User Manual

intelbras TX 4020 Smart Universal Transmitter

Product Information

• Technical Specifications
  • 3 V Lithium battery, model CR2032
  • Transmission range: 100 meters without barrier
  • Frequency: 433.92 MHz
  • Modulation: Supervised (FSK) or unsupervised (OOK)
  • Data rate: 2 KBps (open source)
• Features
  • Allows wired sensors to communicate wirelessly with the alarm centre
• Digital and SMD assembly technology
  • Compatible with all Intelbras wired sensors and the majority of wired sensors available on the market
  • Works in FSK or OOK modulation
• Product Overview
  • Transmitter cover
  • Light conductor (LED)
  • Base
  • Screw hole for fixing
  • Battery contact
  • Registration button
  • Jumper (OOK/FSK)
  • Cable connector
• Sensor Opening
  • To access the TX 4020 Smartboard for registration and battery replacement, simply push the hole and remove the cover. This way the plate will be exposed and ready for handling.

Product Usage Instructions

• Registering the TX 4020 Smart transmitter
  • To register the TX 4020 Smart transmitter code in the alarm center, follow the procedure below:
  • Insert the LITHIUM 3 Vcc – CR 2032 battery, respecting polarity.
  • Refer to the alarm centre manual for the procedure to register the wireless device.
  • Press the CH1 key for approximately 2 seconds.
  • Observe whether the LED lights up after pressing the CH1 key. If it lights up, transmission has occurred. If it does not light up, check the battery and repeat the procedure.
  • Note: If the transmitter is already connected to a wired sensor, trigger the sensor and observe whether the transmitter LED lights up. If it lights up, there has been a transmission. If it does not light up, check the connection between the sensor and the transmitter or check the battery and repeat the procedure.
• TX 4020 Smart transmitter supervision adjustment
  • In FSK modulation, the transmitter transmits opening and closing signals and performs periodic supervision.
• Installation
  • The connection between TX 4020 Smart and the wired sensor
  • Follow the wiring instructions provided by Intelbras to connect the TX 4020 Smart transmitter to a wired sensor.
• Application
  • Place the TX 4020 Smart transmitter in a suitable location where it can effectively communicate with the alarm centre and wired sensor.
• Battery
  • Use a 3V Lithium battery, model CR2032, for powering the TX 4020 Smart transmitter. Replace the battery when it is depleted.
• Test
  • Perform a test after installation to ensure the proper functioning of the TX 4020 Smart transmitter and its communication with the alarm centre and wired sensor.
• Homologation
  • Ensure that the TX 4020 Smart transmitter is compliant with local regulations and requirements for homologation.
• Warranty Term
  • Refer to the warranty terms provided by Intelbras for information on warranty coverage and duration.
• FAQ
  • Q: Can I use the TX 4020 Smart transmitter with non-Intelbras wired sensors?
  • A: Yes, the TX 4020 Smart transmitter is compatible with the majority of wired sensors available on the market.
  • Q: How far is the transmission range of the TX 4020 Smart transmitter?
  • A: The transmission range of the TX 4020 Smart transmitter is 100 meters without barriers.
  • Q: What is the frequency of the TX 4020 Smart transmitter?
  • A: The TX 4020 Smart transmitter operates at a frequency of 433.92 MHz.

Care and safety

• LGPD – Data processing by Intelbras: Intelbras does not access, transfer, capture or carry out any type of processing of personal data using this product.
• This product is intended for indoor and semi-open environments.
• Avoid installing the transmitter directly under metal surfaces to avoid changes in its operating characteristics.
• Please confirm that the installation location is stable and appropriate.
• Wireless communication technology, when exposed to environments with high power radiation, may suffer interference and have its performance impaired, for example: locations close to TV towers, AM/FM radio stations, amateur radio stations, etc.
• Do not expose the TX 4020 Smart magnetic sensor directly to sunlight, rain and humidity.
• For your safety, test the product and systems at least once a week. This is necessary due to changing environmental conditions, electrical or electronic outages, and tampering. Take all necessary precautions for the safety and security of your property.

Summary

1. Technical specifications 5
2. Features 5
3. Product 6
4. Sensor opening 6
5. Registering the TX 4020 Smart transmitter 7
6. TX 4020 Smart transmitter supervision adjustment 7
7. Installation 8
8. Connection between TX 4020 Smart and wired sensor. . 9
9. Application. . 9
10. Battery 10
11. Test 10
12. Homologation 10
13. Warranty term 11

Technical specifications

Features

• Low battery indication;
• Easy installation;
• Key for registration;
• Supervised (FSK) or unsupervised (OOK);
• Long-lasting lithium battery;
• Transmission frequency 433.92 MHz.

Product

1. Transmitter cover
2. Light conductor (LED)
3. Base
4. Screw hole for fixing
5. Battery contact
6. Registration button
7. Jumper (OOK/FSK)
8. Cable connector

Sensor opening

To access the TX 4020 Smart board for registration and battery replacement, simply push the hole and remove the cover. This way the plate will be exposed and ready for handling.

Remove the board, then insert the battery (model CR2032), respecting polarity.

Registering the TX 4020 Smart transmitter

• To register the TX 4020 Smart transmitter code in the alarm center, follow the procedure below:
• Insert the LITHIUM 3 Vcc – CR 2032 battery, then enter the command to register the wireless device in the alarm center that will be used (Check the procedure in the alarm center manual).
• Then press the CH1 key for approximately 2s, observing whether the LED lights up, if the LED lights up it indicates that transmission has occurred, if it does not light up, check the battery and repeat the procedure.
  • Note: to register using the CH1 key, the transmitter must not be connected to the wired sensor.
• If the transmitter is already connected to a wired sensor, simply trigger the sensor and observe whether the transmitter LED lights up, if the LED lights up it indicates that there has been a transmission, if it does not light up, check the connection between the sensor and the transmitter or check the battery and repeat the procedure.
• Low battery sensor: the TX 4020 Smart has a battery level meter, which measures the voltage and notifies you of the best time to change it.
• If the alarm center is Intelbras, the sensor low battery warning will be indicated on the product panel. The sensor sends a low battery warning in both OOK and FSK modulations.

TX 4020 Smart transmitter supervision adjustment

• The TX 4020 Smart transmitter allows you to select between supervised (FSK) and unsupervised (OOK) modes.
• To switch between supervision modes, simply remove the battery from the transmitter, open the OOK/FSK jumper indicated on the board (and then replace the battery); once this is done, the transmitter will operate in supervised mode (FSK). Changing from supervised mode (FSK) to unsupervised mode (OOK) is also simple, just remove the battery from the transmitter, close the OOK/FSK jumper terminals again and replace the battery, once this is done the transmitter will return to operating in the unsupervised mode (OOK).
• Factory default: unattended (OOK). In FSK modulation, the transmitter transmits opening and closing and periodically performs supervision.

Installation

• The TX 4020 Smart transmitter can be fixed using double-sided tape or a screw.
• If the option with double-sided tape is chosen, clean the surface that will be in direct contact with the tape and then stick it to the base of the product.
• If you are going to use screws, simply open the transmitter and use the holes for the screw located on the base of the product, as shown in the following figure.
• To close the transmitter, position the cover on the base and press where the latches are located.

Connection between TX 4020 Smart and wired sensor

• Use an external source to power the wired sensor, then connect the alarm output cable (normally closed (NC)) of the wired sensor to the TX 4020 Smart universal transmitter terminal, as shown in the following figure:
• The maximum recommended wiring distance for installation between the TX 4020 Smart and the sensor connected to it is 1 meter.
  • Note: the ohmic resistance of the cable is very low for this distance, so you can use a cable of your choice. Once this is done, install the TX 4020 Smart transmitter in a location where it is fully protected against sunlight, rain and humidity.

Application

Battery

• Use only quality batteries, with the correct size for the device. The battery model must be CR2032, using one (1) battery per transmitter.
• This product has an internal battery. After their useful life, the batteries must be delivered to an authorized technical assistance service provided by Intelbras or directly disposed of in an environmentally appropriate manner, avoiding environmental and health impacts.
• If you prefer, the battery as well as other unused Intelbras brand electronics can be disposed of at any Green Eletron collection point (electronic waste manager to which we are associated).
• In case of doubt about the reverse logistics process, please contact us at (48) 2106-0006 or 0800 704 2767 (from Monday to Friday from 8 am to 8 pm and on Saturdays from 8 am to 6 pm) or by e-mail. -mail support@intelbras.com.br.

Test

Once installed and in operation, check whether the alarm center is receiving triggering information from the wired sensor installed on the TX 4020 Smart. If any failure occurs, it is necessary to reposition the transmitter or the alarm center. Make sure to take all precautions and follow the installation recommendations to obtain the best operating performance of the product.

Homologation

This equipment is not entitled to protection against harmful interference and may not cause interference to duly authorized systems. For more information on the approved product, visit the website: https://www.gov.br/anatel/pt-br.

Warranty term

It is established that this warranty is granted upon the following conditions:

• Client’s name:
• Client’s signature:
• Invoice number:
• Date of purchase:
• Model: Serial number:
• Retailer:

1. All the parts, pieces and components of the product are guaranteed against possible manufacturing defects, which may arise, for the term of 1 (one) year – this being 90 (ninety) days of legal guarantee and 9 (nine) months of contractual warranty –, counting from the date of purchase of the product by the Consumer, as appears in the product purchase bill of sale, which is an integral part of this Term throughout the domestic territory. This contractual warranty includes the free exchange of parts, pieces and components which have a manufacturing defect, including the expenses with labor used in this repair. If there is no manufacturing defect, but defect(s) arising from misuse, the Consumer shall bear these expenses.
2. The installation of the product shall be executed by the Product Manual and/or Installation Guide. If your product requires the installation and configuration by a qualified technician, seek a suitable specialized professional, the costs of these services not being included in the product amount.
3. Having perceived the defect, the Consumer shall immediately contact the nearest Authorized Service which appears in the report offered by the manufacturer – they are the only ones authorized to examine and remedy the defect during the warranty term foreseen herein. If this is not respected, this warranty shall lose its validity, as it shall be characterized as product infringement.
4. If the Consumer requests home service, it shall contact the nearest Authorized Service to inquire about the technical visit rate. If it is necessary to remove the product, the ensuing expenses, such as those of transportation and insurance of the taking and return of the product, shall be the Consumer’s responsibility.
5. The warranty shall lose its validity totally in the occurrence of any of the following cases: a) if the defect is not one of manufacture, but is caused by the Consumer or by third parties foreign to the manufacturer; b) if the damage to the product arises from accidents, disasters, agents of nature (lightning, floods, landslides, etc.), humidity, the voltage in the electrical network (excess voltage caused by accidents or excessive fluctuations in the network), installation/use in disagreement with the user’s manual or arising from natural wear of the parts, pieces and components; c) if the product has undergone effects of a chemical, electromagnetic, electrical or animal (insects, etc.) nature; d) if the serial number of the product has been falsified or erased; e) if the appliance has been infringed.
6. This warranty does not cover loss of data; therefore, it is advisable that if it is the case of the product, the Consumer makes a backup regularly of the data that appears in the product.
7. Intelbras is not responsible for the installation of this product, or possible attempts at fraud and/or sabotage in its products. Maintain the updates of the software and applications used up-to-date, if it is the case, as well as the network protection required for defense against hackers. The equipment is guaranteed against defects in its usual conditions of use, it is important to bear in mind that, as it is electronic equipment, it Is not free of fraud and scams which may interfere with its correct functioning.
8. After its useful life, the product must be delivered to an authorized Intelbras service centre or directly disposed of in an environmentally appropriate manner to avoid environmental and health impacts. If you prefer, the battery, as well as other unused Intelbras brand electronics, can be disposed of at any Green Eletron collection point (waste management facility to which we are associated). If you have any questions about the reverse logistics process, please contact us at (48) 2106-0006 or 0800 704 2767 (Monday to Friday 8am to 8pm and Saturdays 8am to 6pm) or via -mail support@intelbras.com.br.
9. These being the conditions of this complementary Warranty Term, Intelbras S/A reserves the right to alter the general, technical and esthetic features of its products without prior notice. All the images of this manual are illustrative.

CONTACT

• Customer Support: (48) 2106 0006
• Forum: forum.intelbras.com.br.
• Support via chat: chat.intelbras.com.br.
• Support via e-mail: suporte@intelbras.com.br.
• Customer Service: 0800 7042767
• Where to buy? Who installs it? 0800 7245115
• Produced by: Intelbras S/A – Indústria de Telecomunicação Eletrônica Brasileira
• Rodovia BR 459, km 124, 1325 – Distrito Industrial – Santa Rita do Sapucaí/MG – 37540-000
• CNPJ 82.901.000/0016-03 – www.intelbras.com.br.
• www.intelbras.com.
• 01.23 Made in Brazil
• TX 4020 Smart

TX 4020 Smart Universal transmitter

• Congratulations, you have just purchased a product with Intelbras quality and safety.
• The TX 4020 Smart universal transmitter was developed to facilitate the installation of wired sensors in your daily life, as it allows a wired sensor to communicate wirelessly with the alarm center.
• With digital and SMD assembly technology, it is compatible with all Intelbras wired sensors and the majority of wired sensors available on the market.
• Works in FSK or OOK modulation. Carefully read the information in this manual for the correct use of the transmitter.

References

• Fórum Intelbras - Índice
• intelbras.com.br/suporte-tecnico
• intelbras.com
• Manual-Hub.com – Free PDF manuals!
• Anatel — Agência Nacional de Telecomunicações

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>